lkml.org 
[lkml]   [2022]   [Mar]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe:
On Wed, Mar 30, 2022 at 1:09 PM Michael S. Tsirkin <mst@redhat.com> wrote:
>
> On Wed, Mar 30, 2022 at 10:38:06AM +0800, Jason Wang wrote:
> > On Wed, Mar 30, 2022 at 6:04 AM Michael S. Tsirkin <mst@redhat.com> wrote:
> > >
> > > On Tue, Mar 29, 2022 at 08:13:57PM +0200, Thomas Gleixner wrote:
> > > > On Tue, Mar 29 2022 at 10:37, Michael S. Tsirkin wrote:
> > > > > On Tue, Mar 29, 2022 at 10:35:21AM +0200, Thomas Gleixner wrote:
> > > > > We are trying to fix the driver since at the moment it does not
> > > > > have the dev->ok flag at all.
> > > > >
> > > > > And I suspect virtio is not alone in that.
> > > > > So it would have been nice if there was a standard flag
> > > > > replacing the driver-specific dev->ok above, and ideally
> > > > > would also handle the case of an interrupt triggering
> > > > > too early by deferring the interrupt until the flag is set.
> > > > >
> > > > > And in fact, it does kind of exist: IRQF_NO_AUTOEN, and you would call
> > > > > enable_irq instead of dev->ok = true, except
> > > > > - it doesn't work with affinity managed IRQs
> > > > > - it does not work with shared IRQs
> > > > >
> > > > > So using dev->ok as you propose above seems better at this point.
> > > >
> > > > Unless there is a big enough amount of drivers which could make use of a
> > > > generic mechanism for that.
> > > >
> > > > >> If any driver does this in the wrong order, then the driver is
> > > > >> broken.
> > > > >
> > > > > I agree, however:
> > > > > $ git grep synchronize_irq `git grep -l request_irq drivers/net/`|wc -l
> > > > > 113
> > > > > $ git grep -l request_irq drivers/net/|wc -l
> > > > > 397
> > > > >
> > > > > I suspect there are more drivers which in theory need the
> > > > > synchronize_irq dance but in practice do not execute it.
> > > >
> > > > That really depends on when the driver requests the interrupt, when
> > > > it actually enables the interrupt in the device itself
> > >
> > > This last point does not matter since we are talking about protecting
> > > against buggy/malicious devices. They can inject the interrupt anyway
> > > even if driver did not configure it.
> > >
> > > > and how the
> > > > interrupt service routine works.
> > > >
> > > > So just doing that grep dance does not tell much. You really have to do
> > > > a case by case analysis.
> > > >
> > > > Thanks,
> > > >
> > > > tglx
> > >
> > >
> > > I agree. In fact, at least for network the standard approach is to
> > > request interrupts in the open call, virtio net is unusual
> > > in doing it in probe. We should consider changing that.
> > > Jason?
> >
> > This probably works only for virtio-net and it looks like not trivial
> > since we don't have a specific core API to request interrupts.
> >
> > Thanks
>
> We'll need a new API, for sure. E.g. find vqs with no
> callback on probe, and then virtio_request_vq_callbacks separately.
>
> The existing API that specifies callbacks during find vqs
> can be used by other drivers.

Ok, I will do it.

Thanks

>
> > >
> > > --
> > > MST
> > >
>

\
 
 \ /
  Last update: 2022-03-30 07:55    [W:0.127 / U:0.252 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site