lkml.org 
[lkml]   [2022]   [Mar]   [31]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v11 2/5] usb: dwc3: core: Host wake up support from system suspend
Hi Matthias,

On Wed, Mar 30, 2022 at 09:46:36AM -0700, Matthias Kaehlcke wrote:
> On Wed, Mar 30, 2022 at 09:33:18AM +0530, Pavan Kondeti wrote:
> > Hi Sandeep/Matthias,
> >
> > On Thu, Mar 24, 2022 at 10:24:55AM +0530, Sandeep Maheswaram (Temp) wrote:
> > >
> > > On 3/23/2022 11:37 PM, Matthias Kaehlcke wrote:
> > > >On Tue, Mar 22, 2022 at 12:37:53PM +0530, Sandeep Maheswaram wrote:
> > > >>During suspend read the status of all port and make sure the PHYs
> > > >>are in the correct mode based on current speed.
> > > >>Phy interrupt masks are set based on this mode. Keep track of the mode
> > > >>of the HS PHY to be able to configure wakeup properly.
> > > >>
> > > >>Also check during suspend if any wakeup capable devices are
> > > >>connected to the controller (directly or through hubs), if there
> > > >>are none set a flag to indicate that the PHY is powered
> > > >>down during suspend.
> > > >>
> > > >>Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
> > > >>---
> > > >> drivers/usb/dwc3/core.c | 54 ++++++++++++++++++++++++++++++++++++++++---------
> > > >> 1 file changed, 45 insertions(+), 9 deletions(-)
> > > >>
> > > >>diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
> > > >>index 1170b80..232a734 100644
> > > >>--- a/drivers/usb/dwc3/core.c
> > > >>+++ b/drivers/usb/dwc3/core.c
> > > >>@@ -32,12 +32,14 @@
> > > >> #include <linux/usb/gadget.h>
> > > >> #include <linux/usb/of.h>
> > > >> #include <linux/usb/otg.h>
> > > >>+#include <linux/usb/hcd.h>
> > > >> #include "core.h"
> > > >> #include "gadget.h"
> > > >> #include "io.h"
> > > >> #include "debug.h"
> > > >>+#include "../host/xhci.h"
> > > >> #define DWC3_DEFAULT_AUTOSUSPEND_DELAY 5000 /* ms */
> > > >>@@ -1861,10 +1863,36 @@ static int dwc3_core_init_for_resume(struct dwc3 *dwc)
> > > >> return ret;
> > > >> }
> > > >>+static void dwc3_set_phy_speed_mode(struct dwc3 *dwc)
> > > >>+{
> > > >>+
> > > >>+ int i, num_ports;
> > > >>+ u32 reg;
> > > >>+ struct usb_hcd *hcd = platform_get_drvdata(dwc->xhci);
> > > >>+ struct xhci_hcd *xhci_hcd = hcd_to_xhci(hcd);
> > > >>+
> > > >>+ dwc->hs_phy_mode = 0;
> > > >>+
> > > >>+ reg = readl(&xhci_hcd->cap_regs->hcs_params1);
> > > >>+
> > > >>+ num_ports = HCS_MAX_PORTS(reg);
> > > >>+ for (i = 0; i < num_ports; i++) {
> > > >>+ reg = readl(&xhci_hcd->op_regs->port_status_base + i * 0x04);
> > > >s/0x04/NUM_PORT_REGS/
> > > Okay. Will update in next version.
> > > >
> > > >>+ if (reg & PORT_PE) {
> > > >>+ if (DEV_HIGHSPEED(reg) || DEV_FULLSPEED(reg))
> > > >>+ dwc->hs_phy_mode |= PHY_MODE_USB_HOST_HS;
> > > >>+ else if (DEV_LOWSPEED(reg))
> > > >>+ dwc->hs_phy_mode |= PHY_MODE_USB_HOST_LS;
> > > >>+ }
> > > >>+ }
> > > >>+ phy_set_mode(dwc->usb2_generic_phy, dwc->hs_phy_mode);
> > > >>+}
> > > >>+
> > > >> static int dwc3_suspend_common(struct dwc3 *dwc, pm_message_t msg)
> > > >> {
> > > >> unsigned long flags;
> > > >> u32 reg;
> > > >>+ struct usb_hcd *hcd = platform_get_drvdata(dwc->xhci);
> > > >> switch (dwc->current_dr_role) {
