lkml.org 
[lkml]   [2022]   [Mar]   [31]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH] dt-bindings: display: msm: dsi: remove address/size cells
On Thu, 31 Mar 2022 at 09:05, Vinod Koul <vkoul@kernel.org> wrote:
>
> On 29-03-22, 10:52, Rob Herring wrote:
> > On Tue, Mar 29, 2022 at 12:01:52PM +0530, Vinod Koul wrote:
> > > On 28-03-22, 13:21, Rob Herring wrote:
> > > > On Mon, Mar 28, 2022 at 12:18 PM Krzysztof Kozlowski
> > > > <krzysztof.kozlowski@linaro.org> wrote:
> > > > >
> > > > > On 28/03/2022 19:16, Vinod Koul wrote:
> > > > > > On 28-03-22, 19:43, Dmitry Baryshkov wrote:
> > > > > >> On Mon, 28 Mar 2022 at 18:30, Krzysztof Kozlowski
> > > > > >> <krzysztof.kozlowski@linaro.org> wrote:
> > > > > >>>
> > > > > >>> The DSI node is not a bus and the children do not have unit addresses.
> > > > > >>>
> > > > > >>> Reported-by: Vinod Koul <vkoul@kernel.org>
> > > > > >>> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> > > > > >>
> > > > > >> NAK.
> > > > > >> DSI panels are children of the DSI device tree node with the reg = <0>; address.
> > > > > >> This is the convention used by other platforms too (see e.g.
> > > > > >> arch/arm64/boot/dts/freescale/imx8mq-evk.dts).
> > > > > >
> > > > > > So we should add reg = 0, i will update my dtsi fix
> > > > > >
> > > > >
> > > > > To "ports" node? No. The reg=0 is for children of the bus, so the
> > > > > panels. How to combine both without warnings - ports and panel@0 - I
> > > > > don't know yet...
> > > >
> > > > I don't think that should case a warning. Or at least it's one we turn off.
> > >
> > > Well in this case I think we might need a fix:
> > > Here is the example quoted in the binding. We have ports{} and then the
> > > two port@0 and port@1 underneath.
> >
> > It's the #address-cells/#size-cells under 'ports' that applies to 'port'
> > nodes. As 'ports' has no address (reg) itself, it doesn't need
> > #address-cells/#size-cells in its parent node.
> >
> > >
> > > So it should be okay to drop #address-cells/#size-cells from dsi node
> > > but keep in ports node...
> >
> > Yes.
> >
> > > Thoughts...?
> >
> > But I thought a panel@0 node was being added? If so then you need to add
> > them back.
>
> I guess we should make this optional, keep it when adding panel@0 node
> and skip for rest where not applicable..? Dmitry is that fine with you?

This sounds like a workaround. When a panel node is added together
with the '#address-cells' / '#size-cells' properties, we will get
warnings for the 'ports' node.
I'd prefer to leave things to pinpoint that the problem is generic
rather than being specific to several device trees with the DSI panel
nodes.
How do other platforms solve the issue?

In fact we can try shifting to the following dts schema:

dsi@ae940000 {
compatible = "qcom,mdss-dsi-ctrl";

ports {
#adress-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
dsi0_in: endpoint {};
};
port@1 {
reg = <1>;
dsi0_out: endpoint {
remote-endpoint = <&panel_in>;
};
};

/* dsi-bus is a generic part */
dsi-bus {
#adress-cells = <1>;
#size-cells = <0>;
/* panel@0 goes to the board file */
panel@0 {
compatible = "vendor,some-panel";
ports {
#adress-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
panel_in: endpoint {
remote-endpoint = <&dsi0_out>;
};
};
};
};
};

WDYT?

--
With best wishes
Dmitry

\
 
 \ /
  Last update: 2022-03-31 11:36    [W:0.074 / U:0.076 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site