lkml.org 
[lkml]   [2022]   [Mar]   [31]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [RFCv2 PATCH 09/12] KVM: SVM: Refresh AVIC settings when changing APIC mode
From
Hi Maxim,

On 3/24/22 10:35 PM, Maxim Levitsky wrote:
> On Tue, 2022-03-08 at 10:39 -0600, Suravee Suthikulpanit wrote:
>> When APIC mode is updated (e.g. from xAPIC to x2APIC),
>> KVM needs to update AVIC settings accordingly, whic is
>> handled by svm_refresh_apicv_exec_ctrl().
>>
>> Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
>> ---
>> arch/x86/kvm/svm/avic.c | 19 ++++++++++++++++++-
>> 1 file changed, 18 insertions(+), 1 deletion(-)
>>
>> diff --git a/arch/x86/kvm/svm/avic.c b/arch/x86/kvm/svm/avic.c
>> index 7e5a39a8e698..53559b8dfa52 100644
>> --- a/arch/x86/kvm/svm/avic.c
>> +++ b/arch/x86/kvm/svm/avic.c
>> @@ -625,7 +625,24 @@ void avic_post_state_restore(struct kvm_vcpu *vcpu)
>>
>> void svm_set_virtual_apic_mode(struct kvm_vcpu *vcpu)
>> {
>> - return;
>> + struct vcpu_svm *svm = to_svm(vcpu);
>> +
>> + if (!lapic_in_kernel(vcpu) || (avic_mode == AVIC_MODE_NONE))
>> + return;
>> +
>> + if (kvm_get_apic_mode(vcpu) == LAPIC_MODE_INVALID)
>> + WARN_ONCE(true, "Invalid local APIC state");
>> +
>> + svm->vmcb->control.avic_vapic_bar = svm->vcpu.arch.apic_base &
>> + VMCB_AVIC_APIC_BAR_MASK;
>
> No need for that - APIC base relocation doesn't work when AVIC is enabled,
> since the page which contains it has to be marked R/W in NPT, which we
> only do for the default APIC base.
>
> I recently removed the code from AVIC which still tried to set the
> 'avic_vapic_bar' like this.

Got it. I'll remove this part.

>
>> + kvm_vcpu_update_apicv(&svm->vcpu);
>> +
>> + /*
>> + * The VM could be running w/ AVIC activated switching from APIC
>> + * to x2APIC mode. We need to all refresh to make sure that all
>> + * x2AVIC configuration are being done.
>
> Why? When AVIC is un-inhibited later then the svm_refresh_apicv_exec_ctrl will be called
> again and switch to x2avic mode I think.

Current version does not disable AVIC when APIC is disabled, which happens during
APIC mode switching (i.e. xAPIC -> disabled -> x2APIC). This needs to be fixed.
Then we can remove the force refresh.

> When AVIC is inhibited, then regardless of x2apic mode, VMCB must not have
> any avic bits set, and all x2apic msrs should be read/write intercepted.,
> thus I don't think that svm_refresh_apicv_exec_ctrl should be force called.

The refresh is normally called only when there is APICV update request (e.g.
kvm_request_apicv_update(APICV_INHIBIT_REASON_IRQWIN)), which could happen or not.


However, I have reworked this part. The svm_refresh_apicv_exec_ctrl()
force is no longer needed.

Regards,
Suravee

\
 
 \ /
  Last update: 2022-03-31 06:17    [W:0.130 / U:0.120 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site