> > > >> case DWC3_GCTL_PRTCAP_DEVICE:
> > > >>@@ -1877,10 +1905,7 @@ static int dwc3_suspend_common(struct dwc3 *dwc, pm_message_t msg)
> > > >> dwc3_core_exit(dwc);
> > > >> break;
> > > >> case DWC3_GCTL_PRTCAP_HOST:
> > > >>- if (!PMSG_IS_AUTO(msg)) {
> > > >>- dwc3_core_exit(dwc);
> > > >>- break;
> > > >>- }
> > > >>+ dwc3_set_phy_speed_mode(dwc);
> > > >> /* Let controller to suspend HSPHY before PHY driver suspends */
> > > >> if (dwc->dis_u2_susphy_quirk ||
> > > >>@@ -1896,6 +1921,16 @@ static int dwc3_suspend_common(struct dwc3 *dwc, pm_message_t msg)
> > > >> phy_pm_runtime_put_sync(dwc->usb2_generic_phy);
> > > >> phy_pm_runtime_put_sync(dwc->usb3_generic_phy);
> > > >>+
> > > >>+ if (!PMSG_IS_AUTO(msg)) {
> > > >>+ if (device_may_wakeup(&dwc->xhci->dev) &&
> > > >Does the xHCI actually provide the correct information? I think Brian brought
> > > >up earlier that xhci-plat always marks the xHCI as wakeup capable, regardless
> > > >of whether the specific implementation actually supports wakeup. So a dwc3
> > > >without wakeup support would keep the PHY and the dwc3 active during suspend
> > > >if wakeup capable devices are connected (unless the admin disabled wakeup),
> > > >even though wakeup it doesn't support wakeup.
> > > >
> > > >Using the wakeup capability/policy of the xHCI to make decisions in the dwc3
> > > >driver might still be the best we can do with the weird driver split over 3
> > > >drivers for dwc3. Maybe the dwc3 could pass the actual capability to wake up
> > > >to the xHCI through a property_entry? Then again, it's actually the 'glue'
> > > >driver (dwc3-qcom) who knows about the actual wakeup capability, and not the
> > > >dwc3 core/host ...
> > > Will check if we can do something regarding this.
> >
> > Can we introduce a device tree param to xhci-plat to specify if the underlying
> > device is wakeup capable or not. Based on this xhci-plat can call
> > device_set_wakeup_capable() with correct argument.
>
> This also came to my mind, the existing 'wakeup-source' property could be an
> option, I share your concern about breaking existing use cases though ...
>
> > One immediate problem is that current code unconditionally calls
> > device_set_wakeup_capable(&pdev->dev, true). So we may break existing use
> > cases also.
>
> > Given that xHC assumes that the undelying device is wakeup capable but dwc3
> > tearing the stack during PM suspend does not make any sense. can we atleast
> > create a device tree param for dwc3 not to do this?
>
> I'm not sure I fully understand what you have in mind. Are you thinking about
> a parameter/property to indicate whether wakeup should be enabled for the dwc3?
> 'wakeup_source' could serve that purpose, it is also used by xhci-mtk.c and
> mtu3_host.c.

Yes, I was suggesting we can have a device tree param for dwc3 node to decide
instead of relying on device_may_wakeup() checks in this patch.

Thanks for pointing out wakeup-source property. That sounds perfect here to
me.

Thanks,
Pavan

\
 
 \ /
  Last update: 2022-03-31 06:11    [W:0.085 / U:0.132 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site