lkml.org 
[lkml]   [2022]   [Mar]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 4/4] spi: dt-bindings: qcom,spi-qup: convert to dtschema
On Tue, Mar 29, 2022 at 01:29:02PM +0200, Krzysztof Kozlowski wrote:
> Convert the Qualcomm Universal Peripheral (QUP) Serial Peripheral
> Interface (SPI) bindings to DT Schema.
>
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> ---
> .../devicetree/bindings/spi/qcom,spi-qup.txt | 103 ------------------
> .../devicetree/bindings/spi/qcom,spi-qup.yaml | 82 ++++++++++++++
> 2 files changed, 82 insertions(+), 103 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/spi/qcom,spi-qup.txt
> create mode 100644 Documentation/devicetree/bindings/spi/qcom,spi-qup.yaml
>
> diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt b/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt
> deleted file mode 100644
> index 5c090771c016..000000000000
> --- a/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt
> +++ /dev/null
> @@ -1,103 +0,0 @@
> -Qualcomm Universal Peripheral (QUP) Serial Peripheral Interface (SPI)
> -
> -The QUP core is an AHB slave that provides a common data path (an output FIFO
> -and an input FIFO) for serial peripheral interface (SPI) mini-core.
> -
> -SPI in master mode supports up to 50MHz, up to four chip selects, programmable
> -data path from 4 bits to 32 bits and numerous protocol variants.
> -
> -Required properties:
> -- compatible: Should contain:
> - "qcom,spi-qup-v1.1.1" for 8660, 8960 and 8064.
> - "qcom,spi-qup-v2.1.1" for 8974 and later
> - "qcom,spi-qup-v2.2.1" for 8974 v2 and later.
> -
> -- reg: Should contain base register location and length
> -- interrupts: Interrupt number used by this controller
> -
> -- clocks: Should contain the core clock and the AHB clock.
> -- clock-names: Should be "core" for the core clock and "iface" for the
> - AHB clock.
> -
> -- #address-cells: Number of cells required to define a chip select
> - address on the SPI bus. Should be set to 1.
> -- #size-cells: Should be zero.
> -
> -Optional properties:
> -- spi-max-frequency: Specifies maximum SPI clock frequency,
> - Units - Hz. Definition as per
> - Documentation/devicetree/bindings/spi/spi-bus.txt
> -- num-cs: total number of chipselects
> -- cs-gpios: should specify GPIOs used for chipselects.
> - The gpios will be referred to as reg = <index> in the SPI child
> - nodes. If unspecified, a single SPI device without a chip
> - select can be used.
> -
> -- dmas: Two DMA channel specifiers following the convention outlined
> - in bindings/dma/dma.txt
> -- dma-names: Names for the dma channels, if present. There must be at
> - least one channel named "tx" for transmit and named "rx" for
> - receive.
> -
> -SPI slave nodes must be children of the SPI master node and can contain
> -properties described in Documentation/devicetree/bindings/spi/spi-bus.txt
> -
> -Example:
> -
> - spi_8: spi@f9964000 { /* BLSP2 QUP2 */
> -
> - compatible = "qcom,spi-qup-v2";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - reg = <0xf9964000 0x1000>;
> - interrupts = <0 102 0>;
> - spi-max-frequency = <19200000>;
> -
> - clocks = <&gcc GCC_BLSP2_QUP2_SPI_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
> - clock-names = "core", "iface";
> -
> - dmas = <&blsp1_bam 13>, <&blsp1_bam 12>;
> - dma-names = "rx", "tx";
> -
> - pinctrl-names = "default";
> - pinctrl-0 = <&spi8_default>;
> -
> - device@0 {
> - compatible = "arm,pl022-dummy";
> - #address-cells = <1>;
> - #size-cells = <1>;
> - reg = <0>; /* Chip select 0 */
> - spi-max-frequency = <19200000>;
> - spi-cpol;
> - };
> -
> - device@1 {
> - compatible = "arm,pl022-dummy";
> - #address-cells = <1>;
> - #size-cells = <1>;
> - reg = <1>; /* Chip select 1 */
> - spi-max-frequency = <9600000>;
> - spi-cpha;
> - };
> -
> - device@2 {
> - compatible = "arm,pl022-dummy";
> - #address-cells = <1>;
> - #size-cells = <1>;
> - reg = <2>; /* Chip select 2 */
> - spi-max-frequency = <19200000>;
> - spi-cpol;
> - spi-cpha;
> - };
> -
> - device@3 {
> - compatible = "arm,pl022-dummy";
> - #address-cells = <1>;
> - #size-cells = <1>;
> - reg = <3>; /* Chip select 3 */
> - spi-max-frequency = <19200000>;
> - spi-cpol;
> - spi-cpha;
> - spi-cs-high;
> - };
> - };
> diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-qup.yaml b/Documentation/devicetree/bindings/spi/qcom,spi-qup.yaml
> new file mode 100644
> index 000000000000..aa5756f7ba85
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/spi/qcom,spi-qup.yaml
> @@ -0,0 +1,82 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/spi/qcom,spi-qup.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Qualcomm Universal Peripheral (QUP) Serial Peripheral Interface (SPI)
> +
> +maintainers:
> + - Andy Gross <agross@kernel.org>
> + - Bjorn Andersson <bjorn.andersson@linaro.org>
> + - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> +
> +description:
> + The QUP core is an AHB slave that provides a common data path (an output FIFO
> + and an input FIFO) for serial peripheral interface (SPI) mini-core.
> +
> + SPI in master mode supports up to 50MHz, up to four chip selects,
> + programmable data path from 4 bits to 32 bits and numerous protocol variants.
> +
> +allOf:
> + - $ref: /spi/spi-controller.yaml#

Same thing for reference here as we discussed on other thread.

> +
> +properties:
> + compatible:
> + enum:
> + - qcom,spi-qup-v1.1.1 # for 8660, 8960 and 8064
> + - qcom,spi-qup-v2.1.1 # for 8974 and later
> + - qcom,spi-qup-v2.2.1 # for 8974 v2 and later
> +
> + clocks:
> + maxItems: 2
> +
> + clock-names:
> + items:
> + - const: core
> + - const: iface
> +
> + dmas:
> + maxItems: 2
> +
> + dma-names:
> + items:
> + - const: tx
> + - const: rx

Just wanted to confirm one thing, did you try with rx-tx?
As once I noticed for some other spec, that warnings were reduced when
order was reversed as most of the DTs follow rx-tx order.

We can keep order which disturb less DTs.

> +
> + interrupts:
> + maxItems: 1
> +
> + reg:
> + maxItems: 1
> +
> +required:
> + - compatible
> + - clocks
> + - clock-names
> + - interrupts
> + - reg
> +
> +unevaluatedProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/clock/qcom,gcc-msm8996.h>
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> +
> + spi@7575000 {
> + compatible = "qcom,spi-qup-v2.2.1";
> + reg = <0x07575000 0x600>;
> + interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>,
> + <&gcc GCC_BLSP1_AHB_CLK>;
> + clock-names = "core",
> + "iface";

clock-names can be written in one line.

> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&blsp1_spi1_default>;
> + pinctrl-1 = <&blsp1_spi1_sleep>;
> + dmas = <&blsp1_dma 12>, <&blsp1_dma 13>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> --
> 2.32.0
>

\
 
 \ /
  Last update: 2022-03-30 13:44    [W:0.463 / U:0.032 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site