lkml.org 
[lkml]   [2022]   [Dec]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v6 tty-next 3/4] serial: 8250_pci1xxxx: Add RS485 support to quad-uart driver
On Thu, 1 Dec 2022, Kumaravel Thiagarajan wrote:

> pci1xxxx uart supports RS485 mode of operation in the hardware with
> auto-direction control with configurable delay for releasing RTS after
> the transmission. This patch adds support for the RS485 mode.
>
> Co-developed-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
> Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
> Signed-off-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
> ---
> Changes in v6:
> - Modified datatype of delay_in_baud_periods to u64 to avoid overflows
>
> Changes in v5:
> - Removed unnecessary assignments
> - Corrected styling issues in comments
>
> Changes in v4:
> - No Change
>
> Changes in v3:
> - Remove flags sanitization in driver which is taken care in core
>
> Changes in v2:
> - move pci1xxxx_rs485_config to a separate patch with
> pci1xxxx_rs485_supported.
> ---
> drivers/tty/serial/8250/8250_pci1xxxx.c | 49 +++++++++++++++++++++++++
> 1 file changed, 49 insertions(+)
>
> diff --git a/drivers/tty/serial/8250/8250_pci1xxxx.c b/drivers/tty/serial/8250/8250_pci1xxxx.c
> index d5037e76b636..7585066d6baf 100644
> --- a/drivers/tty/serial/8250/8250_pci1xxxx.c
> +++ b/drivers/tty/serial/8250/8250_pci1xxxx.c
> @@ -145,6 +145,53 @@ static void pci1xxxx_set_divisor(struct uart_port *port, unsigned int baud,
> port->membase + UART_BAUD_CLK_DIVISOR_REG);
> }
>
> +static int pci1xxxx_rs485_config(struct uart_port *port,
> + struct ktermios *termios,
> + struct serial_rs485 *rs485)
> +{
> + u32 clock_div = readl(port->membase + UART_BAUD_CLK_DIVISOR_REG);

Maybe move this into the block where it's needed?

> + u64 delay_in_baud_periods;
> + u32 baud_period_in_ns;
> + u32 data = 0;

data seems a bit too generic name for a variable? At minimum I'd suggest
using cfg or mode_cfg (I couldn't guess where ADCL comes from, perhaps it
has some component which would make the variable name better).

> +
> + /*
> + * pci1xxxx's uart hardware supports only RTS delay after
> + * Tx and in units of bit times to a maximum of 15
> + */
> + if (rs485->flags & SER_RS485_ENABLED) {
> + data = ADCL_CFG_EN | ADCL_CFG_PIN_SEL;
> +
> + if (!(rs485->flags & SER_RS485_RTS_ON_SEND))
> + data |= ADCL_CFG_POL_SEL;
> +
> + if (rs485->delay_rts_after_send) {
> + baud_period_in_ns =
> + FIELD_GET(BAUD_CLOCK_DIV_INT_MSK, clock_div) *
> + UART_BIT_SAMPLE_CNT;
> + delay_in_baud_periods =
> + rs485->delay_rts_after_send * NSEC_PER_MSEC /
> + baud_period_in_ns;
> + delay_in_baud_periods =
> + min_t(u64, delay_in_baud_periods,
> + FIELD_MAX(ADCL_CFG_RTS_DELAY_MASK));
> + data |= FIELD_PREP(ADCL_CFG_RTS_DELAY_MASK,
> + delay_in_baud_periods);
> + rs485->delay_rts_after_send =
> + baud_period_in_ns * delay_in_baud_periods /
> + NSEC_PER_MSEC;
> + }
> + }
> + writel(data, port->membase + ADCL_CFG_REG);
> + return 0;
> +}
> +
> +static const struct serial_rs485 pci1xxxx_rs485_supported = {
> + .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND |
> + SER_RS485_RTS_AFTER_SEND,
> + .delay_rts_after_send = 1,
> + /* Delay RTS before send is not supported */
> +};
> +
> static int pci1xxxx_setup(struct pci1xxxx_8250 *priv,
> struct uart_8250_port *port, int port_idx)
> {
> @@ -155,6 +202,8 @@ static int pci1xxxx_setup(struct pci1xxxx_8250 *priv,
> port->port.set_termios = serial8250_do_set_termios;
> port->port.get_divisor = pci1xxxx_get_divisor;
> port->port.set_divisor = pci1xxxx_set_divisor;
> + port->port.rs485_config = pci1xxxx_rs485_config;
> + port->port.rs485_supported = pci1xxxx_rs485_supported;
>
> ret = serial8250_pci_setup_port(priv->pdev, port, 0, port_idx * 256, 0);
> if (ret < 0)
>

Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>

--
i.
\
 
 \ /
  Last update: 2022-12-01 10:48    [W:0.104 / U:0.172 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site