lkml.org 
[lkml]   [2022]   [Mar]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v1 09/14] ARM: dts: imx6dl-colibri: Move common nodes to SoM dtsi
Date
The following two nodes define module level functionality, move
them from the carrier board dts file to the SoM file.
While at it, reorder the properties in the gpio-keys node alphabetical.

- gpio-keys defining the wakeup pin
- memory node

The atmel touchscreen node can be used on any carrier board.
Move it from the carrier board to the module-level device tree and
keep it disabled.
Set the default pinmuxing to the dedicated connector available
on newer carrier boards and rename the pinctrl labels specifying
the INT/Reset signal to a common pattern.
pinctrl_atmel_conn - uses 107/106 pins as used on dedicated connector
pinctrl_atmel_adap - uses 28/30 pins as used with jumper wires

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
---

arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts | 49 ------------------
arch/arm/boot/dts/imx6qdl-colibri.dtsi | 53 ++++++++++++++++++++
2 files changed, 53 insertions(+), 49 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts b/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
index 535b5c156229..dff2d35e693b 100644
--- a/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
+++ b/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
@@ -17,12 +17,6 @@
compatible = "toradex,colibri_imx6dl-eval-v3", "toradex,colibri_imx6dl",
"fsl,imx6dl";

- /* Will be filled by the bootloader */
- memory@10000000 {
- device_type = "memory";
- reg = <0x10000000 0>;
- };
-
aliases {
i2c0 = &i2c2;
i2c1 = &i2c3;
@@ -44,20 +38,6 @@
clock-frequency = <16000000>;
clock-output-names = "clk16m";
};
-
- gpio-keys {
- compatible = "gpio-keys";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_gpio_keys>;
-
- wakeup {
- label = "Wake-Up";
- gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>; /* SODIMM 45 */
- linux,code = <KEY_WAKEUP>;
- debounce-interval = <10>;
- wakeup-source;
- };
- };
};

/* Colibri SSP */
@@ -81,21 +61,6 @@
&i2c3 {
status = "okay";

- /*
- * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
- * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
- */
- touchscreen@4a {
- compatible = "atmel,maxtouch";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pcap_1>;
- reg = <0x4a>;
- interrupt-parent = <&gpio1>;
- interrupts = <9 IRQ_TYPE_EDGE_FALLING>; /* SODIMM 28 */
- reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>; /* SODIMM 30 */
- status = "disabled";
- };
-
/* M41T0M6 real time clock on carrier board */
rtc_i2c: rtc@68 {
compatible = "st,m41t0";
@@ -111,20 +76,6 @@
&pinctrl_weim_gpio_5 &pinctrl_weim_gpio_6
&pinctrl_usbh_oc_1 &pinctrl_usbc_id_1
>;
-
- pinctrl_pcap_1: pcap1grp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0 /* SODIMM 28 */
- MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0 /* SODIMM 30 */
- >;
- };
-
- pinctrl_mxt_ts: mxttsgrp {
- fsl,pins = <
- MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x130b0 /* SODIMM 107 */
- MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x130b0 /* SODIMM 106 */
- >;
- };
};

&pwm1 {
diff --git a/arch/arm/boot/dts/imx6qdl-colibri.dtsi b/arch/arm/boot/dts/imx6qdl-colibri.dtsi
index 3459bfb5c60b..1c49fd3e6286 100644
--- a/arch/arm/boot/dts/imx6qdl-colibri.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-colibri.dtsi
@@ -23,6 +23,20 @@
status = "disabled";
};

+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_keys>;
+
+ wakeup {
+ debounce-interval = <10>;
+ gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>; /* SODIMM 45 */
+ label = "Wake-Up";
+ linux,code = <KEY_WAKEUP>;
+ wakeup-source;
+ };
+ };
+
lcd_display: disp0 {
compatible = "fsl,imx-parallel-display";
interface-pix-fmt = "bgr666";
@@ -50,6 +64,12 @@
};
};

+ /* Will be filled by the bootloader */
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0>;
+ };
+
panel_dpi: panel-dpi {
/*
* edt,et057090dhu: EDT 5.7" LCD TFT
@@ -564,6 +584,17 @@
scl-gpios = <&gpio1 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
status = "disabled";
+
+ atmel_mxt_ts: touchscreen@4a {
+ compatible = "atmel,maxtouch";
+ interrupt-parent = <&gpio2>;
+ interrupts = <24 IRQ_TYPE_EDGE_FALLING>; /* SODIMM 107 */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_atmel_conn>;
+ reg = <0x4a>;
+ reset-gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>; /* SODIMM 106 */
+ status = "disabled";
+ };
};

&ipu1_di0_disp0 {
@@ -682,6 +713,28 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbh_oc_1>;

+ /* Atmel MXT touchsceen + Capacitive Touch Adapter */
+ /* NOTE: This pin group conflicts with pin groups
+ * pinctrl_pwm1/pinctrl_pwm4. Don't use them simultaneously.
+ */
+ pinctrl_atmel_adap: atmeladaptergrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__GPIO1_IO09 0xb0b1 /* SODIMM 28 */
+ MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0xb0b1 /* SODIMM 30 */
+ >;
+ };
+
+ /* Atmel MXT touchsceen + boards with built-in Capacitive Touch Connector */
+ /* NOTE: This pin group conflicts with pin groups pinctrl_weim_cs1 and
+ * pinctrl_weim_cs2. Don't use them simultaneously.
+ */
+ pinctrl_atmel_conn: atmelconnectorgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0xb0b1 /* SODIMM_107 */
+ MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0xb0b1 /* SODIMM_106 */
+ >;
+ };
+
pinctrl_audmux: audmuxgrp {
fsl,pins = <
MX6QDL_PAD_KEY_COL0__AUD5_TXC 0x130b0
--
2.20.1
\
 
 \ /
  Last update: 2022-03-14 17:32    [W:0.143 / U:0.460 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site