lkml.org 
[lkml]   [2022]   [Mar]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v2] brcmfmac: Avoid keeping power to SDIO card unless WOWL is used
From
On 3/23/22 09:39, Ulf Hansson wrote:
> Keeping the power to the SDIO card during system wide suspend, consumes
> energy. Especially on battery driven embedded systems, this can be a
> problem. Therefore, let's change the behaviour into allowing the SDIO card
> to be powered off, unless WOWL is supported and enabled.
>
> Note that, the downside from this change, is that during system resume the
> SDIO card needs to be re-initialized and the FW must be re-programmed. Even
> if this may take some time to complete, it should we worth it, rather than
> draining the battery.
>
> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
> ---
>
> Changes in v2:
> - As pointed out by Yann, the changes for the resume path was missing,
> so I have added that too.
>
> Again, please note that, I have only compile-tested this patch, so I am relying
> on help from Yann and others to run tests on real HW.
>
> Kind regards
> Ulf Hansson
>
> ---
> .../broadcom/brcm80211/brcmfmac/bcmsdh.c | 39 +++++++++++--------
> 1 file changed, 22 insertions(+), 17 deletions(-)
>
> diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c
> index ac02244a6fdf..9c598ea97499 100644
> --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c
> +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c
> @@ -1119,9 +1119,21 @@ void brcmf_sdio_wowl_config(struct device *dev, bool enabled)
> {
> struct brcmf_bus *bus_if = dev_get_drvdata(dev);
> struct brcmf_sdio_dev *sdiodev = bus_if->bus_priv.sdio;
> + mmc_pm_flag_t pm_caps = sdio_get_host_pm_caps(sdiodev->func1);
>
> - brcmf_dbg(SDIO, "Configuring WOWL, enabled=%d\n", enabled);
> - sdiodev->wowl_enabled = enabled;
> + /* Power must be preserved to be able to support WOWL. */
> + if (!(pm_caps & MMC_PM_KEEP_POWER))
> + goto notsup;
> +
> + if (sdiodev->settings->bus.sdio.oob_irq_supported ||
> + pm_caps & MMC_PM_WAKE_SDIO_IRQ) {
> + sdiodev->wowl_enabled = enabled;
> + brcmf_dbg(SDIO, "Configuring WOWL, enabled=%d\n", enabled);
> + return;
> + }
> +
> +notsup:
> + brcmf_dbg(SDIO, "WOWL not supported\n");
> }
>
> #ifdef CONFIG_PM_SLEEP
> @@ -1130,7 +1142,7 @@ static int brcmf_ops_sdio_suspend(struct device *dev)
> struct sdio_func *func;
> struct brcmf_bus *bus_if;
> struct brcmf_sdio_dev *sdiodev;
> - mmc_pm_flag_t pm_caps, sdio_flags;
> + mmc_pm_flag_t sdio_flags;
> int ret = 0;
>
> func = container_of(dev, struct sdio_func, dev);
> @@ -1142,20 +1154,15 @@ static int brcmf_ops_sdio_suspend(struct device *dev)
> bus_if = dev_get_drvdata(dev);
> sdiodev = bus_if->bus_priv.sdio;
>
> - pm_caps = sdio_get_host_pm_caps(func);
> -
> - if (pm_caps & MMC_PM_KEEP_POWER) {
> - /* preserve card power during suspend */
> + if (sdiodev->wowl_enabled) {
> brcmf_sdiod_freezer_on(sdiodev);
> brcmf_sdio_wd_timer(sdiodev->bus, 0);
>
> sdio_flags = MMC_PM_KEEP_POWER;
> - if (sdiodev->wowl_enabled) {
> - if (sdiodev->settings->bus.sdio.oob_irq_supported)
> - enable_irq_wake(sdiodev->settings->bus.sdio.oob_irq_nr);
> - else
> - sdio_flags |= MMC_PM_WAKE_SDIO_IRQ;
> - }
> + if (sdiodev->settings->bus.sdio.oob_irq_supported)
> + enable_irq_wake(sdiodev->settings->bus.sdio.oob_irq_nr);
> + else
> + sdio_flags |= MMC_PM_WAKE_SDIO_IRQ;
>
> if (sdio_set_host_pm_flags(sdiodev->func1, sdio_flags))
> brcmf_err("Failed to set pm_flags %x\n", sdio_flags);
> @@ -1176,21 +1183,19 @@ static int brcmf_ops_sdio_resume(struct device *dev)
> struct brcmf_bus *bus_if = dev_get_drvdata(dev);
> struct brcmf_sdio_dev *sdiodev = bus_if->bus_priv.sdio;
> struct sdio_func *func = container_of(dev, struct sdio_func, dev);
> - mmc_pm_flag_t pm_caps = sdio_get_host_pm_caps(func);
> int ret = 0;
>
> brcmf_dbg(SDIO, "Enter: F%d\n", func->num);
> if (func->num != 2)
> return 0;
>
> - if (!(pm_caps & MMC_PM_KEEP_POWER)) {
> + if (!sdiodev->wowl_enabled) {
> /* bus was powered off and device removed, probe again */
> ret = brcmf_sdiod_probe(sdiodev);
> if (ret)
> brcmf_err("Failed to probe device on resume\n");
> } else {
> - if (sdiodev->wowl_enabled &&
> - sdiodev->settings->bus.sdio.oob_irq_supported)
> + if (sdiodev->settings->bus.sdio.oob_irq_supported)
> disable_irq_wake(sdiodev->settings->bus.sdio.oob_irq_nr);
>
> brcmf_sdiod_freezer_off(sdiodev);

Hi Ulf,

Thanks for the patch, it is OK, and tested by Christophe (R.).
So you can add:
Tested-by: Christophe Roullier <christophe.roullier@foss.st.com>
Acked-by: Yann Gautier <yann.gautier@foss.st.com>


Best regards,
Yann

\
 
 \ /
  Last update: 2022-03-23 14:23    [W:0.116 / U:0.096 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site