lkml.org 
[lkml]   [2022]   [Apr]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 06/10] ARM: dts: qcom: msm8974: override nodes by label
Date
Using node paths to extend or override a device tree node is error
prone. If there was a typo error, a new node will be created instead of
extending the existing node. This will lead to run-time errors that
could be hard to detect.

A mistyped label on the other hand, will cause a dtc compile error
(during build time). This also reduces the indentation making the code
easier to read.

Re-order the overrides by label name. The pre/post DTBS are the same.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
.../arm/boot/dts/qcom-apq8074-dragonboard.dts | 614 +++++-----
.../boot/dts/qcom-msm8974-fairphone-fp2.dts | 581 +++++----
.../qcom-msm8974-lge-nexus5-hammerhead.dts | 1075 ++++++++--------
.../boot/dts/qcom-msm8974-samsung-klte.dts | 1083 ++++++++---------
.../dts/qcom-msm8974-sony-xperia-amami.dts | 569 +++++----
.../dts/qcom-msm8974-sony-xperia-castor.dts | 908 +++++++-------
.../dts/qcom-msm8974-sony-xperia-honami.dts | 636 +++++-----
arch/arm/boot/dts/qcom-msm8974.dtsi | 16 +-
8 files changed, 2730 insertions(+), 2752 deletions(-)

diff --git a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
index 83793b835d40..4c510701ff83 100644
--- a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
+++ b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
@@ -17,330 +17,324 @@ chosen {
stdout-path = "serial0:115200n8";
};

- soc {
- serial@f991e000 {
- status = "okay";
+};
+
+&blsp_i2c11 {
+ status = "okay";
+ clock-frequency = <200000>;
+ pinctrl-0 = <&i2c11_pins>;
+ pinctrl-names = "default";
+
+ eeprom: eeprom@52 {
+ compatible = "atmel,24c128";
+ reg = <0x52>;
+ pagesize = <32>;
+ read-only;
+ };
+};
+
+&blsp1_uart2 {
+ status = "okay";
+};
+
+&msmgpio {
+ i2c11_pins: i2c11 {
+ mux {
+ pins = "gpio83", "gpio84";
+ function = "blsp_i2c11";
};
+ };

- sdhci@f9824900 {
- bus-width = <8>;
- non-removable;
- status = "okay";
+ spi8_default: spi8_default {
+ mosi {
+ pins = "gpio45";
+ function = "blsp_spi8";
+ };
+ miso {
+ pins = "gpio46";
+ function = "blsp_spi8";
+ };
+ cs {
+ pins = "gpio47";
+ function = "blsp_spi8";
+ };
+ clk {
+ pins = "gpio48";
+ function = "blsp_spi8";
+ };
+ };

- vmmc-supply = <&pm8941_l20>;
- vqmmc-supply = <&pm8941_s3>;
+ sdhc1_pin_a: sdhc1-pin-active {
+ clk {
+ pins = "sdc1_clk";
+ drive-strength = <16>;
+ bias-disable;
+ };

- pinctrl-names = "default";
- pinctrl-0 = <&sdhc1_pin_a>;
+ cmd-data {
+ pins = "sdc1_cmd", "sdc1_data";
+ drive-strength = <10>;
+ bias-pull-up;
};
+ };

- sdhci@f98a4900 {
- cd-gpios = <&msmgpio 62 0x1>;
- pinctrl-names = "default";
- pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
- bus-width = <4>;
- status = "okay";
+ sdhc2_cd_pin_a: sdhc2-cd-pin-active {
+ pins = "gpio62";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-disable;
+ };

- vmmc-supply = <&pm8941_l21>;
- vqmmc-supply = <&pm8941_l13>;
+ sdhc2_pin_a: sdhc2-pin-active {
+ clk {
+ pins = "sdc2_clk";
+ drive-strength = <10>;
+ bias-disable;
};

- usb@f9a55000 {
- status = "okay";
- phys = <&usb_hs2_phy>;
- phy-select = <&tcsr 0xb000 1>;
- extcon = <&smbb>, <&usb_id>;
- vbus-supply = <&chg_otg>;
- hnp-disable;
- srp-disable;
- adp-disable;
- ulpi {
- phy@b {
- status = "okay";
- v3p3-supply = <&pm8941_l24>;
- v1p8-supply = <&pm8941_l6>;
- extcon = <&smbb>;
- qcom,init-seq = /bits/ 8 <0x1 0x63>;
- };
- };
- };
-
-
- pinctrl@fd510000 {
- i2c11_pins: i2c11 {
- mux {
- pins = "gpio83", "gpio84";
- function = "blsp_i2c11";
- };
- };
-
- spi8_default: spi8_default {
- mosi {
- pins = "gpio45";
- function = "blsp_spi8";
- };
- miso {
- pins = "gpio46";
- function = "blsp_spi8";
- };
- cs {
- pins = "gpio47";
- function = "blsp_spi8";
- };
- clk {
- pins = "gpio48";
- function = "blsp_spi8";
- };
- };
-
- sdhc1_pin_a: sdhc1-pin-active {
- clk {
- pins = "sdc1_clk";
- drive-strength = <16>;
- bias-disable;
- };
-
- cmd-data {
- pins = "sdc1_cmd", "sdc1_data";
- drive-strength = <10>;
- bias-pull-up;
- };
- };
-
- sdhc2_cd_pin_a: sdhc2-cd-pin-active {
- pins = "gpio62";
- function = "gpio";
-
- drive-strength = <2>;
- bias-disable;
- };
-
- sdhc2_pin_a: sdhc2-pin-active {
- clk {
- pins = "sdc2_clk";
- drive-strength = <10>;
- bias-disable;
- };
-
- cmd-data {
- pins = "sdc2_cmd", "sdc2_data";
- drive-strength = <6>;
- bias-pull-up;
- };
- };
- };
-
- i2c@f9967000 {
+ cmd-data {
+ pins = "sdc2_cmd", "sdc2_data";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+ };
+};
+
+&otg {
+ status = "okay";
+ phys = <&usb_hs2_phy>;
+ phy-select = <&tcsr 0xb000 1>;
+ extcon = <&smbb>, <&usb_id>;
+ vbus-supply = <&chg_otg>;
+ hnp-disable;
+ srp-disable;
+ adp-disable;
+ ulpi {
+ phy@b {
status = "okay";
- clock-frequency = <200000>;
- pinctrl-0 = <&i2c11_pins>;
- pinctrl-names = "default";
+ v3p3-supply = <&pm8941_l24>;
+ v1p8-supply = <&pm8941_l6>;
+ extcon = <&smbb>;
+ qcom,init-seq = /bits/ 8 <0x1 0x63>;
+ };
+ };
+};
+
+&rpm_requests {
+ pm8841-regulators {
+ s1 {
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <1050000>;
+ };

- eeprom: eeprom@52 {
- compatible = "atmel,24c128";
- reg = <0x52>;
- pagesize = <32>;
- read-only;
- };
+ s2 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
+ };
+
+ s3 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
+ };
+
+ s4 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
};
};

- smd {
- rpm {
- rpm_requests {
- pm8841-regulators {
- s1 {
- regulator-min-microvolt = <675000>;
- regulator-max-microvolt = <1050000>;
- };
-
- s2 {
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <1050000>;
- };
-
- s3 {
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <1050000>;
- };
-
- s4 {
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <1050000>;
- };
- };
-
- pm8941-regulators {
- vdd_l1_l3-supply = <&pm8941_s1>;
- vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
- vdd_l4_l11-supply = <&pm8941_s1>;
- vdd_l5_l7-supply = <&pm8941_s2>;
- vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
- vin_5vs-supply = <&pm8941_5v>;
-
- s1 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- s2 {
- regulator-min-microvolt = <2150000>;
- regulator-max-microvolt = <2150000>;
- regulator-boot-on;
- };
-
- s3 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- l1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- l2 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l3 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l4 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-boot-on;
- };
-
- l7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-boot-on;
- };
-
- l8 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l9 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l10 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- l11 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- };
-
- l12 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- l13 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-boot-on;
- };
-
- l14 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l15 {
- regulator-min-microvolt = <2050000>;
- regulator-max-microvolt = <2050000>;
- };
-
- l16 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-
- l17 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-
- l18 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- l19 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- l20 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-allow-set-load;
- regulator-boot-on;
- regulator-system-load = <200000>;
- };
-
- l21 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-boot-on;
- };
-
- l22 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- l23 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- l24 {
- regulator-min-microvolt = <3075000>;
- regulator-max-microvolt = <3075000>;
-
- regulator-boot-on;
- };
- };
- };
+ pm8941-regulators {
+ vdd_l1_l3-supply = <&pm8941_s1>;
+ vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+ vdd_l4_l11-supply = <&pm8941_s1>;
+ vdd_l5_l7-supply = <&pm8941_s2>;
+ vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+ vin_5vs-supply = <&pm8941_5v>;
+
+ s1 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ s2 {
+ regulator-min-microvolt = <2150000>;
+ regulator-max-microvolt = <2150000>;
+ regulator-boot-on;
+ };
+
+ s3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ l1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ l3 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
+
+ l4 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
+
+ l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-boot-on;
+ };
+
+ l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-boot-on;
+ };
+
+ l8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ l10 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ l11 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ };
+
+ l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ l13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-boot-on;
+ };
+
+ l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l15 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };
+
+ l16 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ l17 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ l18 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ l19 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ l20 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-allow-set-load;
+ regulator-boot-on;
+ regulator-system-load = <200000>;
+ };
+
+ l21 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-boot-on;
+ };
+
+ l22 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ l23 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ l24 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+
+ regulator-boot-on;
};
};
};
+
+&sdhci1 {
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+
+ vmmc-supply = <&pm8941_l20>;
+ vqmmc-supply = <&pm8941_s3>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc1_pin_a>;
+};
+
+&sdhci3 {
+ cd-gpios = <&msmgpio 62 0x1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
+ bus-width = <4>;
+ status = "okay";
+
+ vmmc-supply = <&pm8941_l21>;
+ vqmmc-supply = <&pm8941_l13>;
+};
diff --git a/arch/arm/boot/dts/qcom-msm8974-fairphone-fp2.dts b/arch/arm/boot/dts/qcom-msm8974-fairphone-fp2.dts
index 6d77e0f8ca4d..f72a53a0e962 100644
--- a/arch/arm/boot/dts/qcom-msm8974-fairphone-fp2.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-fairphone-fp2.dts
@@ -55,345 +55,340 @@ vibrator {
vcc-supply = <&pm8941_l18>;
};

- smd {
- rpm {
- rpm_requests {
- pm8841-regulators {
- s1 {
- regulator-min-microvolt = <675000>;
- regulator-max-microvolt = <1050000>;
- };
-
- s2 {
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <1050000>;
- };
-
- s3 {
- regulator-min-microvolt = <1050000>;
- regulator-max-microvolt = <1050000>;
- };
- };
-
- pm8941-regulators {
- vdd_l1_l3-supply = <&pm8941_s1>;
- vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
- vdd_l4_l11-supply = <&pm8941_s1>;
- vdd_l5_l7-supply = <&pm8941_s2>;
- vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
- vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
- vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
- vdd_l21-supply = <&vreg_boost>;
-
- s1 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- s2 {
- regulator-min-microvolt = <2150000>;
- regulator-max-microvolt = <2150000>;
-
- regulator-boot-on;
- };
-
- s3 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- l1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- l2 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l3 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l4 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-boot-on;
- };
-
- l7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-boot-on;
- };
-
- l8 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l9 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l10 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l11 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1350000>;
- };
-
- l12 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- l13 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-boot-on;
- };
-
- l14 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l15 {
- regulator-min-microvolt = <2050000>;
- regulator-max-microvolt = <2050000>;
- };
-
- l16 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-
- l17 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- l18 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- l19 {
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <3350000>;
- };
-
- l20 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-boot-on;
- regulator-system-load = <200000>;
- regulator-allow-set-load;
- };
-
- l21 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-boot-on;
- };
-
- l22 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l23 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- l24 {
- regulator-min-microvolt = <3075000>;
- regulator-max-microvolt = <3075000>;
-
- regulator-boot-on;
- };
- };
- };
+};
+
+&blsp1_uart2 {
+ status = "okay";
+};
+
+&imem {
+ status = "okay";
+
+ reboot-mode {
+ mode-normal = <0x77665501>;
+ mode-bootloader = <0x77665500>;
+ mode-recovery = <0x77665502>;
+ };
+};
+
+&msmgpio {
+ sdhc1_pin_a: sdhc1-pin-active {
+ clk {
+ pins = "sdc1_clk";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ cmd-data {
+ pins = "sdc1_cmd", "sdc1_data";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+ };
+
+ sdhc2_pin_a: sdhc2-pin-active {
+ clk {
+ pins = "sdc2_clk";
+ drive-strength = <10>;
+ bias-disable;
+ };
+
+ cmd-data {
+ pins = "sdc2_cmd", "sdc2_data";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+ };
+
+ wcnss_pin_a: wcnss-pin-active {
+ wlan {
+ pins = "gpio36", "gpio37", "gpio38", "gpio39", "gpio40";
+ function = "wlan";
+
+ drive-strength = <6>;
+ bias-pull-down;
+ };
+
+ bt {
+ pins = "gpio35", "gpio43", "gpio44";
+ function = "bt";
+
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ fm {
+ pins = "gpio41", "gpio42";
+ function = "fm";
+
+ drive-strength = <2>;
+ bias-pull-down;
};
};
};

-&soc {
- serial@f991e000 {
- status = "okay";
+&otg {
+ status = "okay";
+
+ phys = <&usb_hs1_phy>;
+ phy-select = <&tcsr 0xb000 0>;
+ extcon = <&smbb>, <&usb_id>;
+ vbus-supply = <&chg_otg>;
+
+ hnp-disable;
+ srp-disable;
+ adp-disable;
+
+ ulpi {
+ phy@a {
+ status = "okay";
+
+ v1p8-supply = <&pm8941_l6>;
+ v3p3-supply = <&pm8941_l24>;
+
+ extcon = <&smbb>;
+ qcom,init-seq = /bits/ 8 <0x1 0x64>;
+ };
};
+};

