lkml.org 
[lkml]   [2022]   [Feb]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 07/20] bus: mhi: ep: Add support for creating and destroying MHI EP devices
On Wed, Jan 05, 2022 at 06:28:08PM -0600, Alex Elder wrote:
> On 12/2/21 5:35 AM, Manivannan Sadhasivam wrote:
> > This commit adds support for creating and destroying MHI endpoint devices.
> > The MHI endpoint devices binds to the MHI endpoint channels and are used
> > to transfer data between MHI host and endpoint device.
> >
> > There is a single MHI EP device for each channel pair. The devices will be
> > created when the corresponding channels has been started by the host and
> > will be destroyed during MHI EP power down and reset.
> >
> > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> > ---
> > drivers/bus/mhi/ep/main.c | 85 +++++++++++++++++++++++++++++++++++++++
> > 1 file changed, 85 insertions(+)
> >
> > diff --git a/drivers/bus/mhi/ep/main.c b/drivers/bus/mhi/ep/main.c
> > index ce0f99f22058..f0b5f49db95a 100644
> > --- a/drivers/bus/mhi/ep/main.c
> > +++ b/drivers/bus/mhi/ep/main.c
> > @@ -63,6 +63,91 @@ static struct mhi_ep_device *mhi_ep_alloc_device(struct mhi_ep_cntrl *mhi_cntrl)
> > return mhi_dev;
> > }
> > +static int mhi_ep_create_device(struct mhi_ep_cntrl *mhi_cntrl, u32 ch_id)
> > +{
> > + struct mhi_ep_device *mhi_dev;
> > + struct mhi_ep_chan *mhi_chan = &mhi_cntrl->mhi_chan[ch_id];
> > + int ret;
> > +
> > + mhi_dev = mhi_ep_alloc_device(mhi_cntrl);
> > + if (IS_ERR(mhi_dev))
> > + return PTR_ERR(mhi_dev);
> > +
> > + mhi_dev->dev_type = MHI_DEVICE_XFER;
>
> Elsewhere (at least in mhi_ep_process_tre_ring()) in your code
> you assume that the even-numbered channel is UL.
>
> I would say, either use that assumption throughout, or do
> not use that assumption at all. (I prefer the latter.)
>
> I don't really like how this assumes that the channels
> are defined in adjacent pairs. It assumes one is
> upload and the next one is download, but doesn't
> specify the order in which they're defined. If
> you're going to assume they are defined in pairs, you
> should be able to assume which one is defined first,
> and then simplify this code (and even verify that
> they are defined UL before DL, perhaps).
>

Yes, the UL channel is always even numbered and DL is odd.
I've removed the checks.

> > + /* Configure primary channel */
> > + if (mhi_chan->dir == DMA_TO_DEVICE) {
> > + mhi_dev->ul_chan = mhi_chan;
> > + mhi_dev->ul_chan_id = mhi_chan->chan;
> > + } else {
> > + mhi_dev->dl_chan = mhi_chan;
> > + mhi_dev->dl_chan_id = mhi_chan->chan;
> > + }
> > +
> > + get_device(&mhi_dev->dev);
> > + mhi_chan->mhi_dev = mhi_dev;
> > +
> > + /* Configure secondary channel as well */
> > + mhi_chan++;
> > + if (mhi_chan->dir == DMA_TO_DEVICE) {
> > + mhi_dev->ul_chan = mhi_chan;
> > + mhi_dev->ul_chan_id = mhi_chan->chan;
> > + } else {
> > + mhi_dev->dl_chan = mhi_chan;
> > + mhi_dev->dl_chan_id = mhi_chan->chan;
> > + }
> > +
> > + get_device(&mhi_dev->dev);
> > + mhi_chan->mhi_dev = mhi_dev;
> > +
> > + /* Channel name is same for both UL and DL */
>
> You could verify the two channels indeed have the
> same name.
>

done.

Thanks,
Mani

\
 
 \ /
  Last update: 2022-02-03 16:15    [W:0.156 / U:0.140 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site