lkml.org 
[lkml]   [2022]   [Feb]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [RFC PATCH 08/13] KVM: SVM: Do not update logical APIC ID table when in x2APIC mode
From
Date
On Sun, 2022-02-20 at 20:19 -0600, Suravee Suthikulpanit wrote:
> In X2APIC mode the Logical Destination Register is read-only,
> which provides a fixed mapping between the logical and physical
> APIC IDs. Therefore, there is no Logical APIC ID table in X2AVIC
> and the processor uses the X2APIC ID in the backing page to create
> a vCPU’s logical ID.
>
> Therefore, add logic to check x2APIC mode before updating logical
> APIC ID table.
>
> Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
> ---
> arch/x86/kvm/svm/avic.c | 11 ++++++++++-
> 1 file changed, 10 insertions(+), 1 deletion(-)
>
> diff --git a/arch/x86/kvm/svm/avic.c b/arch/x86/kvm/svm/avic.c
> index 215d8a7dbc1d..55b3b703b93b 100644
> --- a/arch/x86/kvm/svm/avic.c
> +++ b/arch/x86/kvm/svm/avic.c
> @@ -417,6 +417,10 @@ static int avic_ldr_write(struct kvm_vcpu *vcpu, u8 g_physical_id, u32 ldr)
> bool flat;
> u32 *entry, new_entry;
>
> + /* Note: x2AVIC does not use logical APIC ID table */
> + if (apic_x2apic_mode(vcpu->arch.apic))
> + return 0;
> +
> flat = kvm_lapic_get_reg(vcpu->arch.apic, APIC_DFR) == APIC_DFR_FLAT;
> entry = avic_get_logical_id_entry(vcpu, ldr, flat);
> if (!entry)
> @@ -435,8 +439,13 @@ static void avic_invalidate_logical_id_entry(struct kvm_vcpu *vcpu)
> {
> struct vcpu_svm *svm = to_svm(vcpu);
> bool flat = svm->dfr_reg == APIC_DFR_FLAT;
> - u32 *entry = avic_get_logical_id_entry(vcpu, svm->ldr_reg, flat);
> + u32 *entry;
> +
> + /* Note: x2AVIC does not use logical APIC ID table */
> + if (apic_x2apic_mode(vcpu->arch.apic))
> + return;
>
> + entry = avic_get_logical_id_entry(vcpu, svm->ldr_reg, flat);
> if (entry)
> clear_bit(AVIC_LOGICAL_ID_ENTRY_VALID_BIT, (unsigned long *)entry);
> }


Here actually the good apic_x2apic_mode was used.

However, shouldn't we inject #GP in avic_ldr_write to make this read realy read-only?
It might be too late to do so here, since most AVIC writes are trap like.

Thus we need to make the msr that corresponds to LDR to be write protected in the msr bitmap,
and inject #GP when write it attempted.

Then we can add WARN_ON in this function for this case instead.

Best regards,
Maxim Levitsky

\
 
 \ /
  Last update: 2022-02-24 18:42    [W:0.324 / U:0.532 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site