- remoteproc@fb21b000 {
- status = "okay";
+&pronto {
+ status = "okay";

- vddmx-supply = <&pm8841_s1>;
- vddcx-supply = <&pm8841_s2>;
+ vddmx-supply = <&pm8841_s1>;
+ vddcx-supply = <&pm8841_s2>;

- pinctrl-names = "default";
- pinctrl-0 = <&wcnss_pin_a>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&wcnss_pin_a>;

- smd-edge {
- qcom,remote-pid = <4>;
- label = "pronto";
+ smd-edge {
+ qcom,remote-pid = <4>;
+ label = "pronto";

- wcnss {
- status = "okay";
- };
+ wcnss {
+ status = "okay";
};
};
+};

- pinctrl@fd510000 {
- sdhc1_pin_a: sdhc1-pin-active {
- clk {
- pins = "sdc1_clk";
- drive-strength = <16>;
- bias-disable;
- };
+&rpm_requests {
+ pm8841-regulators {
+ s1 {
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <1050000>;
+ };

- cmd-data {
- pins = "sdc1_cmd", "sdc1_data";
- drive-strength = <10>;
- bias-pull-up;
- };
+ s2 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
};

- sdhc2_pin_a: sdhc2-pin-active {
- clk {
- pins = "sdc2_clk";
- drive-strength = <10>;
- bias-disable;
- };
+ s3 {
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ };
+ };

- cmd-data {
- pins = "sdc2_cmd", "sdc2_data";
- drive-strength = <6>;
- bias-pull-up;
- };
+ pm8941-regulators {
+ vdd_l1_l3-supply = <&pm8941_s1>;
+ vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+ vdd_l4_l11-supply = <&pm8941_s1>;
+ vdd_l5_l7-supply = <&pm8941_s2>;
+ vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+ vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
+ vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
+ vdd_l21-supply = <&vreg_boost>;
+
+ s1 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+
+ regulator-always-on;
+ regulator-boot-on;
};

- wcnss_pin_a: wcnss-pin-active {
- wlan {
- pins = "gpio36", "gpio37", "gpio38", "gpio39", "gpio40";
- function = "wlan";
+ s2 {
+ regulator-min-microvolt = <2150000>;
+ regulator-max-microvolt = <2150000>;

- drive-strength = <6>;
- bias-pull-down;
- };
+ regulator-boot-on;
+ };

- bt {
- pins = "gpio35", "gpio43", "gpio44";
- function = "bt";
+ s3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;

- drive-strength = <2>;
- bias-pull-down;
- };
+ regulator-always-on;
+ regulator-boot-on;
+ };

- fm {
- pins = "gpio41", "gpio42";
- function = "fm";
+ l1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;

- drive-strength = <2>;
- bias-pull-down;
- };
+ regulator-always-on;
+ regulator-boot-on;
};
- };

- sdhci@f9824900 {
- status = "okay";
+ l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };

- vmmc-supply = <&pm8941_l20>;
- vqmmc-supply = <&pm8941_s3>;
+ l3 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };

- bus-width = <8>;
- non-removable;
+ l4 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };

- pinctrl-names = "default";
- pinctrl-0 = <&sdhc1_pin_a>;
- };
+ l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };

- sdhci@f98a4900 {
- status = "okay";
+ l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;

- vmmc-supply = <&pm8941_l21>;
- vqmmc-supply = <&pm8941_l13>;
+ regulator-boot-on;
+ };

- bus-width = <4>;
+ l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;

- pinctrl-names = "default";
- pinctrl-0 = <&sdhc2_pin_a>;
- };
+ regulator-boot-on;
+ };
+
+ l8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };

- usb@f9a55000 {
- status = "okay";
+ l10 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };

- phys = <&usb_hs1_phy>;
- phy-select = <&tcsr 0xb000 0>;
- extcon = <&smbb>, <&usb_id>;
- vbus-supply = <&chg_otg>;
+ l11 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1350000>;
+ };

- hnp-disable;
- srp-disable;
- adp-disable;
+ l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;

- ulpi {
- phy@a {
- status = "okay";
+ regulator-always-on;
+ regulator-boot-on;
+ };

- v1p8-supply = <&pm8941_l6>;
- v3p3-supply = <&pm8941_l24>;
+ l13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;

- extcon = <&smbb>;
- qcom,init-seq = /bits/ 8 <0x1 0x64>;
- };
+ regulator-boot-on;
};
- };

- imem@fe805000 {
- status = "okay";
+ l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l15 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };
+
+ l16 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ l17 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };

- reboot-mode {
- mode-normal = <0x77665501>;
- mode-bootloader = <0x77665500>;
- mode-recovery = <0x77665502>;
+ l18 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ l19 {
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <3350000>;
+ };
+
+ l20 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-boot-on;
+ regulator-system-load = <200000>;
+ regulator-allow-set-load;
+ };
+
+ l21 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-boot-on;
+ };
+
+ l22 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ l23 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ l24 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+
+ regulator-boot-on;
};
};
};

+&sdhci1 {
+ status = "okay";
+
+ vmmc-supply = <&pm8941_l20>;
+ vqmmc-supply = <&pm8941_s3>;
+
+ bus-width = <8>;
+ non-removable;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc1_pin_a>;
+};
+
+&sdhci3 {
+ status = "okay";
+
+ vmmc-supply = <&pm8941_l21>;
+ vqmmc-supply = <&pm8941_l13>;
+
+ bus-width = <4>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc2_pin_a>;
+};
+
&spmi_bus {
pm8941@0 {
gpios@c000 {
diff --git a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
index 6d5fb60e798f..a72ef21b2fc7 100644
--- a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
@@ -40,209 +40,6 @@ volume-down {
};
};

- smd {
- rpm {
- rpm_requests {
- pm8841-regulators {
- s1 {
- regulator-min-microvolt = <675000>;
- regulator-max-microvolt = <1050000>;
- };
-
- s2 {
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <1050000>;
- };
-
- s3 {
- regulator-min-microvolt = <1050000>;
- regulator-max-microvolt = <1050000>;
- };
-
- s4 {
- regulator-min-microvolt = <815000>;
- regulator-max-microvolt = <900000>;
- };
- };
-
- pm8941-regulators {
- vdd_l1_l3-supply = <&pm8941_s1>;
- vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
- vdd_l4_l11-supply = <&pm8941_s1>;
- vdd_l5_l7-supply = <&pm8941_s2>;
- vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
- vdd_l8_l16_l18_l19-supply = <&vreg_vph_pwr>;
- vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
- vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
- vdd_l21-supply = <&vreg_boost>;
-
- s1 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- s2 {
- regulator-min-microvolt = <2150000>;
- regulator-max-microvolt = <2150000>;
-
- regulator-boot-on;
- };
-
- s3 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- l1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- l2 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l3 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l4 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-boot-on;
- };
-
- l7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-boot-on;
- };
-
- l8 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l9 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l10 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l11 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- };
-
- l12 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- l13 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-boot-on;
- };
-
- l14 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l15 {
- regulator-min-microvolt = <2050000>;
- regulator-max-microvolt = <2050000>;
- };
-
- l16 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-
- l17 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- l18 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- l19 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l20 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-boot-on;
- regulator-system-load = <200000>;
- regulator-allow-set-load;
- };
-
- l21 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-boot-on;
- };
-
- l22 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l23 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- l24 {
- regulator-min-microvolt = <3075000>;
- regulator-max-microvolt = <3075000>;
-
- regulator-boot-on;
- };
- };
- };
- };
- };
-
vreg_wlan: wlan-regulator {
compatible = "regulator-fixed";

@@ -256,464 +53,682 @@ vreg_wlan: wlan-regulator {
pinctrl-names = "default";
pinctrl-0 = <&wlan_regulator_pin>;
};
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_keys_pin_a>;
+
+ volume-up {
+ label = "volume_up";
+ gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
+ linux,input-type = <1>;
+ linux,code = <KEY_VOLUMEUP>;
+ };
+
+ volume-down {
+ label = "volume_down";
+ gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
+ linux,input-type = <1>;
+ linux,code = <KEY_VOLUMEDOWN>;
+ };
+ };
};

-&soc {
- serial@f991d000 {
- status = "okay";
+&blsp1_uart1 {
+ status = "okay";
+};
+
+&blsp2_uart10 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp2_uart10_pin_a>;
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ max-speed = <3000000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_pin>;
+
+ host-wakeup-gpios = <&msmgpio 42 GPIO_ACTIVE_HIGH>;
+ device-wakeup-gpios = <&msmgpio 62 GPIO_ACTIVE_HIGH>;
+ shutdown-gpios = <&msmgpio 41 GPIO_ACTIVE_HIGH>;
};
+};

- pinctrl@fd510000 {
- sdhc1_pin_a: sdhc1-pin-active {
- clk {
- pins = "sdc1_clk";
- drive-strength = <16>;
- bias-disable;
- };
+&blsp_i2c1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+ clock-frequency = <100000>;
+ qcom,src-freq = <50000000>;

- cmd-data {
- pins = "sdc1_cmd", "sdc1_data";
- drive-strength = <10>;
- bias-pull-up;
- };
+ charger: bq24192@6b {
+ compatible = "ti,bq24192";
+ reg = <0x6b>;
+ interrupts-extended = <&spmi_bus 0 0xd5 0 IRQ_TYPE_EDGE_FALLING>;
+
+ omit-battery-class;
+
+ usb_otg_vbus: usb-otg-vbus { };
+ };
+
+ fuelgauge: max17048@36 {
+ compatible = "maxim,max17048";
+ reg = <0x36>;
+
+ maxim,double-soc;
+ maxim,rcomp = /bits/ 8 <0x4d>;
+
+ interrupt-parent = <&msmgpio>;
+ interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&fuelgauge_pin>;
+
+ maxim,alert-low-soc-level = <2>;
+ };
+};
+
+&blsp_i2c2 {
+ status = "okay";
+
+ clock-frequency = <355000>;
+ qcom,src-freq = <50000000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
+
+ synaptics@70 {
+ compatible = "syna,rmi4-i2c";
+ reg = <0x70>;
+
+ interrupts-extended = <&msmgpio 5 IRQ_TYPE_EDGE_FALLING>;
+ vdd-supply = <&pm8941_l22>;
+ vio-supply = <&pm8941_lvs3>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&touch_pin>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rmi4-f01@1 {
+ reg = <0x1>;
+ syna,nosleep-mode = <1>;
};

- sdhc2_pin_a: sdhc2-pin-active {
- clk {
- pins = "sdc2_clk";
- drive-strength = <6>;
- bias-disable;
+ rmi4-f12@12 {
+ reg = <0x12>;
+ syna,sensor-type = <1>;
+ };
+ };
+};
+
+&blsp_i2c3 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_pins>;
+ clock-frequency = <100000>;
+ qcom,src-freq = <50000000>;
+
+ avago_apds993@39 {
+ compatible = "avago,apds9930";
+ reg = <0x39>;
+ interrupts-extended = <&msmgpio 61 IRQ_TYPE_EDGE_FALLING>;
+ vdd-supply = <&pm8941_l17>;
+ vddio-supply = <&pm8941_lvs1>;
+ led-max-microamp = <100000>;
+ amstaos,proximity-diodes = <0>;
+ };
+};
+
+&blsp_i2c11 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c11_pins>;
+ clock-frequency = <355000>;
+ qcom,src-freq = <50000000>;
+
+ led-controller@38 {
+ compatible = "ti,lm3630a";
+ status = "okay";
+ reg = <0x38>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ led-sources = <0 1>;
+ label = "lcd-backlight";
+ default-brightness = <200>;
+ };
+ };
+};
+
+&blsp_i2c12 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c12_pins>;
+ clock-frequency = <100000>;
+ qcom,src-freq = <50000000>;
+
+ mpu6515@68 {
+ compatible = "invensense,mpu6515";
+ reg = <0x68>;
+ interrupts-extended = <&msmgpio 73 IRQ_TYPE_EDGE_FALLING>;
+ vddio-supply = <&pm8941_lvs1>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&mpu6515_pin>;
+
+ mount-matrix = "0", "-1", "0",
+ "-1", "0", "0",
+ "0", "0", "1";
+
+ i2c-gate {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ak8963@f {
+ compatible = "asahi-kasei,ak8963";
+ reg = <0x0f>;
+ gpios = <&msmgpio 67 0>;
+ vid-supply = <&pm8941_lvs1>;
+ vdd-supply = <&pm8941_l17>;
};

- cmd-data {
- pins = "sdc2_cmd", "sdc2_data";
- drive-strength = <6>;
- bias-pull-up;
+ bmp280@76 {
+ compatible = "bosch,bmp280";
+ reg = <0x76>;
+ vdda-supply = <&pm8941_lvs1>;
+ vddd-supply = <&pm8941_l17>;
};
};
+ };
+};

- i2c1_pins: i2c1 {
- mux {
- pins = "gpio2", "gpio3";
- function = "blsp_i2c1";
+&msmgpio {
+ sdhc1_pin_a: sdhc1-pin-active {
+ clk {
+ pins = "sdc1_clk";
+ drive-strength = <16>;
+ bias-disable;
+ };

- drive-strength = <2>;
- bias-disable;
- };
+ cmd-data {
+ pins = "sdc1_cmd", "sdc1_data";
+ drive-strength = <10>;
+ bias-pull-up;
};
+ };

- i2c2_pins: i2c2 {
- mux {
- pins = "gpio6", "gpio7";
- function = "blsp_i2c2";
+ sdhc2_pin_a: sdhc2-pin-active {
+ clk {
+ pins = "sdc2_clk";
+ drive-strength = <6>;
+ bias-disable;
+ };

