lkml.org 
[lkml]   [2022]   [Mar]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH v1] ARM: dts: aspeed: ast2600-evb: Enable RX delay for MAC0/MAC1
Date
Hi Joel

> > +&syscon {
> > + mac0-clk-delay = <0x10 0x0a
> > + 0x10 0x10
> > + 0x10 0x10>;
>
> These properties aren't supported by the mainline kernel. Do you have some
> code coming for that support?
No, clk-ast2600 did not support it yet.
Let me remove this setting for now since I confirmed that the patch wouldn't be ready very soon.
Currently, the delay will be set at u-boot stage with commit for OpenBMC https://github.com/openbmc/u-boot/commit/e40a4e447a0e7f4d8b38c3256349e39ff3701f1f
So it should be safe for OpenBMC if this part was removed.

> -----Original Message-----
> From: Joel Stanley <joel@jms.id.au>
> Sent: Friday, March 18, 2022 4:46 PM
> To: Howard Chiu <howard_chiu@aspeedtech.com>
> Cc: robh+dt@kernel.org; andrew@aj.id.au; devicetree@vger.kernel.org;
> linux-arm-kernel@lists.infradead.org; linux-aspeed@lists.ozlabs.org;
> linux-kernel@vger.kernel.org; Troy Lee <troy_lee@aspeedtech.com>
> Subject: Re: [PATCH v1] ARM: dts: aspeed: ast2600-evb: Enable RX delay for
> MAC0/MAC1
>
> Hi Howard,
>
> On Fri, 18 Mar 2022 at 08:09, Howard Chiu <howard_chiu@aspeedtech.com>
> wrote:
> >
> > Since mac0/1 and mac2/3 are physically located on different die, they
> > have different properties by nature, which is mac0/1 has smaller delay step.
> >
> > The property 'phy-mode' on ast2600 mac0 and mac1 is recommended to set
> to 'rgmii-rxid'
> > which enables the RX interface delay from the PHY chip.
> > Refer page 45 of SDK User Guide v08.00
> >
> https://github.com/AspeedTech-BMC/openbmc/releases/download/v08.00/SD
> K
> > _User_Guide_v08.00.pdf
> >
> > Set mac delay according to the mactest result.
>
> This bit confused me. How does the rxid relate to the mac delay numbers?
> Which device and code is responsible for using them?
>
> >
> > Signed-off-by: Howard Chiu <howard_chiu@aspeedtech.com>
> > ---
> > arch/arm/boot/dts/aspeed-ast2600-evb.dts | 19 +++++++++++++++++--
> > 1 file changed, 17 insertions(+), 2 deletions(-)
> >
> > diff --git a/arch/arm/boot/dts/aspeed-ast2600-evb.dts
> > b/arch/arm/boot/dts/aspeed-ast2600-evb.dts
> > index b7eb552640cb..db16ba307e97 100644
> > --- a/arch/arm/boot/dts/aspeed-ast2600-evb.dts
> > +++ b/arch/arm/boot/dts/aspeed-ast2600-evb.dts
> > @@ -103,7 +103,7 @@ ethphy3: ethernet-phy@0 {
> > &mac0 {
> > status = "okay";
> >
> > - phy-mode = "rgmii";
> > + phy-mode = "rgmii-rxid";
> > phy-handle = <&ethphy0>;
> >
> > pinctrl-names = "default";
> > @@ -114,7 +114,7 @@ &mac0 {
> > &mac1 {
> > status = "okay";
> >
> > - phy-mode = "rgmii";
> > + phy-mode = "rgmii-rxid";
> > phy-handle = <&ethphy1>;
> >
> > pinctrl-names = "default";
> > @@ -141,6 +141,21 @@ &mac3 {
> > pinctrl-0 = <&pinctrl_rgmii4_default>; };
> >
> > +&syscon {
> > + mac0-clk-delay = <0x10 0x0a
> > + 0x10 0x10
> > + 0x10 0x10>;
>
> These properties aren't supported by the mainline kernel. Do you have some
> code coming for that support?
>
> > + mac1-clk-delay = <0x10 0x0a
> > + 0x10 0x10
> > + 0x10 0x10>;
> > + mac2-clk-delay = <0x08 0x04
> > + 0x08 0x04
> > + 0x08 0x04>;
> > + mac3-clk-delay = <0x08 0x04
> > + 0x08 0x04
> > + 0x08 0x04>;
> > +};
> > +
> > &emmc_controller {
> > status = "okay";
> > };
> > --
> > 2.25.1
> >
\
 
 \ /
  Last update: 2022-03-18 10:34    [W:0.178 / U:0.556 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site