lkml.org 
[lkml]   [2022]   [Feb]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH net-next v2 1/1] net: dsa: microchip: ksz9477: implement MTU configuration
On Wed, Feb 23, 2022 at 09:40:55AM +0100, Oleksij Rempel wrote:
> This chips supports two ways to configure max MTU size:
> - by setting SW_LEGAL_PACKET_DISABLE bit: if this bit is 0 allowed packed size
> will be between 64 and bytes 1518. If this bit is 1, it will accept
> packets up to 2000 bytes.
> - by setting SW_JUMBO_PACKET bit. If this bit is set, the chip will
> ignore SW_LEGAL_PACKET_DISABLE value and use REG_SW_MTU__2 register to
> configure MTU size.
>
> Current driver has disabled SW_JUMBO_PACKET bit and activates
> SW_LEGAL_PACKET_DISABLE. So the switch will pass all packets up to 2000 without
> any way to configure it.
>
> By providing port_change_mtu we are switch to SW_JUMBO_PACKET way and will
> be able to configure MTU up to ~9000.
>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
> changes v2:
> - rename max_mtu to max_frame and new_mtu to frame_size
> - use max() instead of if(>)
> ---
> drivers/net/dsa/microchip/ksz9477.c | 40 +++++++++++++++++++++++--
> drivers/net/dsa/microchip/ksz9477_reg.h | 4 +++
> drivers/net/dsa/microchip/ksz_common.h | 1 +
> 3 files changed, 43 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/net/dsa/microchip/ksz9477.c b/drivers/net/dsa/microchip/ksz9477.c
> index 18ffc8ded7ee..5c5f78cb970e 100644
> --- a/drivers/net/dsa/microchip/ksz9477.c
> +++ b/drivers/net/dsa/microchip/ksz9477.c
> @@ -11,6 +11,7 @@
> #include <linux/platform_data/microchip-ksz.h>
> #include <linux/phy.h>
> #include <linux/if_bridge.h>
> +#include <linux/if_vlan.h>
> #include <net/dsa.h>
> #include <net/switchdev.h>
>
> @@ -182,6 +183,33 @@ static void ksz9477_port_cfg32(struct ksz_device *dev, int port, int offset,
> bits, set ? bits : 0);
> }
>
> +static int ksz9477_change_mtu(struct dsa_switch *ds, int port, int mtu)
> +{
> + struct ksz_device *dev = ds->priv;
> + u16 frame_size, max_frame = 0;
> + int i;
> +
> + frame_size = mtu + ETH_HLEN + VLAN_HLEN + ETH_FCS_LEN;

Are you sure the unit of measurement is ok? My KSZ9477 documentation
says this about register 0x0308:

Maximum Frame Length (MTU)
Specifies the maximum transmission unit (MTU), which is the maximum
frame payload size. Frames which exceed this maximum are truncated. This
value can be set as high as 9000 (= 0x2328) if jumbo frame support is
required.

"frame payload" to me means what MTU should mean. And ETH_HLEN +
VLAN_HLEN + ETH_FCS_LEN isn't part of that meaning.

> +
> + if (dsa_is_cpu_port(ds, port))
> + frame_size += KSZ9477_INGRESS_TAG_LEN;
> +
> + /* Cache the per-port MTU setting */
> + dev->ports[port].max_frame = frame_size;
> +
> + for (i = 0; i < dev->port_cnt; i++)
> + max_frame = max(max_frame, dev->ports[i].max_frame);
> +
> + return regmap_update_bits(dev->regmap[1], REG_SW_MTU__2,
> + REG_SW_MTU_MASK, max_frame);
> +}
> +
> +static int ksz9477_max_mtu(struct dsa_switch *ds, int port)
> +{
> + return KSZ9477_MAX_FRAME_SIZE - ETH_HLEN - ETH_FCS_LEN - VLAN_HLEN -
> + KSZ9477_INGRESS_TAG_LEN;
> +}
> +
> static int ksz9477_wait_vlan_ctrl_ready(struct ksz_device *dev)
> {
> unsigned int val;
> @@ -1412,8 +1440,14 @@ static int ksz9477_setup(struct dsa_switch *ds)
> /* Do not work correctly with tail tagging. */
> ksz_cfg(dev, REG_SW_MAC_CTRL_0, SW_CHECK_LENGTH, false);
>
> - /* accept packet up to 2000bytes */
> - ksz_cfg(dev, REG_SW_MAC_CTRL_1, SW_LEGAL_PACKET_DISABLE, true);
> + /* Enable REG_SW_MTU__2 reg by setting SW_JUMBO_PACKET */
> + ksz_cfg(dev, REG_SW_MAC_CTRL_1, SW_JUMBO_PACKET, true);
> +
> + /* Now we can configure default MTU value */
> + ret = regmap_update_bits(dev->regmap[1], REG_SW_MTU__2, REG_SW_MTU_MASK,
> + VLAN_ETH_FRAME_LEN + ETH_FCS_LEN);

Why do you need this? Doesn't DSA call dsa_slave_create() ->
dsa_slave_change_mtu(ETH_DATA_LEN) on probe?

> + if (ret)
> + return ret;
>
> ksz9477_config_cpu_port(ds);
>
> @@ -1460,6 +1494,8 @@ static const struct dsa_switch_ops ksz9477_switch_ops = {
> .port_mirror_add = ksz9477_port_mirror_add,
> .port_mirror_del = ksz9477_port_mirror_del,
> .get_stats64 = ksz9477_get_stats64,
> + .port_change_mtu = ksz9477_change_mtu,
> + .port_max_mtu = ksz9477_max_mtu,
> };
>
> static u32 ksz9477_get_port_addr(int port, int offset)
> diff --git a/drivers/net/dsa/microchip/ksz9477_reg.h b/drivers/net/dsa/microchip/ksz9477_reg.h
> index 16939f29faa5..2278e763ee3e 100644
> --- a/drivers/net/dsa/microchip/ksz9477_reg.h
> +++ b/drivers/net/dsa/microchip/ksz9477_reg.h
> @@ -176,6 +176,7 @@
> #define REG_SW_MAC_ADDR_5 0x0307
>
> #define REG_SW_MTU__2 0x0308
> +#define REG_SW_MTU_MASK GENMASK(13, 0)
>
> #define REG_SW_ISP_TPID__2 0x030A
>
> @@ -1662,4 +1663,7 @@
> /* 148,800 frames * 67 ms / 100 */
> #define BROADCAST_STORM_VALUE 9969
>
> +#define KSZ9477_INGRESS_TAG_LEN 2
> +#define KSZ9477_MAX_FRAME_SIZE 9000
> +
> #endif /* KSZ9477_REGS_H */
> diff --git a/drivers/net/dsa/microchip/ksz_common.h b/drivers/net/dsa/microchip/ksz_common.h
> index c6fa487fb006..739365bfceb2 100644
> --- a/drivers/net/dsa/microchip/ksz_common.h
> +++ b/drivers/net/dsa/microchip/ksz_common.h
> @@ -41,6 +41,7 @@ struct ksz_port {
>
> struct ksz_port_mib mib;
> phy_interface_t interface;
> + u16 max_frame;
> };
>
> struct ksz_device {
> --
> 2.30.2
>

\
 
 \ /
  Last update: 2022-02-24 00:39    [W:0.069 / U:0.192 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site