lkml.org 
[lkml]   [2022]   [Feb]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Subject[PATCH] net: ipv6: ensure we call ipv6_mc_down() at most once
From
Date
There are two reasons for addrconf_notify() to be called with NETDEV_DOWN:
either the network device is actually going down, or IPv6 was disabled
on the interface.

If either of them stays down while the other is toggled, we repeatedly
call the code for NETDEV_DOWN, including ipv6_mc_down(), while never
calling the corresponding ipv6_mc_up() in between. This will cause a
new entry in idev->mc_tomb to be allocated for each multicast group
the interface is subscribed to, which in turn leaks one struct ifmcaddr6
per nontrivial multicast group the interface is subscribed to.

The following reproducer will leak at least $n objects:

ip addr add ff2e::4242/32 dev eth0 autojoin
sysctl -w net.ipv6.conf.eth0.disable_ipv6=1
for i in $(seq 1 $n); do
ip link set up eth0; ip link set down eth0
done

Joining groups with IPV6_ADD_MEMBERSHIP (unprivileged) or setting the
sysctl net.ipv6.conf.eth0.forwarding to 1 (=> subscribing to ff02::2)
can also be used to create a nontrivial idev->mc_list, which will the
leak objects with the right up-down-sequence.

Based on both sources for NETDEV_DOWN events the interface IPv6 state
should be considered:

- not ready if the network interface is not ready OR IPv6 is disabled
for it
- ready if the network interface is ready AND IPv6 is enabled for it

The functions ipv6_mc_up() and ipv6_down() should only be run when this
state changes.

Implement this by remembering when the IPv6 state is ready, and only
run ipv6_mc_down() if it actually changed from ready to not ready.

The other direction (not ready -> ready) already works correctly, as:

- the interface notification triggered codepath for NETDEV_UP /
NETDEV_CHANGE returns early if ipv6 is disabled, and
- the disable_ipv6=0 triggered codepath skips fully initializing the
interface as long as addrconf_link_ready(dev) returns false
- calling ipv6_mc_up() repeatedly does not leak anything

Fixes: 3ce62a84d53c ("ipv6: exit early in addrconf_notify() if IPv6 is disabled")
Signed-off-by: Johannes Nixdorf <j.nixdorf@avm.de>
---
net/ipv6/addrconf.c | 8 ++++++--
1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/net/ipv6/addrconf.c b/net/ipv6/addrconf.c
index f927c199a93c..c5e9ca244175 100644
--- a/net/ipv6/addrconf.c
+++ b/net/ipv6/addrconf.c
@@ -3732,6 +3732,7 @@ static int addrconf_ifdown(struct net_device *dev, bool unregister)
struct inet6_dev *idev;
struct inet6_ifaddr *ifa, *tmp;
bool keep_addr = false;
+ bool was_ready;
int state, i;

ASSERT_RTNL();
@@ -3797,7 +3798,10 @@ static int addrconf_ifdown(struct net_device *dev, bool unregister)

addrconf_del_rs_timer(idev);

- /* Step 2: clear flags for stateless addrconf */
+ /* Step 2: clear flags for stateless addrconf, repeated down
+ * detection
+ */
+ was_ready = idev->if_flags & IF_READY;
if (!unregister)
idev->if_flags &= ~(IF_RS_SENT|IF_RA_RCVD|IF_READY);

@@ -3871,7 +3875,7 @@ static int addrconf_ifdown(struct net_device *dev, bool unregister)
if (unregister) {
ipv6_ac_destroy_dev(idev);
ipv6_mc_destroy_dev(idev);
- } else {
+ } else if (was_ready) {
ipv6_mc_down(idev);
}

--
2.35.1
\
 
 \ /
  Last update: 2022-02-24 10:17    [W:0.049 / U:0.520 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site