- drive-strength = <2>;
- bias-disable;
- };
+ cmd-data {
+ pins = "sdc2_cmd", "sdc2_data";
+ drive-strength = <6>;
+ bias-pull-up;
};
+ };

- i2c3_pins: i2c3 {
- mux {
- pins = "gpio10", "gpio11";
- function = "blsp_i2c3";
- drive-strength = <2>;
- bias-disable;
- };
+ i2c1_pins: i2c1 {
+ mux {
+ pins = "gpio2", "gpio3";
+ function = "blsp_i2c1";
+
+ drive-strength = <2>;
+ bias-disable;
};
+ };

- i2c11_pins: i2c11 {
- mux {
- pins = "gpio83", "gpio84";
- function = "blsp_i2c11";
+ i2c2_pins: i2c2 {
+ mux {
+ pins = "gpio6", "gpio7";
+ function = "blsp_i2c2";

- drive-strength = <2>;
- bias-disable;
- };
+ drive-strength = <2>;
+ bias-disable;
};
+ };

- i2c12_pins: i2c12 {
- mux {
- pins = "gpio87", "gpio88";
- function = "blsp_i2c12";
- drive-strength = <2>;
- bias-disable;
- };
+ i2c3_pins: i2c3 {
+ mux {
+ pins = "gpio10", "gpio11";
+ function = "blsp_i2c3";
+ drive-strength = <2>;
+ bias-disable;
};
+ };

- mpu6515_pin: mpu6515 {
- irq {
- pins = "gpio73";
- function = "gpio";
- bias-disable;
- input-enable;
- };
+ i2c11_pins: i2c11 {
+ mux {
+ pins = "gpio83", "gpio84";
+ function = "blsp_i2c11";
+
+ drive-strength = <2>;
+ bias-disable;
};
+ };

- touch_pin: touch {
- int {
- pins = "gpio5";
- function = "gpio";
+ i2c12_pins: i2c12 {
+ mux {
+ pins = "gpio87", "gpio88";
+ function = "blsp_i2c12";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };

- drive-strength = <2>;
- bias-disable;
- input-enable;
- };
+ mpu6515_pin: mpu6515 {
+ irq {
+ pins = "gpio73";
+ function = "gpio";
+ bias-disable;
+ input-enable;
+ };
+ };

- reset {
- pins = "gpio8";
- function = "gpio";
+ touch_pin: touch {
+ int {
+ pins = "gpio5";
+ function = "gpio";

- drive-strength = <2>;
- bias-pull-up;
- };
+ drive-strength = <2>;
+ bias-disable;
+ input-enable;
};

- panel_pin: panel {
- te {
- pins = "gpio12";
- function = "mdp_vsync";
+ reset {
+ pins = "gpio8";
+ function = "gpio";

- drive-strength = <2>;
- bias-disable;
- };
+ drive-strength = <2>;
+ bias-pull-up;
};
+ };

- bt_pin: bt {
- hostwake {
- pins = "gpio42";
- function = "gpio";
- };
+ panel_pin: panel {
+ te {
+ pins = "gpio12";
+ function = "mdp_vsync";

- devwake {
- pins = "gpio62";
- function = "gpio";
- };
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };

- shutdown {
- pins = "gpio41";
- function = "gpio";
- };
+ bt_pin: bt {
+ hostwake {
+ pins = "gpio42";
+ function = "gpio";
};

- blsp2_uart10_pin_a: blsp2-uart10-pin-active {
- tx {
- pins = "gpio53";
- function = "blsp_uart10";
+ devwake {
+ pins = "gpio62";
+ function = "gpio";
+ };

- drive-strength = <2>;
- bias-disable;
- };
+ shutdown {
+ pins = "gpio41";
+ function = "gpio";
+ };
+ };

- rx {
- pins = "gpio54";
- function = "blsp_uart10";
+ blsp2_uart10_pin_a: blsp2-uart10-pin-active {
+ tx {
+ pins = "gpio53";
+ function = "blsp_uart10";

- drive-strength = <2>;
- bias-pull-up;
- };
+ drive-strength = <2>;
+ bias-disable;
+ };

- cts {
- pins = "gpio55";
- function = "blsp_uart10";
+ rx {
+ pins = "gpio54";
+ function = "blsp_uart10";

- drive-strength = <2>;
- bias-pull-up;
- };
+ drive-strength = <2>;
+ bias-pull-up;
+ };

- rts {
- pins = "gpio56";
- function = "blsp_uart10";
+ cts {
+ pins = "gpio55";
+ function = "blsp_uart10";

- drive-strength = <2>;
- bias-disable;
- };
+ drive-strength = <2>;
+ bias-pull-up;
};
- };

- sdhci@f9824900 {
- status = "okay";
+ rts {
+ pins = "gpio56";
+ function = "blsp_uart10";

- vmmc-supply = <&pm8941_l20>;
- vqmmc-supply = <&pm8941_s3>;
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+};

- bus-width = <8>;
- non-removable;
+&mdss {
+ status = "okay";

- pinctrl-names = "default";
- pinctrl-0 = <&sdhc1_pin_a>;
+ mdp@fd900000 {
+ status = "okay";
};

- sdhci@f98a4900 {
+ dsi@fd922800 {
status = "okay";

- max-frequency = <100000000>;
- bus-width = <4>;
- non-removable;
- vmmc-supply = <&vreg_wlan>;
- vqmmc-supply = <&pm8941_s3>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&sdhc2_pin_a>;
+ vdda-supply = <&pm8941_l2>;
+ vdd-supply = <&pm8941_lvs3>;
+ vddio-supply = <&pm8941_l12>;

#address-cells = <1>;
#size-cells = <0>;

- bcrmf@1 {
- compatible = "brcm,bcm4339-fmac", "brcm,bcm4329-fmac";
- reg = <1>;
+ ports {
+ port@1 {
+ endpoint {
+ remote-endpoint = <&panel_in>;
+ data-lanes = <0 1 2 3>;
+ };
+ };
+ };

- brcm,drive-strength = <10>;
+ panel: panel@0 {
+ reg = <0>;
+ compatible = "lg,acx467akm-7";

pinctrl-names = "default";
- pinctrl-0 = <&wlan_sleep_clk_pin>;
+ pinctrl-0 = <&panel_pin>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&dsi0_out>;
+ };
+ };
};
};

- serial@f9960000 {
+ dsi-phy@fd922a00 {
status = "okay";

- pinctrl-names = "default";
- pinctrl-0 = <&blsp2_uart10_pin_a>;
+ vddio-supply = <&pm8941_l12>;
+ };
+};

- bluetooth {
- compatible = "brcm,bcm43438-bt";
- max-speed = <3000000>;
+&otg {
+ status = "okay";

- pinctrl-names = "default";
- pinctrl-0 = <&bt_pin>;
+ phys = <&usb_hs1_phy>;
+ phy-select = <&tcsr 0xb000 0>;

- host-wakeup-gpios = <&msmgpio 42 GPIO_ACTIVE_HIGH>;
- device-wakeup-gpios = <&msmgpio 62 GPIO_ACTIVE_HIGH>;
- shutdown-gpios = <&msmgpio 41 GPIO_ACTIVE_HIGH>;
- };
- };
+ extcon = <&charger>, <&usb_id>;
+ vbus-supply = <&usb_otg_vbus>;

- i2c@f9967000 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c11_pins>;
- clock-frequency = <355000>;
- qcom,src-freq = <50000000>;
+ hnp-disable;
+ srp-disable;
+ adp-disable;

- led-controller@38 {
- compatible = "ti,lm3630a";
+ ulpi {
+ phy@a {
status = "okay";
- reg = <0x38>;

- #address-cells = <1>;
- #size-cells = <0>;
+ v1p8-supply = <&pm8941_l6>;
+ v3p3-supply = <&pm8941_l24>;

- led@0 {
- reg = <0>;
- led-sources = <0 1>;
- label = "lcd-backlight";
- default-brightness = <200>;
- };
+ qcom,init-seq = /bits/ 8 <0x1 0x64>;
};
};
+};

- i2c@f9968000 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c12_pins>;
- clock-frequency = <100000>;
- qcom,src-freq = <50000000>;
+&rpm_requests {
+ pm8841-regulators {
+ s1 {
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <1050000>;
+ };

- mpu6515@68 {
- compatible = "invensense,mpu6515";
- reg = <0x68>;
- interrupts-extended = <&msmgpio 73 IRQ_TYPE_EDGE_FALLING>;
- vddio-supply = <&pm8941_lvs1>;
+ s2 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
+ };

- pinctrl-names = "default";
- pinctrl-0 = <&mpu6515_pin>;
-
- mount-matrix = "0", "-1", "0",
- "-1", "0", "0",
- "0", "0", "1";
-
- i2c-gate {
- #address-cells = <1>;
- #size-cells = <0>;
- ak8963@f {
- compatible = "asahi-kasei,ak8963";
- reg = <0x0f>;
- gpios = <&msmgpio 67 0>;
- vid-supply = <&pm8941_lvs1>;
- vdd-supply = <&pm8941_l17>;
- };
+ s3 {
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ };

- bmp280@76 {
- compatible = "bosch,bmp280";
- reg = <0x76>;
- vdda-supply = <&pm8941_lvs1>;
- vddd-supply = <&pm8941_l17>;
- };
- };
+ s4 {
+ regulator-min-microvolt = <815000>;
+ regulator-max-microvolt = <900000>;
};
};

- i2c@f9923000 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins>;
- clock-frequency = <100000>;
- qcom,src-freq = <50000000>;
-
- charger: bq24192@6b {
- compatible = "ti,bq24192";
- reg = <0x6b>;
- interrupts-extended = <&spmi_bus 0 0xd5 0 IRQ_TYPE_EDGE_FALLING>;
+ pm8941-regulators {
+ vdd_l1_l3-supply = <&pm8941_s1>;
+ vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+ vdd_l4_l11-supply = <&pm8941_s1>;
+ vdd_l5_l7-supply = <&pm8941_s2>;
+ vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+ vdd_l8_l16_l18_l19-supply = <&vreg_vph_pwr>;
+ vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
+ vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
+ vdd_l21-supply = <&vreg_boost>;
+
+ s1 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ };

- omit-battery-class;
+ s2 {
+ regulator-min-microvolt = <2150000>;
+ regulator-max-microvolt = <2150000>;

- usb_otg_vbus: usb-otg-vbus { };
+ regulator-boot-on;
};

- fuelgauge: max17048@36 {
- compatible = "maxim,max17048";
- reg = <0x36>;
+ s3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;

- maxim,double-soc;
- maxim,rcomp = /bits/ 8 <0x4d>;
+ regulator-always-on;
+ regulator-boot-on;
+ };

- interrupt-parent = <&msmgpio>;
- interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+ l1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;

- pinctrl-names = "default";
- pinctrl-0 = <&fuelgauge_pin>;
+ regulator-always-on;
+ regulator-boot-on;
+ };

- maxim,alert-low-soc-level = <2>;
+ l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
};
- };

- i2c@f9924000 {
- status = "okay";
+ l3 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };

- clock-frequency = <355000>;
- qcom,src-freq = <50000000>;
+ l4 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };

- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins>;
+ l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };

- synaptics@70 {
- compatible = "syna,rmi4-i2c";
- reg = <0x70>;
+ l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;

- interrupts-extended = <&msmgpio 5 IRQ_TYPE_EDGE_FALLING>;
- vdd-supply = <&pm8941_l22>;
- vio-supply = <&pm8941_lvs3>;
+ regulator-boot-on;
+ };

- pinctrl-names = "default";
- pinctrl-0 = <&touch_pin>;
+ l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;

- #address-cells = <1>;
- #size-cells = <0>;
+ regulator-boot-on;
+ };

- rmi4-f01@1 {
- reg = <0x1>;
- syna,nosleep-mode = <1>;
- };
+ l8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };

- rmi4-f12@12 {
- reg = <0x12>;
- syna,sensor-type = <1>;
- };
+ l9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
};
- };

- i2c@f9925000 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c3_pins>;
- clock-frequency = <100000>;
- qcom,src-freq = <50000000>;
+ l10 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };

- avago_apds993@39 {
- compatible = "avago,apds9930";
- reg = <0x39>;
- interrupts-extended = <&msmgpio 61 IRQ_TYPE_EDGE_FALLING>;
- vdd-supply = <&pm8941_l17>;
- vddio-supply = <&pm8941_lvs1>;
- led-max-microamp = <100000>;
- amstaos,proximity-diodes = <0>;
+ l11 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
};
- };

- usb@f9a55000 {
- status = "okay";
+ l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;

- phys = <&usb_hs1_phy>;
- phy-select = <&tcsr 0xb000 0>;
+ regulator-always-on;
+ regulator-boot-on;
+ };

- extcon = <&charger>, <&usb_id>;
- vbus-supply = <&usb_otg_vbus>;
+ l13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;

- hnp-disable;
- srp-disable;
- adp-disable;
+ regulator-boot-on;
+ };

- ulpi {
- phy@a {
- status = "okay";
+ l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };

- v1p8-supply = <&pm8941_l6>;
- v3p3-supply = <&pm8941_l24>;
+ l15 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };

- qcom,init-seq = /bits/ 8 <0x1 0x64>;
- };
+ l16 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
};
- };

- mdss@fd900000 {
- status = "okay";
+ l17 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };

- mdp@fd900000 {
- status = "okay";
+ l18 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
};

- dsi@fd922800 {
- status = "okay";
+ l19 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ };

- vdda-supply = <&pm8941_l2>;
- vdd-supply = <&pm8941_lvs3>;
- vddio-supply = <&pm8941_l12>;
+ l20 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;

