lkml.org 
[lkml]   [2022]   [Dec]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 3/3] arm64: dts: ti: k3-am625-sk: Add support for USB
Date
From: Aswath Govindraju <a-govindraju@ti.com>

AM62 SoC has two instances of USB and they are brought on to the board
in the following way,

-> USB0 instance
- This is brought out to a USB TypeC connector on board through TPS6598 PD
controller. The PD controller should decide the role based on CC pin in
the connector. Unfortunately the irq line for the TPS isn't hooked up
which is a mode not yet support by the driver (some patches were
submitted earlier this year[0]). So for now the PD controller is left
out and periphal mode chosen.

-> USB1 instance
- This is brought out to a USB TypeA connector on board.

Therefore, add the required device tree support for the above in the board
dts file.

0: https://lore.kernel.org/lkml/f714ee55-ef47-317d-81b9-57020dda064b@ti.com/T/

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
[merge from vendor bsp, drop TPS6598 support, reword commit message]
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>

---

Changes in v2:
- Rebase against linux-next 20221220

arch/arm64/boot/dts/ti/k3-am625-sk.dts | 50 ++++++++++++++++++++++++++
1 file changed, 50 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am625-sk.dts b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
index 4f179b146cab..c82a0ebf6772 100644
--- a/arch/arm64/boot/dts/ti/k3-am625-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
@@ -24,6 +24,8 @@ aliases {
spi0 = &ospi0;
ethernet0 = &cpsw_port1;
ethernet1 = &cpsw_port2;
+ usb0 = &usb0;
+ usb1 = &usb1;
};

chosen {
@@ -284,6 +286,12 @@ main_gpio1_ioexp_intr_pins_default: main-gpio1-ioexp-intr-pins-default {
AM62X_IOPAD(0x01d4, PIN_INPUT, 7) /* (B15) UART0_RTSn.GPIO1_23 */
>;
};
+
+ main_usb1_pins_default: main-usb1-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x0258, PIN_OUTPUT, 0) /* (F18) USB1_DRVVBUS */
+ >;
+ };
};

&wkup_uart0 {
@@ -464,3 +472,45 @@ partition@3fc0000 {
};
};
};
+
+&ecap0 {
+ status = "disabled";
+};
+
+&ecap1 {
+ status = "disabled";
+};
+
+&ecap2 {
+ status = "disabled";
+};
+
+&main_mcan0 {
+ status = "disabled";
+};
+
+&epwm0 {
+ status = "disabled";
+};
+
+&epwm1 {
+ status = "disabled";
+};
+
+&epwm2 {
+ status = "disabled";
+};
+
+&usbss0 {
+ ti,vbus-divider;
+};
+
+&usb0 {
+ dr_mode = "peripheral";
+};
+
+&usb1 {
+ dr_mode = "host";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_usb1_pins_default>;
+};
--
2.39.0
\
 
 \ /
  Last update: 2023-03-26 23:16    [W:0.035 / U:0.376 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site