lkml.org 
[lkml]   [2022]   [Apr]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH V2 06/15] cpufreq: mediatek: Record previous target vproc value
From
Date
On Mon, 2022-04-11 at 08:56 +0530, Viresh Kumar wrote:
> On 08-04-22, 12:58, Rex-BC Chen wrote:
> > From: Jia-Wei Chang <jia-wei.chang@mediatek.com>
> >
> > We found the buck voltage may not be exactly the same with what we
> > set
> > because CPU may share the same buck with other module.
> > Therefore, we need to record the previous desired value instead of
> > reading
> > it from regulators.
> >
> > Signed-off-by: Andrew-sh.Cheng <andrew-sh.cheng@mediatek.com>
> > Signed-off-by: Jia-Wei Chang <jia-wei.chang@mediatek.com>
> > ---
> > drivers/cpufreq/mediatek-cpufreq.c | 31 +++++++++++++++++++-------
> > ----
> > 1 file changed, 20 insertions(+), 11 deletions(-)
> >
> > diff --git a/drivers/cpufreq/mediatek-cpufreq.c
> > b/drivers/cpufreq/mediatek-cpufreq.c
> > index dc4a87e68940..472f4de29e5f 100644
> > --- a/drivers/cpufreq/mediatek-cpufreq.c
> > +++ b/drivers/cpufreq/mediatek-cpufreq.c
> > @@ -40,6 +40,7 @@ struct mtk_cpu_dvfs_info {
> > struct list_head list_head;
> > int intermediate_voltage;
> > bool need_voltage_tracking;
> > + int old_vproc;
>
> I like prev_vproc better somehow, but it is up to you to name it :)

Hello Viresh,

Thanks for your review.
I will modify this as prev_vproc in next version.

>
> > };
> >
> > static LIST_HEAD(dvfs_info_list);
> > @@ -190,11 +191,17 @@ static int
> > mtk_cpufreq_voltage_tracking(struct mtk_cpu_dvfs_info *info,
> >
> > static int mtk_cpufreq_set_voltage(struct mtk_cpu_dvfs_info *info,
> > int vproc)
> > {
> > + int ret;
> > +
> > if (info->need_voltage_tracking)
> > - return mtk_cpufreq_voltage_tracking(info, vproc);
> > + ret = mtk_cpufreq_voltage_tracking(info, vproc);
> > else
> > - return regulator_set_voltage(info->proc_reg, vproc,
> > - vproc + VOLT_TOL);
> > + ret = regulator_set_voltage(info->proc_reg, vproc,
> > + MAX_VOLT_LIMIT);
> > + if (!ret)
> > + info->old_vproc = vproc;
> > +
> > + return ret;
> > }
> >
> > static int mtk_cpufreq_set_target(struct cpufreq_policy *policy,
> > @@ -211,15 +218,7 @@ static int mtk_cpufreq_set_target(struct
> > cpufreq_policy *policy,
> >
> > inter_vproc = info->intermediate_voltage;
> >
> > - old_freq_hz = clk_get_rate(cpu_clk);
> > - old_vproc = regulator_get_voltage(info->proc_reg);
> > - if (old_vproc < 0) {
> > - pr_err("%s: invalid Vproc value: %d\n", __func__,
> > old_vproc);
> > - return old_vproc;
> > - }
> > -
>
> Why did you move it down from here? I think it was fine to error out
> early if voltage isn't available.

I will move them to original position in next version.

Thanks!

BRs,
Rex

>
> > freq_hz = freq_table[index].frequency * 1000;
> > -
> > opp = dev_pm_opp_find_freq_ceil(cpu_dev, &freq_hz);
> > if (IS_ERR(opp)) {
> > pr_err("cpu%d: failed to find OPP for %ld\n",
> > @@ -229,6 +228,16 @@ static int mtk_cpufreq_set_target(struct
> > cpufreq_policy *policy,
> > vproc = dev_pm_opp_get_voltage(opp);
> > dev_pm_opp_put(opp);
> >
> > + old_freq_hz = clk_get_rate(cpu_clk);
> > + old_vproc = info->old_vproc;
> > + if (old_vproc == 0)
> > + old_vproc = regulator_get_voltage(info->proc_reg);
> > + if (old_vproc < 0) {
> > + dev_err(cpu_dev, "%s: invalid Vproc value: %d\n",
> > + __func__, old_vproc);
> > + return old_vproc;
> > + }
> > +
> > /*
> > * If the new voltage or the intermediate voltage is higher
> > than the
> > * current voltage, scale up voltage first.
> > --
> > 2.18.0
>
>

\
 
 \ /
  Last update: 2022-04-11 13:34    [W:0.075 / U:1.276 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site