- #address-cells = <1>;
- #size-cells = <0>;
+ regulator-boot-on;
+ regulator-system-load = <200000>;
+ regulator-allow-set-load;
+ };

- ports {
- port@1 {
- endpoint {
- remote-endpoint = <&panel_in>;
- data-lanes = <0 1 2 3>;
- };
- };
- };
+ l21 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;

- panel: panel@0 {
- reg = <0>;
- compatible = "lg,acx467akm-7";
+ regulator-boot-on;
+ };

- pinctrl-names = "default";
- pinctrl-0 = <&panel_pin>;
+ l22 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ };

- port {
- panel_in: endpoint {
- remote-endpoint = <&dsi0_out>;
- };
- };
- };
+ l23 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
};

- dsi-phy@fd922a00 {
- status = "okay";
+ l24 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;

- vddio-supply = <&pm8941_l12>;
+ regulator-boot-on;
};
};
};

+&sdhci1 {
+ status = "okay";
+
+ vmmc-supply = <&pm8941_l20>;
+ vqmmc-supply = <&pm8941_s3>;
+
+ bus-width = <8>;
+ non-removable;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc1_pin_a>;
+};
+
+&sdhci3 {
+ status = "okay";
+
+ max-frequency = <100000000>;
+ bus-width = <4>;
+ non-removable;
+ vmmc-supply = <&vreg_wlan>;
+ vqmmc-supply = <&pm8941_s3>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc2_pin_a>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bcrmf@1 {
+ compatible = "brcm,bcm4339-fmac", "brcm,bcm4329-fmac";
+ reg = <1>;
+
+ brcm,drive-strength = <10>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&wlan_sleep_clk_pin>;
+ };
+};
+
&spmi_bus {
pm8941@0 {
gpios@c000 {
diff --git a/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts b/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts
index 6e036a440532..ffa31625de17 100644
--- a/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts
@@ -12,8 +12,8 @@ / {

aliases {
serial0 = &blsp1_uart1;
- mmc0 = &sdhc_1; /* SDC1 eMMC slot */
- mmc1 = &sdhc_2; /* SDC2 SD card slot */
+ mmc0 = &sdhci1; /* SDC1 eMMC slot */
+ mmc1 = &sdhci2; /* SDC2 SD card slot */
};

chosen {
@@ -52,197 +52,6 @@ volume-up {
};
};

- smd {
- rpm {
- rpm_requests {
- pma8084-regulators {
- compatible = "qcom,rpm-pma8084-regulators";
- status = "okay";
-
- pma8084_s1: s1 {
- regulator-min-microvolt = <675000>;
- regulator-max-microvolt = <1050000>;
- regulator-always-on;
- };
-
- pma8084_s2: s2 {
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <1050000>;
- };
-
- pma8084_s3: s3 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- };
-
- pma8084_s4: s4 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- pma8084_s5: s5 {
- regulator-min-microvolt = <2150000>;
- regulator-max-microvolt = <2150000>;
- };
-
- pma8084_s6: s6 {
- regulator-min-microvolt = <1050000>;
- regulator-max-microvolt = <1050000>;
- };
-
- pma8084_l1: l1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- pma8084_l2: l2 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- pma8084_l3: l3 {
- regulator-min-microvolt = <1050000>;
- regulator-max-microvolt = <1200000>;
- };
-
- pma8084_l4: l4 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1225000>;
- };
-
- pma8084_l5: l5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- pma8084_l6: l6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- pma8084_l7: l7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- pma8084_l8: l8 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- pma8084_l9: l9 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- pma8084_l10: l10 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- pma8084_l11: l11 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- };
-
- pma8084_l12: l12 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- pma8084_l13: l13 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- pma8084_l14: l14 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- pma8084_l15: l15 {
- regulator-min-microvolt = <2050000>;
- regulator-max-microvolt = <2050000>;
- };
-
- pma8084_l16: l16 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-
- pma8084_l17: l17 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- pma8084_l18: l18 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- pma8084_l19: l19 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- pma8084_l20: l20 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-allow-set-load;
- regulator-system-load = <200000>;
- };
-
- pma8084_l21: l21 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-allow-set-load;
- regulator-system-load = <200000>;
- };
-
- pma8084_l22: l22 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3300000>;
- };
-
- pma8084_l23: l23 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- pma8084_l24: l24 {
- regulator-min-microvolt = <3075000>;
- regulator-max-microvolt = <3075000>;
- };
-
- pma8084_l25: l25 {
- regulator-min-microvolt = <2100000>;
- regulator-max-microvolt = <2100000>;
- };
-
- pma8084_l26: l26 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2050000>;
- };
-
- pma8084_l27: l27 {
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1225000>;
- };
-
- pma8084_lvs1: lvs1 {};
- pma8084_lvs2: lvs2 {};
- pma8084_lvs3: lvs3 {};
- pma8084_lvs4: lvs4 {};
-
- pma8084_5vs1: 5vs1 {};
- };
- };
- };
- };
-
i2c-gpio-touchkey {
compatible = "i2c-gpio";
#address-cells = <1>;
@@ -353,493 +162,677 @@ adsp-pil {
};
};

-&soc {
- serial@f991e000 {
- status = "okay";
- };
+&blsp_i2c2 {
+ status = "okay";

- /* blsp2_uart8 */
- serial@f995e000 {
- status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;

- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&blsp2_uart8_pins_active>;
- pinctrl-1 = <&blsp2_uart8_pins_sleep>;
+ touchscreen@20 {
+ compatible = "syna,rmi4-i2c";
+ reg = <0x20>;

- bluetooth {
- compatible = "brcm,bcm43540-bt";
- max-speed = <3000000>;
- pinctrl-names = "default";
- pinctrl-0 = <&bt_pins>;
- device-wakeup-gpios = <&msmgpio 91 GPIO_ACTIVE_HIGH>;
- shutdown-gpios = <&gpio_expander 9 GPIO_ACTIVE_HIGH>;
- interrupt-parent = <&msmgpio>;
- interrupts = <75 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "host-wakeup";
- };
- };
+ interrupt-parent = <&pma8084_gpios>;
+ interrupts = <8 IRQ_TYPE_EDGE_FALLING>;

- pinctrl@fd510000 {
- blsp2_uart8_pins_active: blsp2-uart8-pins-active {
- pins = "gpio45", "gpio46", "gpio47", "gpio48";
- function = "blsp_uart8";
- drive-strength = <8>;
- bias-disable;
+ vdd-supply = <&max77826_ldo13>;
+ vio-supply = <&pma8084_lvs2>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&touch_pin>;
+
+ syna,startup-delay-ms = <100>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rmi4-f01@1 {
+ reg = <0x1>;
+ syna,nosleep-mode = <1>;
};

- blsp2_uart8_pins_sleep: blsp2-uart8-pins-sleep {
- pins = "gpio45", "gpio46", "gpio47", "gpio48";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-down;
+ rmi4-f12@12 {
+ reg = <0x12>;
+ syna,sensor-type = <1>;
};
+ };
+};

- bt_pins: bt-pins {
- hostwake {
- pins = "gpio75";
- function = "gpio";
- drive-strength = <16>;
- input-enable;
+&blsp_i2c6 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c6_pins>;
+
+ pmic@60 {
+ reg = <0x60>;
+ compatible = "maxim,max77826";
+
+ regulators {
+ max77826_ldo1: LDO1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
};

- devwake {
- pins = "gpio91";
- function = "gpio";
- drive-strength = <2>;
+ max77826_ldo2: LDO2 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
};
- };

- sdhc1_pin_a: sdhc1-pin-active {
- clk {
- pins = "sdc1_clk";
- drive-strength = <4>;
- bias-disable;
+ max77826_ldo3: LDO3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
};

- cmd-data {
- pins = "sdc1_cmd", "sdc1_data";
- drive-strength = <4>;
- bias-pull-up;
+ max77826_ldo4: LDO4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
};
- };

- sdhc2_pin_a: sdhc2-pin-active {
- clk-cmd-data {
- pins = "gpio35", "gpio36", "gpio37", "gpio38",
- "gpio39", "gpio40";
- function = "sdc3";
- drive-strength = <8>;
- bias-disable;
+ max77826_ldo5: LDO5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
};
- };

- sdhc2_cd_pin: sdhc2-cd {
- pins = "gpio62";
- function = "gpio";
+ max77826_ldo6: LDO6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };

- drive-strength = <2>;
- bias-disable;
- };
+ max77826_ldo7: LDO7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };

- sdhc3_pin_a: sdhc3-pin-active {
- clk {
- pins = "sdc2_clk";
- drive-strength = <6>;
- bias-disable;
+ max77826_ldo8: LDO8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
};

- cmd-data {
- pins = "sdc2_cmd", "sdc2_data";
- drive-strength = <6>;
- bias-pull-up;
+ max77826_ldo9: LDO9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
};
- };

- i2c2_pins: i2c2 {
- mux {
- pins = "gpio6", "gpio7";
- function = "blsp_i2c2";
+ max77826_ldo10: LDO10 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2950000>;
+ };

- drive-strength = <2>;
- bias-disable;
+ max77826_ldo11: LDO11 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2950000>;
};
- };

- i2c6_pins: i2c6 {
- mux {
- pins = "gpio29", "gpio30";
- function = "blsp_i2c6";
+ max77826_ldo12: LDO12 {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <3300000>;
+ };

- drive-strength = <2>;
- bias-disable;
+ max77826_ldo13: LDO13 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
};
- };

- i2c12_pins: i2c12 {
- mux {
- pins = "gpio87", "gpio88";
- function = "blsp_i2c12";
+ max77826_ldo14: LDO14 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };

- drive-strength = <2>;
- bias-disable;
+ max77826_ldo15: LDO15 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
};
- };

- i2c_touchkey_pins: i2c-touchkey {
- mux {
- pins = "gpio95", "gpio96";
- function = "gpio";
- input-enable;
- bias-pull-up;
+ max77826_buck: BUCK {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
};
- };

- i2c_led_gpioex_pins: i2c-led-gpioex {
- mux {
- pins = "gpio120", "gpio121";
- function = "gpio";
- input-enable;
- bias-pull-down;
+ max77826_buckboost: BUCKBOOST {
+ regulator-min-microvolt = <3400000>;
+ regulator-max-microvolt = <3400000>;
};
};
+ };
+};

- gpioex_pin: gpioex {
- res {
- pins = "gpio145";
- function = "gpio";
+&blsp_i2c12 {
+ status = "okay";

- bias-pull-up;
- drive-strength = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c12_pins>;
+
+ fuelgauge@36 {
+ compatible = "maxim,max17048";
+ reg = <0x36>;
+
+ maxim,double-soc;
+ maxim,rcomp = /bits/ 8 <0x56>;
+
+ interrupt-parent = <&pma8084_gpios>;
+ interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&fuelgauge_pin>;
+ };
+};
+
+&blsp1_uart2 {
+ status = "okay";
+};
+
+&blsp2_uart8 {
+ status = "okay";
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&blsp2_uart8_pins_active>;
+ pinctrl-1 = <&blsp2_uart8_pins_sleep>;
+
+ bluetooth {
+ compatible = "brcm,bcm43540-bt";
+ max-speed = <3000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_pins>;
+ device-wakeup-gpios = <&msmgpio 91 GPIO_ACTIVE_HIGH>;
+ shutdown-gpios = <&gpio_expander 9 GPIO_ACTIVE_HIGH>;
+ interrupt-parent = <&msmgpio>;
+ interrupts = <75 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "host-wakeup";
+ };
+};
+
+&gpu {
+ status = "ok";
+};
+
+&mdss {
+ status = "ok";
+
+ mdp@fd900000 {
+ status = "ok";
+ };
+
+ dsi@fd922800 {
+ status = "ok";
+
+ vdda-supply = <&pma8084_l2>;
+ vdd-supply = <&pma8084_l22>;
+ vddio-supply = <&pma8084_l12>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ports {
+ port@1 {
+ endpoint {
+ remote-endpoint = <&panel_in>;
+ data-lanes = <0 1 2 3>;
+ };
};
};

- wifi_pin: wifi {
- int {
- pins = "gpio92";
- function = "gpio";
+ panel: panel@0 {
+ reg = <0>;
+ compatible = "samsung,s6e3fa2";

- input-enable;
- bias-pull-down;
+ pinctrl-names = "default";
+ pinctrl-0 = <&panel_te_pin &panel_rst_pin>;
+
+ iovdd-supply = <&pma8084_lvs4>;
+ vddr-supply = <&vreg_panel>;
+
+ reset-gpios = <&pma8084_gpios 17 GPIO_ACTIVE_LOW>;
+ te-gpios = <&msmgpio 12 GPIO_ACTIVE_HIGH>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&dsi0_out>;
+ };
};
};
+ };

- panel_te_pin: panel {
- te {
- pins = "gpio12";
- function = "mdp_vsync";
+ dsi-phy@fd922a00 {
+ status = "ok";

- drive-strength = <2>;
- bias-disable;
- };
+ vddio-supply = <&pma8084_l12>;
+ };
+};
+
+&msmgpio {
+ blsp2_uart8_pins_active: blsp2-uart8-pins-active {
+ pins = "gpio45", "gpio46", "gpio47", "gpio48";
+ function = "blsp_uart8";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ blsp2_uart8_pins_sleep: blsp2-uart8-pins-sleep {
+ pins = "gpio45", "gpio46", "gpio47", "gpio48";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ bt_pins: bt-pins {
+ hostwake {
+ pins = "gpio75";
+ function = "gpio";
+ drive-strength = <16>;
+ input-enable;
+ };
+
+ devwake {
+ pins = "gpio91";
+ function = "gpio";
+ drive-strength = <2>;
};
};

