lkml.org 
[lkml]   [2022]   [Mar]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v8 1/3] dt-bindings: mmc: mtk-sd: extend interrupts and pinctrls properties
From
Date
On Mon, 2022-03-21 at 18:29 -0500, Rob Herring wrote:
> On Mon, Mar 21, 2022 at 07:51:32PM +0800, Axe Yang wrote:
> > Extend interrupts and pinctrls for SDIO wakeup interrupt feature.
> > This feature allow SDIO devices alarm asynchronous interrupt to
> > host
> > even when host stop providing clock to SDIO card. An extra wakeup
> > interrupt and pinctrl states for SDIO DAT1 pin state switching are
> > required in this scenario.
> >
> > Signed-off-by: Axe Yang <axe.yang@mediatek.com>
> > ---
> > .../devicetree/bindings/mmc/mtk-sd.yaml | 23
> > ++++++++++++++++++-
> > 1 file changed, 22 insertions(+), 1 deletion(-)
> >
> > diff --git a/Documentation/devicetree/bindings/mmc/mtk-sd.yaml
> > b/Documentation/devicetree/bindings/mmc/mtk-sd.yaml
> > index 297ada03e3de..f57774535a1d 100644
> > --- a/Documentation/devicetree/bindings/mmc/mtk-sd.yaml
> > +++ b/Documentation/devicetree/bindings/mmc/mtk-sd.yaml
> > @@ -69,12 +69,23 @@ properties:
> > - const: ahb_cg
> >
> > interrupts:
> > - maxItems: 1
> > + description:
> > + Should at least contain MSDC GIC interrupt. To support SDIO
> > in-band wakeup, an extended
> > + interrupt is required and be configured as wakeup source
> > irq.
> > + minItems: 1
> > + maxItems: 2
> >
> > pinctrl-names:
> > + description:
> > + Should at least contain default and state_uhs. To support
> > SDIO in-band wakeup, dat1 pin
> > + will be switched between GPIO mode and SDIO DAT1 mode,
> > state_eint and state_dat1 are
> > + mandatory in this scenarios.
> > + minItems: 2
> > items:
> > - const: default
> > - const: state_uhs
> > + - const: state_eint
> > + - const: state_dat1
> >
> > pinctrl-0:
> > description:
> > @@ -86,6 +97,16 @@ properties:
> > should contain uhs mode pin ctrl.
> > maxItems: 1
> >
> > + pinctrl-2:
> > + description:
> > + should switch dat1 pin to GPIO mode.
> > + maxItems: 1
> > +
> > + pinctrl-3:
> > + description:
> > + should switch SDIO dat1 pin from GPIO mode back to SDIO
> > mode.
>
> How is this different than pinctrl-0?

pinctrl-0 contains default settings for all IO pins(CLK/CMD/DAT).
pinctrl-1 contains settings for all IO pins(CLK/CMD/DAT) in UHS mode.
pinctrl-3 is lightweight pinctrl-1, only keep SDIO DAT1 pin function
switch part.

...

Regards,
Axe

\
 
 \ /
  Last update: 2022-03-22 02:36    [W:0.055 / U:0.200 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site