- sdhc_1: sdhci@f9824900 {
- status = "okay";
+ sdhc1_pin_a: sdhc1-pin-active {
+ clk {
+ pins = "sdc1_clk";
+ drive-strength = <4>;
+ bias-disable;
+ };
+
+ cmd-data {
+ pins = "sdc1_cmd", "sdc1_data";
+ drive-strength = <4>;
+ bias-pull-up;
+ };
+ };

- vmmc-supply = <&pma8084_l20>;
- vqmmc-supply = <&pma8084_s4>;
+ sdhc2_pin_a: sdhc2-pin-active {
+ clk-cmd-data {
+ pins = "gpio35", "gpio36", "gpio37", "gpio38",
+ "gpio39", "gpio40";
+ function = "sdc3";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };

- bus-width = <8>;
- non-removable;
+ sdhc2_cd_pin: sdhc2-cd {
+ pins = "gpio62";
+ function = "gpio";

- pinctrl-names = "default";
- pinctrl-0 = <&sdhc1_pin_a>;
+ drive-strength = <2>;
+ bias-disable;
};

- sdhc_2: sdhci@f9864900 {
- status = "okay";
+ sdhc3_pin_a: sdhc3-pin-active {
+ clk {
+ pins = "sdc2_clk";
+ drive-strength = <6>;
+ bias-disable;
+ };
+
+ cmd-data {
+ pins = "sdc2_cmd", "sdc2_data";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+ };

- max-frequency = <100000000>;
+ i2c2_pins: i2c2 {
+ mux {
+ pins = "gpio6", "gpio7";
+ function = "blsp_i2c2";

- vmmc-supply = <&pma8084_l21>;
- vqmmc-supply = <&pma8084_l13>;
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };

- bus-width = <4>;
+ i2c6_pins: i2c6 {
+ mux {
+ pins = "gpio29", "gpio30";
+ function = "blsp_i2c6";

- /* cd-gpio is intentionally disabled. If enabled, an SD card
- * present during boot is not initialized correctly. Without
- * cd-gpios the driver resorts to polling, so hotplug works.
- */
- pinctrl-names = "default";
- pinctrl-0 = <&sdhc2_pin_a /* &sdhc2_cd_pin */>;
- // cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
+ drive-strength = <2>;
+ bias-disable;
+ };
};

- sdhci@f98a4900 {
- status = "okay";
+ i2c12_pins: i2c12 {
+ mux {
+ pins = "gpio87", "gpio88";
+ function = "blsp_i2c12";

- #address-cells = <1>;
- #size-cells = <0>;
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };

- max-frequency = <100000000>;
+ i2c_touchkey_pins: i2c-touchkey {
+ mux {
+ pins = "gpio95", "gpio96";
+ function = "gpio";
+ input-enable;
+ bias-pull-up;
+ };
+ };

- pinctrl-names = "default";
- pinctrl-0 = <&sdhc3_pin_a>;
+ i2c_led_gpioex_pins: i2c-led-gpioex {
+ mux {
+ pins = "gpio120", "gpio121";
+ function = "gpio";
+ input-enable;
+ bias-pull-down;
+ };
+ };

- vmmc-supply = <&vreg_wlan>;
- vqmmc-supply = <&pma8084_s4>;
+ gpioex_pin: gpioex {
+ res {
+ pins = "gpio145";
+ function = "gpio";

- bus-width = <4>;
- non-removable;
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+ };

- wifi@1 {
- reg = <1>;
- compatible = "brcm,bcm4329-fmac";
+ wifi_pin: wifi {
+ int {
+ pins = "gpio92";
+ function = "gpio";

- interrupt-parent = <&msmgpio>;
- interrupts = <92 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "host-wake";
+ input-enable;
+ bias-pull-down;
+ };
+ };

- pinctrl-names = "default";
- pinctrl-0 = <&wlan_sleep_clk_pin &wifi_pin>;
+ panel_te_pin: panel {
+ te {
+ pins = "gpio12";
+ function = "mdp_vsync";
+
+ drive-strength = <2>;
+ bias-disable;
};
};
+};

- usb@f9a55000 {
- status = "okay";
+&mss_pil {
+ cx-supply = <&pma8084_s2>;
+ mss-supply = <&pma8084_s6>;
+ mx-supply = <&pma8084_s1>;
+ pll-supply = <&pma8084_l12>;
+};

- phys = <&usb_hs1_phy>;
- phy-select = <&tcsr 0xb000 0>;
- /*extcon = <&smbb>, <&usb_id>;*/
- /*vbus-supply = <&chg_otg>;*/
+&otg {
+ status = "okay";

- hnp-disable;
- srp-disable;
- adp-disable;
+ phys = <&usb_hs1_phy>;
+ phy-select = <&tcsr 0xb000 0>;
+ /*extcon = <&smbb>, <&usb_id>;*/
+ /*vbus-supply = <&chg_otg>;*/

- ulpi {
- phy@a {
- status = "okay";
+ hnp-disable;
+ srp-disable;
+ adp-disable;

- v1p8-supply = <&pma8084_l6>;
- v3p3-supply = <&pma8084_l24>;
+ ulpi {
+ phy@a {
+ status = "okay";

- /*extcon = <&smbb>;*/
- qcom,init-seq = /bits/ 8 <0x1 0x64>;
- };
+ v1p8-supply = <&pma8084_l6>;
+ v3p3-supply = <&pma8084_l24>;
+
+ /*extcon = <&smbb>;*/
+ qcom,init-seq = /bits/ 8 <0x1 0x64>;
};
};
+};

- i2c@f9924000 {
+&rpm_requests {
+ pma8084-regulators {
+ compatible = "qcom,rpm-pma8084-regulators";
status = "okay";

- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins>;
+ pma8084_s1: s1 {
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-always-on;
+ };

- touchscreen@20 {
- compatible = "syna,rmi4-i2c";
- reg = <0x20>;
+ pma8084_s2: s2 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
+ };

- interrupt-parent = <&pma8084_gpios>;
- interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
+ pma8084_s3: s3 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ };

- vdd-supply = <&max77826_ldo13>;
- vio-supply = <&pma8084_lvs2>;
+ pma8084_s4: s4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };

- pinctrl-names = "default";
- pinctrl-0 = <&touch_pin>;
+ pma8084_s5: s5 {
+ regulator-min-microvolt = <2150000>;
+ regulator-max-microvolt = <2150000>;
+ };

- syna,startup-delay-ms = <100>;
+ pma8084_s6: s6 {
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ };

- #address-cells = <1>;
- #size-cells = <0>;
+ pma8084_l1: l1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };

- rmi4-f01@1 {
- reg = <0x1>;
- syna,nosleep-mode = <1>;
- };
+ pma8084_l2: l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };

- rmi4-f12@12 {
- reg = <0x12>;
- syna,sensor-type = <1>;
- };
+ pma8084_l3: l3 {
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1200000>;
};
- };

- i2c@f9928000 {
- status = "okay";
+ pma8084_l4: l4 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1225000>;
+ };

- pinctrl-names = "default";
- pinctrl-0 = <&i2c6_pins>;
+ pma8084_l5: l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };

- pmic@60 {
- reg = <0x60>;
- compatible = "maxim,max77826";
+ pma8084_l6: l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };

- regulators {
- max77826_ldo1: LDO1 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
+ pma8084_l7: l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };

- max77826_ldo2: LDO2 {
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- };
+ pma8084_l8: l8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };

- max77826_ldo3: LDO3 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
+ pma8084_l9: l9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };

- max77826_ldo4: LDO4 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
+ pma8084_l10: l10 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };

- max77826_ldo5: LDO5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
+ pma8084_l11: l11 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ };

- max77826_ldo6: LDO6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
+ pma8084_l12: l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };

- max77826_ldo7: LDO7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
+ pma8084_l13: l13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };

- max77826_ldo8: LDO8 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
+ pma8084_l14: l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };

- max77826_ldo9: LDO9 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
+ pma8084_l15: l15 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };

- max77826_ldo10: LDO10 {
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2950000>;
- };
+ pma8084_l16: l16 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };

- max77826_ldo11: LDO11 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2950000>;
- };
+ pma8084_l17: l17 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };

- max77826_ldo12: LDO12 {
- regulator-min-microvolt = <2500000>;
- regulator-max-microvolt = <3300000>;
- };
+ pma8084_l18: l18 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };

- max77826_ldo13: LDO13 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
+ pma8084_l19: l19 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };

- max77826_ldo14: LDO14 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
+ pma8084_l20: l20 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;

- max77826_ldo15: LDO15 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
+ regulator-allow-set-load;
+ regulator-system-load = <200000>;
+ };

- max77826_buck: BUCK {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
+ pma8084_l21: l21 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;

- max77826_buckboost: BUCKBOOST {
- regulator-min-microvolt = <3400000>;
- regulator-max-microvolt = <3400000>;
- };
- };
+ regulator-allow-set-load;
+ regulator-system-load = <200000>;
};
- };

- i2c@f9968000 {
- status = "okay";
+ pma8084_l22: l22 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ };

- pinctrl-names = "default";
- pinctrl-0 = <&i2c12_pins>;
+ pma8084_l23: l23 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };

- fuelgauge@36 {
- compatible = "maxim,max17048";
- reg = <0x36>;
+ pma8084_l24: l24 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+ };

- maxim,double-soc;
- maxim,rcomp = /bits/ 8 <0x56>;
+ pma8084_l25: l25 {
+ regulator-min-microvolt = <2100000>;
+ regulator-max-microvolt = <2100000>;
+ };

- interrupt-parent = <&pma8084_gpios>;
- interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
+ pma8084_l26: l26 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2050000>;
+ };

- pinctrl-names = "default";
- pinctrl-0 = <&fuelgauge_pin>;
+ pma8084_l27: l27 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1225000>;
};
- };

- adreno@fdb00000 {
- status = "ok";
+ pma8084_lvs1: lvs1 {};
+ pma8084_lvs2: lvs2 {};
+ pma8084_lvs3: lvs3 {};
+ pma8084_lvs4: lvs4 {};
+
+ pma8084_5vs1: 5vs1 {};
};
+};

- mdss@fd900000 {
- status = "ok";
+&sdhci1 {
+ status = "okay";

- mdp@fd900000 {
- status = "ok";
- };
+ vmmc-supply = <&pma8084_l20>;
+ vqmmc-supply = <&pma8084_s4>;
+
+ bus-width = <8>;
+ non-removable;

- dsi@fd922800 {
- status = "ok";
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc1_pin_a>;
+};

- vdda-supply = <&pma8084_l2>;
- vdd-supply = <&pma8084_l22>;
- vddio-supply = <&pma8084_l12>;
+&sdhci2 {
+ status = "okay";

- #address-cells = <1>;
- #size-cells = <0>;
+ max-frequency = <100000000>;

- ports {
- port@1 {
- endpoint {
- remote-endpoint = <&panel_in>;
- data-lanes = <0 1 2 3>;
- };
- };
- };
+ vmmc-supply = <&pma8084_l21>;
+ vqmmc-supply = <&pma8084_l13>;

- panel: panel@0 {
- reg = <0>;
- compatible = "samsung,s6e3fa2";
+ bus-width = <4>;

- pinctrl-names = "default";
- pinctrl-0 = <&panel_te_pin &panel_rst_pin>;
+ /* cd-gpio is intentionally disabled. If enabled, an SD card
+ * present during boot is not initialized correctly. Without
+ * cd-gpios the driver resorts to polling, so hotplug works.
+ */
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc2_pin_a /* &sdhc2_cd_pin */>;
+ // cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
+};

- iovdd-supply = <&pma8084_lvs4>;
- vddr-supply = <&vreg_panel>;
+&sdhci3 {
+ status = "okay";

- reset-gpios = <&pma8084_gpios 17 GPIO_ACTIVE_LOW>;
- te-gpios = <&msmgpio 12 GPIO_ACTIVE_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;

- port {
- panel_in: endpoint {
- remote-endpoint = <&dsi0_out>;
- };
- };
- };
- };
+ max-frequency = <100000000>;

- dsi-phy@fd922a00 {
- status = "ok";
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc3_pin_a>;

- vddio-supply = <&pma8084_l12>;
- };
- };
+ vmmc-supply = <&vreg_wlan>;
+ vqmmc-supply = <&pma8084_s4>;

- remoteproc@fc880000 {
- cx-supply = <&pma8084_s2>;
- mss-supply = <&pma8084_s6>;
- mx-supply = <&pma8084_s1>;
- pll-supply = <&pma8084_l12>;
+ bus-width = <4>;
+ non-removable;
+
+ wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+
+ interrupt-parent = <&msmgpio>;
+ interrupts = <92 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "host-wake";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&wlan_sleep_clk_pin &wifi_pin>;
};
};

diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-amami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-amami.dts
index 79e2cfbbb1ba..4f28ca3340de 100644
--- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-amami.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-amami.dts
@@ -57,339 +57,332 @@ memory@0 {
reg = <0 0x40000000>, <0x40000000 0x40000000>;
device_type = "memory";
};
+};

- smd {
- rpm {
- rpm_requests {
- pm8841-regulators {
- s1 {
- regulator-min-microvolt = <675000>;
- regulator-max-microvolt = <1050000>;
- };
-
- s2 {
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <1050000>;
- };
-
- s3 {
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <1050000>;
- };
-
- s4 {
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <1050000>;
- };
- };
-
- pm8941-regulators {
- vdd_l1_l3-supply = <&pm8941_s1>;
- vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
- vdd_l4_l11-supply = <&pm8941_s1>;
- vdd_l5_l7-supply = <&pm8941_s2>;
- vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
- vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
- vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
- vdd_l21-supply = <&vreg_boost>;
-
- s1 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- s2 {
- regulator-min-microvolt = <2150000>;
- regulator-max-microvolt = <2150000>;
- regulator-boot-on;
- };
-
- s3 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- s4 {
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- };
-
- l1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- l2 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l3 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l4 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-boot-on;
- };
-
- l7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-boot-on;
- };
-
- l8 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l9 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l11 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1350000>;
- };
-
- l12 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- l13 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-boot-on;
- };
-
- l14 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l15 {
- regulator-min-microvolt = <2050000>;
- regulator-max-microvolt = <2050000>;
- };
-
- l16 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-
- l17 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-
- l18 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- l19 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l20 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-allow-set-load;
- regulator-boot-on;
- regulator-system-load = <200000>;
- };
-
- l21 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-boot-on;
- };
-
- l22 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- l23 {
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- l24 {
- regulator-min-microvolt = <3075000>;
- regulator-max-microvolt = <3075000>;
-
- regulator-boot-on;
- };
- };
- };
+&blsp1_uart2 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_uart2_pin_a>;
+};
+
+&blsp2_dma {
+ qcom,controlled-remotely;
+};
+
+&msmgpio {
+ blsp1_uart2_pin_a: blsp1-uart2-pin-active {
+ rx {
+ pins = "gpio5";
+ function = "blsp_uart2";
+
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ tx {
+ pins = "gpio4";
+ function = "blsp_uart2";
+
+ drive-strength = <4>;
+ bias-disable;
};
};
-};

-&soc {
- sdhci@f9824900 {
- status = "okay";
+ i2c2_pins: i2c2 {
+ mux {
+ pins = "gpio6", "gpio7";
+ function = "blsp_i2c2";

- vmmc-supply = <&pm8941_l20>;
- vqmmc-supply = <&pm8941_s3>;
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };

- bus-width = <8>;
- non-removable;
+ sdhc1_pin_a: sdhc1-pin-active {
+ clk {
+ pins = "sdc1_clk";
+ drive-strength = <16>;
+ bias-disable;
+ };

- pinctrl-names = "default";
- pinctrl-0 = <&sdhc1_pin_a>;
+ cmd-data {
+ pins = "sdc1_cmd", "sdc1_data";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
};

- sdhci@f98a4900 {
- status = "okay";
+ sdhc2_cd_pin_a: sdhc2-cd-pin-active {
+ pins = "gpio62";
+ function = "gpio";

- bus-width = <4>;
+ drive-strength = <2>;
+ bias-disable;
+ };

- vmmc-supply = <&pm8941_l21>;
- vqmmc-supply = <&pm8941_l13>;
+ sdhc2_pin_a: sdhc2-pin-active {
+ clk {
+ pins = "sdc2_clk";
+ drive-strength = <10>;
+ bias-disable;
+ };

- cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
+ cmd-data {
+ pins = "sdc2_cmd", "sdc2_data";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+ };
+};

- pinctrl-names = "default";
- pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
+&otg {
+ status = "okay";
+
+ phys = <&usb_hs1_phy>;
+ phy-select = <&tcsr 0xb000 0>;
+ extcon = <&smbb>, <&usb_id>;
+ vbus-supply = <&chg_otg>;
+
+ hnp-disable;
+ srp-disable;
+ adp-disable;
+
+ ulpi {
+ phy@a {
+ status = "okay";
+
+ v1p8-supply = <&pm8941_l6>;
+ v3p3-supply = <&pm8941_l24>;
+
+ extcon = <&smbb>;
+ qcom,init-seq = /bits/ 8 <0x1 0x64>;
+ };
};
+};
+
+&rpm_requests {
+ pm8841-regulators {
+ s1 {
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <1050000>;
+ };

- serial@f991e000 {
- status = "okay";
+ s2 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
+ };

- pinctrl-names = "default";
- pinctrl-0 = <&blsp1_uart2_pin_a>;
+ s3 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
+ };
+
+ s4 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
+ };
};

+ pm8941-regulators {
+ vdd_l1_l3-supply = <&pm8941_s1>;
+ vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+ vdd_l4_l11-supply = <&pm8941_s1>;
+ vdd_l5_l7-supply = <&pm8941_s2>;
+ vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+ vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
+ vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
+ vdd_l21-supply = <&vreg_boost>;
+
+ s1 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };

- pinctrl@fd510000 {
- blsp1_uart2_pin_a: blsp1-uart2-pin-active {
- rx {
- pins = "gpio5";
- function = "blsp_uart2";
+ s2 {
+ regulator-min-microvolt = <2150000>;
+ regulator-max-microvolt = <2150000>;
+ regulator-boot-on;
+ };

- drive-strength = <2>;
- bias-pull-up;
- };
+ s3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };

- tx {
- pins = "gpio4";
- function = "blsp_uart2";
+ s4 {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };

- drive-strength = <4>;
- bias-disable;
- };
+ l1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+
+ regulator-always-on;
+ regulator-boot-on;
};

- i2c2_pins: i2c2 {
- mux {
- pins = "gpio6", "gpio7";
- function = "blsp_i2c2";
+ l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };

- drive-strength = <2>;
- bias-disable;
- };
+ l3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
};

- sdhc1_pin_a: sdhc1-pin-active {
- clk {
- pins = "sdc1_clk";
- drive-strength = <16>;
- bias-disable;
- };
+ l4 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };

- cmd-data {
- pins = "sdc1_cmd", "sdc1_data";
- drive-strength = <10>;
- bias-pull-up;
- };
+ l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
};

- sdhc2_cd_pin_a: sdhc2-cd-pin-active {
- pins = "gpio62";
- function = "gpio";
+ l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;

- drive-strength = <2>;
- bias-disable;
- };
+ regulator-boot-on;
+ };

- sdhc2_pin_a: sdhc2-pin-active {
- clk {
- pins = "sdc2_clk";
- drive-strength = <10>;
- bias-disable;
- };
+ l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;

- cmd-data {
- pins = "sdc2_cmd", "sdc2_data";
- drive-strength = <6>;
- bias-pull-up;
- };
+ regulator-boot-on;
};
- };

- dma-controller@f9944000 {
- qcom,controlled-remotely;
- };
+ l8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };

- usb@f9a55000 {
- status = "okay";
+ l9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };

- phys = <&usb_hs1_phy>;
- phy-select = <&tcsr 0xb000 0>;
- extcon = <&smbb>, <&usb_id>;
- vbus-supply = <&chg_otg>;
+ l11 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1350000>;
+ };

- hnp-disable;
- srp-disable;
- adp-disable;
+ l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;

- ulpi {
- phy@a {
- status = "okay";
+ regulator-always-on;
+ regulator-boot-on;
+ };

- v1p8-supply = <&pm8941_l6>;
- v3p3-supply = <&pm8941_l24>;
+ l13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;

- extcon = <&smbb>;
- qcom,init-seq = /bits/ 8 <0x1 0x64>;
- };
+ regulator-boot-on;
+ };
+
+ l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l15 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };
+
+ l16 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ l17 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ l18 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ l19 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ l20 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-allow-set-load;
+ regulator-boot-on;
+ regulator-system-load = <200000>;
+ };
+
+ l21 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-boot-on;
+ };
+
+ l22 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ l23 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ l24 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+
+ regulator-boot-on;
};
};
};

+&sdhci1 {
+ status = "okay";
+
+ vmmc-supply = <&pm8941_l20>;
+ vqmmc-supply = <&pm8941_s3>;
+
+ bus-width = <8>;
+ non-removable;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc1_pin_a>;
+};
+
+&sdhci3 {
+ status = "okay";
+
+ bus-width = <4>;
+
+ vmmc-supply = <&pm8941_l21>;
+ vqmmc-supply = <&pm8941_l13>;
+
+ cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
+};
+
&spmi_bus {
pm8941@0 {
charger@1000 {
diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-castor.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-castor.dts
index e66937e3f7dd..f4b537294fb4 100644
--- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-castor.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-castor.dts
@@ -53,186 +53,6 @@ volume-up {
};
};

- smd {
- rpm {
- rpm_requests {
- pm8941-regulators {
- vdd_l1_l3-supply = <&pm8941_s1>;
- vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
- vdd_l4_l11-supply = <&pm8941_s1>;
- vdd_l5_l7-supply = <&pm8941_s2>;
- vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
- vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
- vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
- vdd_l21-supply = <&vreg_boost>;
-
- s1 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- s2 {
- regulator-min-microvolt = <2150000>;
- regulator-max-microvolt = <2150000>;
- regulator-boot-on;
- };
-
- s3 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
-
- regulator-system-load = <154000>;
- };
-
- s4 {
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- };
-
- l1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- l2 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l3 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l4 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-boot-on;
- };
-
- l7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-boot-on;
- };
-
- l8 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l9 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l11 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1350000>;
- };
-
- l12 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- l13 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-boot-on;
- };
-
- l14 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l15 {
- regulator-min-microvolt = <2050000>;
- regulator-max-microvolt = <2050000>;
- };
-
- l16 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-
- l17 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-
- l18 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- l19 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- l20 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-allow-set-load;
- regulator-boot-on;
- regulator-allow-set-load;
- regulator-system-load = <500000>;
- };
-
- l21 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-boot-on;
- };
-
- l22 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- l23 {
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- l24 {
- regulator-min-microvolt = <3075000>;
- regulator-max-microvolt = <3075000>;
-
- regulator-boot-on;
- };
- };
- };
- };
- };
-
vreg_bl_vddio: lcd-backlight-vddio {
compatible = "regulator-fixed";
regulator-name = "vreg_bl_vddio";
@@ -277,385 +97,559 @@ vreg_wlan: wlan-regulator {
};
};

-&soc {
- sdhci@f9824900 {
- status = "okay";
+&blsp_i2c8 {
+ status = "okay";

- vmmc-supply = <&pm8941_l20>;
- vqmmc-supply = <&pm8941_s3>;
+ clock-frequency = <355000>;
+ qcom,src-freq = <50000000>;

- bus-width = <8>;
- non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c8_pins>;

- pinctrl-names = "default";
- pinctrl-0 = <&sdhc1_pin_a>;
- };
+ synaptics@2c {
+ compatible = "syna,rmi4-i2c";
+ reg = <0x2c>;

- sdhci@f9864900 {
- status = "okay";
+ interrupt-parent = <&msmgpio>;
+ interrupts = <86 IRQ_TYPE_EDGE_FALLING>;

- max-frequency = <100000000>;
- non-removable;
- vmmc-supply = <&vreg_wlan>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ vdd-supply = <&pm8941_l22>;
+ vio-supply = <&pm8941_lvs3>;

pinctrl-names = "default";
- pinctrl-0 = <&sdhc3_pin_a>;
+ pinctrl-0 = <&ts_int_pin>;

- #address-cells = <1>;
- #size-cells = <0>;
+ syna,startup-delay-ms = <10>;

- bcrmf@1 {
- compatible = "brcm,bcm4339-fmac", "brcm,bcm4329-fmac";
- reg = <1>;
+ rmi-f01@1 {
+ reg = <0x1>;
+ syna,nosleep = <1>;
+ };

- brcm,drive-strength = <10>;
+ rmi-f11@11 {
+ reg = <0x11>;
+ syna,f11-flip-x = <1>;
+ syna,sensor-type = <1>;
+ };
+ };
+};

- pinctrl-names = "default";
- pinctrl-0 = <&wlan_sleep_clk_pin>;
+&blsp_i2c11 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c11_pins>;
+ clock-frequency = <355000>;
+ qcom,src-freq = <50000000>;
+
+ lp8566_wled: backlight@2c {
+ compatible = "ti,lp8556";
+ reg = <0x2c>;
+ power-supply = <&vreg_bl_vddio>;
+
+ bl-name = "backlight";
+ dev-ctrl = /bits/ 8 <0x05>;
+ init-brt = /bits/ 8 <0x3f>;
+ rom_a0h {
+ rom-addr = /bits/ 8 <0xa0>;
+ rom-val = /bits/ 8 <0xff>;
+ };
+ rom_a1h {
+ rom-addr = /bits/ 8 <0xa1>;
+ rom-val = /bits/ 8 <0x3f>;
+ };
+ rom_a2h {
+ rom-addr = /bits/ 8 <0xa2>;
+ rom-val = /bits/ 8 <0x20>;
+ };
+ rom_a3h {
+ rom-addr = /bits/ 8 <0xa3>;
+ rom-val = /bits/ 8 <0x5e>;
+ };
+ rom_a4h {
+ rom-addr = /bits/ 8 <0xa4>;
+ rom-val = /bits/ 8 <0x02>;
+ };
+ rom_a5h {
+ rom-addr = /bits/ 8 <0xa5>;
+ rom-val = /bits/ 8 <0x04>;
+ };
+ rom_a6h {
+ rom-addr = /bits/ 8 <0xa6>;
+ rom-val = /bits/ 8 <0x80>;
+ };
+ rom_a7h {
+ rom-addr = /bits/ 8 <0xa7>;
+ rom-val = /bits/ 8 <0xf7>;
+ };
+ rom_a9h {
+ rom-addr = /bits/ 8 <0xa9>;
+ rom-val = /bits/ 8 <0x80>;
+ };
+ rom_aah {
+ rom-addr = /bits/ 8 <0xaa>;
+ rom-val = /bits/ 8 <0x0f>;
+ };
+ rom_aeh {
+ rom-addr = /bits/ 8 <0xae>;
+ rom-val = /bits/ 8 <0x0f>;
};
};
+};
+
+&blsp1_uart2 {
+ status = "okay";

- sdhci@f98a4900 {
- status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_uart2_pin_a>;
+};

- bus-width = <4>;
+&blsp2_uart7 {
+ status = "ok";

- vmmc-supply = <&pm8941_l21>;
- vqmmc-supply = <&pm8941_l13>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp2_uart7_pin_a>;

- cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ max-speed = <3000000>;

pinctrl-names = "default";
- pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
+ pinctrl-0 = <&bt_host_wake_pin>,
+ <&bt_dev_wake_pin>,
+ <&bt_reg_on_pin>;
+
+ host-wakeup-gpios = <&msmgpio 95 GPIO_ACTIVE_HIGH>;
+ device-wakeup-gpios = <&msmgpio 96 GPIO_ACTIVE_HIGH>;
+ shutdown-gpios = <&pm8941_gpios 16 GPIO_ACTIVE_HIGH>;
};
+};

- serial@f991e000 {
- status = "okay";
+&msmgpio {
+ blsp1_uart2_pin_a: blsp1-uart2-pin-active {
+ rx {
+ pins = "gpio5";
+ function = "blsp_uart2";

- pinctrl-names = "default";
- pinctrl-0 = <&blsp1_uart2_pin_a>;
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ tx {
+ pins = "gpio4";
+ function = "blsp_uart2";
+
+ drive-strength = <4>;
+ bias-disable;
+ };
};

- serial@f995d000 {
- status = "ok";
+ blsp2_uart7_pin_a: blsp2-uart7-pin-active {
+ tx {
+ pins = "gpio41";
+ function = "blsp_uart7";

- pinctrl-names = "default";
- pinctrl-0 = <&blsp2_uart7_pin_a>;
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ rx {
+ pins = "gpio42";
+ function = "blsp_uart7";

- bluetooth {
- compatible = "brcm,bcm43438-bt";
- max-speed = <3000000>;
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ cts {
+ pins = "gpio43";
+ function = "blsp_uart7";
+
+ drive-strength = <2>;
+ bias-pull-up;
+ };

- pinctrl-names = "default";
- pinctrl-0 = <&bt_host_wake_pin>,
- <&bt_dev_wake_pin>,
- <&bt_reg_on_pin>;
+ rts {
+ pins = "gpio44";
+ function = "blsp_uart7";

- host-wakeup-gpios = <&msmgpio 95 GPIO_ACTIVE_HIGH>;
- device-wakeup-gpios = <&msmgpio 96 GPIO_ACTIVE_HIGH>;
- shutdown-gpios = <&pm8941_gpios 16 GPIO_ACTIVE_HIGH>;
+ drive-strength = <2>;
+ bias-disable;
};
};

- usb@f9a55000 {
- status = "okay";
+ i2c8_pins: i2c8 {
+ mux {
+ pins = "gpio47", "gpio48";
+ function = "blsp_i2c8";

- phys = <&usb_hs1_phy>;
- phy-select = <&tcsr 0xb000 0>;
- extcon = <&smbb>, <&usb_id>;
- vbus-supply = <&chg_otg>;
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };

- hnp-disable;
- srp-disable;
- adp-disable;
+ i2c11_pins: i2c11 {
+ mux {
+ pins = "gpio83", "gpio84";
+ function = "blsp_i2c11";

- ulpi {
- phy@a {
- status = "okay";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };

- v1p8-supply = <&pm8941_l6>;
- v3p3-supply = <&pm8941_l24>;
+ lcd_backlight_en_pin_a: lcd-backlight-vddio {
+ pins = "gpio69";
+ drive-strength = <10>;
+ output-low;
+ bias-disable;
+ };

- extcon = <&smbb>;
- qcom,init-seq = /bits/ 8 <0x1 0x64>;
- };
+ sdhc1_pin_a: sdhc1-pin-active {
+ clk {
+ pins = "sdc1_clk";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ cmd-data {
+ pins = "sdc1_cmd", "sdc1_data";
+ drive-strength = <10>;
+ bias-pull-up;
};
};

- pinctrl@fd510000 {
- blsp1_uart2_pin_a: blsp1-uart2-pin-active {
- rx {
- pins = "gpio5";
- function = "blsp_uart2";
+ sdhc2_cd_pin_a: sdhc2-cd-pin-active {
+ pins = "gpio62";
+ function = "gpio";

- drive-strength = <2>;
- bias-pull-up;
- };
+ drive-strength = <2>;
+ bias-disable;
+ };

- tx {
- pins = "gpio4";
- function = "blsp_uart2";
+ sdhc2_pin_a: sdhc2-pin-active {
+ clk {
+ pins = "sdc2_clk";
+ drive-strength = <6>;
+ bias-disable;
+ };

- drive-strength = <4>;
- bias-disable;
- };
+ cmd-data {
+ pins = "sdc2_cmd", "sdc2_data";
+ drive-strength = <6>;
+ bias-pull-up;
};
+ };

- blsp2_uart7_pin_a: blsp2-uart7-pin-active {
- tx {
- pins = "gpio41";
- function = "blsp_uart7";
+ sdhc3_pin_a: sdhc3-pin-active {
+ clk {
+ pins = "gpio40";
+ function = "sdc3";

- drive-strength = <2>;
- bias-disable;
- };
+ drive-strength = <10>;
+ bias-disable;
+ };

- rx {
- pins = "gpio42";
- function = "blsp_uart7";
+ cmd {
+ pins = "gpio39";
+ function = "sdc3";

- drive-strength = <2>;
- bias-pull-up;
- };
+ drive-strength = <10>;
+ bias-pull-up;
+ };

- cts {
- pins = "gpio43";
- function = "blsp_uart7";
+ data {
+ pins = "gpio35", "gpio36", "gpio37", "gpio38";
+ function = "sdc3";

- drive-strength = <2>;
- bias-pull-up;
- };
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+ };

- rts {
- pins = "gpio44";
- function = "blsp_uart7";
+ ts_int_pin: synaptics {
+ pin {
+ pins = "gpio86";
+ function = "gpio";

- drive-strength = <2>;
- bias-disable;
- };
+ drive-strength = <2>;
+ bias-disable;
+ input-enable;
};
+ };

- i2c8_pins: i2c8 {
- mux {
- pins = "gpio47", "gpio48";
- function = "blsp_i2c8";
+ bt_host_wake_pin: bt-host-wake {
+ pins = "gpio95";
+ function = "gpio";

- drive-strength = <2>;
- bias-disable;
- };
+ drive-strength = <2>;
+ bias-disable;
+ output-low;
+ };
+
+ bt_dev_wake_pin: bt-dev-wake {
+ pins = "gpio96";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
+
+&otg {
+ status = "okay";
+
+ phys = <&usb_hs1_phy>;
+ phy-select = <&tcsr 0xb000 0>;
+ extcon = <&smbb>, <&usb_id>;
+ vbus-supply = <&chg_otg>;
+
+ hnp-disable;
+ srp-disable;
+ adp-disable;
+
+ ulpi {
+ phy@a {
+ status = "okay";
+
+ v1p8-supply = <&pm8941_l6>;
+ v3p3-supply = <&pm8941_l24>;
+
+ extcon = <&smbb>;
+ qcom,init-seq = /bits/ 8 <0x1 0x64>;
+ };
+ };
+};
+
+&rpm_requests {
+ pm8941-regulators {
+ vdd_l1_l3-supply = <&pm8941_s1>;
+ vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+ vdd_l4_l11-supply = <&pm8941_s1>;
+ vdd_l5_l7-supply = <&pm8941_s2>;
+ vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+ vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
+ vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
+ vdd_l21-supply = <&vreg_boost>;
+
+ s1 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
};

- i2c11_pins: i2c11 {
- mux {
- pins = "gpio83", "gpio84";
- function = "blsp_i2c11";
+ s2 {
+ regulator-min-microvolt = <2150000>;
+ regulator-max-microvolt = <2150000>;
+ regulator-boot-on;
+ };

- drive-strength = <2>;
- bias-disable;
- };
+ s3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-system-load = <154000>;
};

- lcd_backlight_en_pin_a: lcd-backlight-vddio {
- pins = "gpio69";
- drive-strength = <10>;
- output-low;
- bias-disable;
+ s4 {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
};

- sdhc1_pin_a: sdhc1-pin-active {
- clk {
- pins = "sdc1_clk";
- drive-strength = <16>;
- bias-disable;
- };
+ l1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;

- cmd-data {
- pins = "sdc1_cmd", "sdc1_data";
- drive-strength = <10>;
- bias-pull-up;
- };
+ regulator-always-on;
+ regulator-boot-on;
};

- sdhc2_cd_pin_a: sdhc2-cd-pin-active {
- pins = "gpio62";
- function = "gpio";
+ l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };

- drive-strength = <2>;
- bias-disable;
- };
+ l3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };

- sdhc2_pin_a: sdhc2-pin-active {
- clk {
- pins = "sdc2_clk";
- drive-strength = <6>;
- bias-disable;
- };
+ l4 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };

- cmd-data {
- pins = "sdc2_cmd", "sdc2_data";
- drive-strength = <6>;
- bias-pull-up;
- };
+ l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
};

- sdhc3_pin_a: sdhc3-pin-active {
- clk {
- pins = "gpio40";
- function = "sdc3";
+ l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;

- drive-strength = <10>;
- bias-disable;
- };
+ regulator-boot-on;
+ };

- cmd {
- pins = "gpio39";
- function = "sdc3";
+ l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;

- drive-strength = <10>;
- bias-pull-up;
- };
+ regulator-boot-on;
+ };

- data {
- pins = "gpio35", "gpio36", "gpio37", "gpio38";
- function = "sdc3";
+ l8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };

- drive-strength = <10>;
- bias-pull-up;
- };
+ l9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
};

- ts_int_pin: synaptics {
- pin {
- pins = "gpio86";
- function = "gpio";
+ l11 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1350000>;
+ };

- drive-strength = <2>;
- bias-disable;
- input-enable;
- };
+ l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-always-on;
+ regulator-boot-on;
};

- bt_host_wake_pin: bt-host-wake {
- pins = "gpio95";
- function = "gpio";
+ l13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;

- drive-strength = <2>;
- bias-disable;
- output-low;
+ regulator-boot-on;
};

- bt_dev_wake_pin: bt-dev-wake {
- pins = "gpio96";
- function = "gpio";
+ l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };

- drive-strength = <2>;
- bias-disable;
+ l15 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
};
- };

- i2c@f9964000 {
- status = "okay";
+ l16 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };

- clock-frequency = <355000>;
- qcom,src-freq = <50000000>;
+ l17 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };

- pinctrl-names = "default";
- pinctrl-0 = <&i2c8_pins>;
+ l18 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ l19 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };

- synaptics@2c {
- compatible = "syna,rmi4-i2c";
- reg = <0x2c>;
+ l20 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;

- interrupt-parent = <&msmgpio>;
- interrupts = <86 IRQ_TYPE_EDGE_FALLING>;
+ regulator-allow-set-load;
+ regulator-boot-on;
+ regulator-allow-set-load;
+ regulator-system-load = <500000>;
+ };

- #address-cells = <1>;
- #size-cells = <0>;
+ l21 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;

- vdd-supply = <&pm8941_l22>;
- vio-supply = <&pm8941_lvs3>;
+ regulator-boot-on;
+ };

- pinctrl-names = "default";
- pinctrl-0 = <&ts_int_pin>;
+ l22 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };

- syna,startup-delay-ms = <10>;
+ l23 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };

- rmi-f01@1 {
- reg = <0x1>;
- syna,nosleep = <1>;
- };
+ l24 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;

- rmi-f11@11 {
- reg = <0x11>;
- syna,f11-flip-x = <1>;
- syna,sensor-type = <1>;
- };
+ regulator-boot-on;
};
};
+};
+
+&sdhci1 {
+ status = "okay";
+
+ vmmc-supply = <&pm8941_l20>;
+ vqmmc-supply = <&pm8941_s3>;
+
+ bus-width = <8>;
+ non-removable;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc1_pin_a>;
+};
+
+&sdhci2 {
+ status = "okay";
+
+ max-frequency = <100000000>;
+ non-removable;
+ vmmc-supply = <&vreg_wlan>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc3_pin_a>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bcrmf@1 {
+ compatible = "brcm,bcm4339-fmac", "brcm,bcm4329-fmac";
+ reg = <1>;
+
+ brcm,drive-strength = <10>;

- i2c@f9967000 {
- status = "okay";
pinctrl-names = "default";
- pinctrl-0 = <&i2c11_pins>;
- clock-frequency = <355000>;
- qcom,src-freq = <50000000>;
-
- lp8566_wled: backlight@2c {
- compatible = "ti,lp8556";
- reg = <0x2c>;
- power-supply = <&vreg_bl_vddio>;
-
- bl-name = "backlight";
- dev-ctrl = /bits/ 8 <0x05>;
- init-brt = /bits/ 8 <0x3f>;
- rom_a0h {
- rom-addr = /bits/ 8 <0xa0>;
- rom-val = /bits/ 8 <0xff>;
- };
- rom_a1h {
- rom-addr = /bits/ 8 <0xa1>;
- rom-val = /bits/ 8 <0x3f>;
- };
- rom_a2h {
- rom-addr = /bits/ 8 <0xa2>;
- rom-val = /bits/ 8 <0x20>;
- };
- rom_a3h {
- rom-addr = /bits/ 8 <0xa3>;
- rom-val = /bits/ 8 <0x5e>;
- };
- rom_a4h {
- rom-addr = /bits/ 8 <0xa4>;
- rom-val = /bits/ 8 <0x02>;
- };
- rom_a5h {
- rom-addr = /bits/ 8 <0xa5>;
- rom-val = /bits/ 8 <0x04>;
- };
- rom_a6h {
- rom-addr = /bits/ 8 <0xa6>;
- rom-val = /bits/ 8 <0x80>;
- };
- rom_a7h {
- rom-addr = /bits/ 8 <0xa7>;
- rom-val = /bits/ 8 <0xf7>;
- };
- rom_a9h {
- rom-addr = /bits/ 8 <0xa9>;
- rom-val = /bits/ 8 <0x80>;
- };
- rom_aah {
- rom-addr = /bits/ 8 <0xaa>;
- rom-val = /bits/ 8 <0x0f>;
- };
- rom_aeh {
- rom-addr = /bits/ 8 <0xae>;
- rom-val = /bits/ 8 <0x0f>;
- };
- };
+ pinctrl-0 = <&wlan_sleep_clk_pin>;
};
};

+&sdhci3 {
+ status = "okay";
+
+ bus-width = <4>;
+
+ vmmc-supply = <&pm8941_l21>;
+ vqmmc-supply = <&pm8941_l13>;
+
+ cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
+};
+
&spmi_bus {
pm8941@0 {
charger@1000 {
diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts
index a62e5c25b23c..a98aa3e11edf 100644
--- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts
@@ -57,388 +57,382 @@ memory@0 {
reg = <0 0x40000000>, <0x40000000 0x40000000>;
device_type = "memory";
};
+};

- smd {
- rpm {
- rpm_requests {
- pm8841-regulators {
- s1 {
- regulator-min-microvolt = <675000>;
- regulator-max-microvolt = <1050000>;
- };
-
- s2 {
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <1050000>;
- };
-
- s3 {
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <1050000>;
- };
-
- s4 {
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <1050000>;
- };
- };
-
- pm8941-regulators {
- vdd_l1_l3-supply = <&pm8941_s1>;
- vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
- vdd_l4_l11-supply = <&pm8941_s1>;
- vdd_l5_l7-supply = <&pm8941_s2>;
- vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
- vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
- vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
- vdd_l21-supply = <&vreg_boost>;
-
- s1 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- s2 {
- regulator-min-microvolt = <2150000>;
- regulator-max-microvolt = <2150000>;
- regulator-boot-on;
- };
-
- s3 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- s4 {
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- };
-
- l1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- l2 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l3 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l4 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-boot-on;
- };
-
- l7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-boot-on;
- };
-
- l8 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l9 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l11 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1350000>;
- };
-
- l12 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- l13 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-boot-on;
- };
-
- l14 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l15 {
- regulator-min-microvolt = <2050000>;
- regulator-max-microvolt = <2050000>;
- };
-
- l16 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-
- l17 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-
- l18 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- l19 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l20 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-allow-set-load;
- regulator-boot-on;
- regulator-system-load = <200000>;
- };
-
- l21 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-boot-on;
- };
-
- l22 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- l23 {
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- l24 {
- regulator-min-microvolt = <3075000>;
- regulator-max-microvolt = <3075000>;
-
- regulator-boot-on;
- };
- };
- };
+&blsp_i2c2 {
+ status = "okay";
+
+ clock-frequency = <355000>;
+ qcom,src-freq = <50000000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
+
+ synaptics@2c {
+ compatible = "syna,rmi4-i2c";
+ reg = <0x2c>;
+
+ interrupts-extended = <&msmgpio 61 IRQ_TYPE_EDGE_FALLING>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ vdd-supply = <&pm8941_l22>;
+ vio-supply = <&pm8941_lvs3>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&ts_int_pin>;
+
+ syna,startup-delay-ms = <10>;
+
+ rmi4-f01@1 {
+ reg = <0x1>;
+ syna,nosleep-mode = <1>;
+ };
+
+ rmi4-f11@11 {
+ reg = <0x11>;
+ touchscreen-inverted-x;
+ syna,sensor-type = <1>;
};
};
};

-&soc {
- usb@f9a55000 {
- status = "okay";
+&blsp1_uart2 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_uart2_pin_a>;
+};

- phys = <&usb_hs1_phy>;
- phy-select = <&tcsr 0xb000 0>;
- extcon = <&smbb>, <&usb_id>;
- vbus-supply = <&chg_otg>;
+&blsp2_dma {
+ qcom,controlled-remotely;
+};

- hnp-disable;
- srp-disable;
- adp-disable;
+&msmgpio {
+ blsp1_uart2_pin_a: blsp1-uart2-pin-active {
+ rx {
+ pins = "gpio5";
+ function = "blsp_uart2";

- ulpi {
- phy@a {
- status = "okay";
+ drive-strength = <2>;
+ bias-pull-up;
+ };

- v1p8-supply = <&pm8941_l6>;
- v3p3-supply = <&pm8941_l24>;
+ tx {
+ pins = "gpio4";
+ function = "blsp_uart2";

- extcon = <&smbb>;
- qcom,init-seq = /bits/ 8 <0x1 0x64>;
- };
+ drive-strength = <4>;
+ bias-disable;
};
};

- sdhci@f9824900 {
- status = "okay";
+ i2c2_pins: i2c2 {
+ mux {
+ pins = "gpio6", "gpio7";
+ function = "blsp_i2c2";

- vmmc-supply = <&pm8941_l20>;
- vqmmc-supply = <&pm8941_s3>;
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };

- bus-width = <8>;
- non-removable;
+ sdhc1_pin_a: sdhc1-pin-active {
+ clk {
+ pins = "sdc1_clk";
+ drive-strength = <16>;
+ bias-disable;
+ };

- pinctrl-names = "default";
- pinctrl-0 = <&sdhc1_pin_a>;
+ cmd-data {
+ pins = "sdc1_cmd", "sdc1_data";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
};

- sdhci@f98a4900 {
- status = "okay";
+ sdhc2_cd_pin_a: sdhc2-cd-pin-active {
+ pins = "gpio62";
+ function = "gpio";

- bus-width = <4>;
+ drive-strength = <2>;
+ bias-disable;
+ };

- vmmc-supply = <&pm8941_l21>;
- vqmmc-supply = <&pm8941_l13>;
+ sdhc2_pin_a: sdhc2-pin-active {
+ clk {
+ pins = "sdc2_clk";
+ drive-strength = <10>;
+ bias-disable;
+ };

- cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
+ cmd-data {
+ pins = "sdc2_cmd", "sdc2_data";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+ };

- pinctrl-names = "default";
- pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
+ ts_int_pin: touch-int {
+ pin {
+ pins = "gpio61";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-disable;
+ input-enable;
+ };
};
+};

- serial@f991e000 {
- status = "okay";
+&otg {
+ status = "okay";

- pinctrl-names = "default";
- pinctrl-0 = <&blsp1_uart2_pin_a>;
+ phys = <&usb_hs1_phy>;
+ phy-select = <&tcsr 0xb000 0>;
+ extcon = <&smbb>, <&usb_id>;
+ vbus-supply = <&chg_otg>;
+
+ hnp-disable;
+ srp-disable;
+ adp-disable;
+
+ ulpi {
+ phy@a {
+ status = "okay";
+
+ v1p8-supply = <&pm8941_l6>;
+ v3p3-supply = <&pm8941_l24>;
+
+ extcon = <&smbb>;
+ qcom,init-seq = /bits/ 8 <0x1 0x64>;
+ };
};
+};

- i2c@f9924000 {
- status = "okay";
+&rpm_requests {
+ pm8841-regulators {
+ s1 {
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <1050000>;
+ };

- clock-frequency = <355000>;
- qcom,src-freq = <50000000>;
+ s2 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
+ };

- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins>;
+ s3 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
+ };

- synaptics@2c {
- compatible = "syna,rmi4-i2c";
- reg = <0x2c>;
+ s4 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
+ };
+ };

- interrupts-extended = <&msmgpio 61 IRQ_TYPE_EDGE_FALLING>;
+ pm8941-regulators {
+ vdd_l1_l3-supply = <&pm8941_s1>;
+ vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+ vdd_l4_l11-supply = <&pm8941_s1>;
+ vdd_l5_l7-supply = <&pm8941_s2>;
+ vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+ vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
+ vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
+ vdd_l21-supply = <&vreg_boost>;
+
+ s1 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };

- #address-cells = <1>;
- #size-cells = <0>;
+ s2 {
+ regulator-min-microvolt = <2150000>;
+ regulator-max-microvolt = <2150000>;
+ regulator-boot-on;
+ };

- vdd-supply = <&pm8941_l22>;
- vio-supply = <&pm8941_lvs3>;
+ s3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };

- pinctrl-names = "default";
- pinctrl-0 = <&ts_int_pin>;
+ s4 {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };

- syna,startup-delay-ms = <10>;
+ l1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;

- rmi4-f01@1 {
- reg = <0x1>;
- syna,nosleep-mode = <1>;
- };
+ regulator-always-on;
+ regulator-boot-on;
+ };

- rmi4-f11@11 {
- reg = <0x11>;
- touchscreen-inverted-x;
- syna,sensor-type = <1>;
- };
+ l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
};
- };

- pinctrl@fd510000 {
- blsp1_uart2_pin_a: blsp1-uart2-pin-active {
- rx {
- pins = "gpio5";
- function = "blsp_uart2";
+ l3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };

- drive-strength = <2>;
- bias-pull-up;
- };
+ l4 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };

- tx {
- pins = "gpio4";
- function = "blsp_uart2";
+ l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };

- drive-strength = <4>;
- bias-disable;
- };
+ l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-boot-on;
};

- i2c2_pins: i2c2 {
- mux {
- pins = "gpio6", "gpio7";
- function = "blsp_i2c2";
+ l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;

- drive-strength = <2>;
- bias-disable;
- };
+ regulator-boot-on;
};

- sdhc1_pin_a: sdhc1-pin-active {
- clk {
- pins = "sdc1_clk";
- drive-strength = <16>;
- bias-disable;
- };
+ l8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };

- cmd-data {
- pins = "sdc1_cmd", "sdc1_data";
- drive-strength = <10>;
- bias-pull-up;
- };
+ l9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
};

- sdhc2_cd_pin_a: sdhc2-cd-pin-active {
- pins = "gpio62";
- function = "gpio";
+ l11 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1350000>;
+ };

- drive-strength = <2>;
- bias-disable;
- };
+ l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;

- sdhc2_pin_a: sdhc2-pin-active {
- clk {
- pins = "sdc2_clk";
- drive-strength = <10>;
- bias-disable;
- };
+ regulator-always-on;
+ regulator-boot-on;
+ };

- cmd-data {
- pins = "sdc2_cmd", "sdc2_data";
- drive-strength = <6>;
- bias-pull-up;
- };
+ l13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-boot-on;
};

- ts_int_pin: touch-int {
- pin {
- pins = "gpio61";
- function = "gpio";
+ l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };

- drive-strength = <2>;
- bias-disable;
- input-enable;
- };
+ l15 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };
+
+ l16 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
};
- };

- dma-controller@f9944000 {
- qcom,controlled-remotely;
+ l17 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ l18 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ l19 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ l20 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-allow-set-load;
+ regulator-boot-on;
+ regulator-system-load = <200000>;
+ };
+
+ l21 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-boot-on;
+ };
+
+ l22 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ l23 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ l24 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+
+ regulator-boot-on;
+ };
};
};

+&sdhci1 {
+ status = "okay";
+
+ vmmc-supply = <&pm8941_l20>;
+ vqmmc-supply = <&pm8941_s3>;
+
+ bus-width = <8>;
+ non-removable;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc1_pin_a>;
+};
+
+&sdhci3 {
+ status = "okay";
+
+ bus-width = <4>;
+
+ vmmc-supply = <&pm8941_l21>;
+ vqmmc-supply = <&pm8941_l13>;
+
+ cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
+};
+
&spmi_bus {
pm8941@0 {
charger@1000 {
diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
index 412d94736c35..02b73739b6f3 100644
--- a/arch/arm/boot/dts/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
@@ -742,7 +742,7 @@ blsp2_uart10: serial@f9960000 {
status = "disabled";
};

- sdhci@f9824900 {
+ sdhci1: sdhci@f9824900 {
compatible = "qcom,msm8974-sdhci", "qcom,sdhci-msm-v4";
reg = <0xf9824900 0x11c>, <0xf9824000 0x800>;
reg-names = "hc_mem", "core_mem";
@@ -756,7 +756,7 @@ sdhci@f9824900 {
status = "disabled";
};

- sdhci@f9864900 {
+ sdhci2: sdhci@f9864900 {
compatible = "qcom,msm8974-sdhci", "qcom,sdhci-msm-v4";
reg = <0xf9864900 0x11c>, <0xf9864000 0x800>;
reg-names = "hc_mem", "core_mem";
@@ -770,7 +770,7 @@ sdhci@f9864900 {
status = "disabled";
};

- sdhci@f98a4900 {
+ sdhci3: sdhci@f98a4900 {
compatible = "qcom,msm8974-sdhci", "qcom,sdhci-msm-v4";
reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>;
reg-names = "hc_mem", "core_mem";
@@ -835,7 +835,7 @@ rng@f9bff000 {
clock-names = "core";
};

- remoteproc@fc880000 {
+ mss_pil: remoteproc@fc880000 {
compatible = "qcom,msm8974-mss-pil";
reg = <0xfc880000 0x100>, <0xfc820000 0x020>;
reg-names = "qdsp6", "rmb";
@@ -959,7 +959,7 @@ msmgpio: pinctrl@fd510000 {
interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
};

- i2c@f9923000 {
+ blsp_i2c1: i2c@f9923000 {
status = "disabled";
compatible = "qcom,i2c-qup-v2.1.1";
reg = <0xf9923000 0x1000>;
@@ -970,7 +970,7 @@ i2c@f9923000 {
#size-cells = <0>;
};

- i2c@f9924000 {
+ blsp_i2c2: i2c@f9924000 {
status = "disabled";
compatible = "qcom,i2c-qup-v2.1.1";
reg = <0xf9924000 0x1000>;
@@ -1594,7 +1594,7 @@ dsi_phy0: dsi-phy@fd922a00 {
};
};

- imem@fe805000 {
+ imem: imem@fe805000 {
status = "disabled";
compatible = "syscon", "simple-mfd";
reg = <0xfe805000 0x1000>;
@@ -1614,7 +1614,7 @@ rpm {
qcom,ipc = <&apcs 8 0>;
qcom,smd-edge = <15>;

- rpm_requests {
+ rpm_requests: rpm_requests {
compatible = "qcom,rpm-msm8974";
qcom,smd-channels = "rpm_requests";

--
2.32.0
\
 
 \ /
  Last update: 2022-04-01 22:12    [W:0.367 / U:0.232 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site