lkml.org 
[lkml]   [2022]   [Nov]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH v2 1/2] dt-bindings: iio: addac: add AD74115
On Thu, Nov 03, 2022 at 11:44:35AM +0200, Cosmin Tanislav wrote:
> From: Cosmin Tanislav <cosmin.tanislav@analog.com>
>
> The AD74115H is a single-channel, software-configurable, input and
> output device for industrial control applications. The AD74115H
> provides a wide range of use cases, integrated on a single chip.
>
> These use cases include analog output, analog input, digital output,
> digital input, resistance temperature detector (RTD), and thermocouple
> measurement capability. The AD74115H also has an integrated HART modem.
>
> A serial peripheral interface (SPI) is used to handle all communications
> to the device, including communications with the HART modem. The digital
> input and digital outputs can be accessed via the SPI or the
> general-purpose input and output (GPIO) pins to support higher
> speed data rates.
>
> The device features a 16-bit, sigma-delta analog-to-digital converter
> (ADC) and a 14-bit digital-to-analog converter (DAC).
> The AD74115H contains a high accuracy 2.5 V on-chip reference that can
> be used as the DAC and ADC reference.
>
> Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
> ---
> .../bindings/iio/addac/adi,ad74115.yaml | 370 ++++++++++++++++++
> MAINTAINERS | 7 +
> 2 files changed, 377 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/iio/addac/adi,ad74115.yaml
>
> diff --git a/Documentation/devicetree/bindings/iio/addac/adi,ad74115.yaml b/Documentation/devicetree/bindings/iio/addac/adi,ad74115.yaml
> new file mode 100644
> index 000000000000..621f11d5c1f3
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/addac/adi,ad74115.yaml
> @@ -0,0 +1,370 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/iio/addac/adi,ad74115.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Analog Devices AD74115H device
> +
> +maintainers:
> + - Cosmin Tanislav <cosmin.tanislav@analog.com>
> +
> +description: |
> + The AD74115H is a single-channel software configurable input/output
> + device for industrial control applications. It contains functionality for
> + analog output, analog input, digital output, digital input, resistance
> + temperature detector, and thermocouple measurements integrated into a single
> + chip solution with an SPI interface. The device features a 16-bit ADC and a
> + 14-bit DAC.
> +
> + https://www.analog.com/en/products/ad74115h.html
> +
> +properties:
> + compatible:
> + enum:
> + - adi,ad74115h
> +
> + reg:
> + maxItems: 1
> +
> + '#address-cells':
> + const: 1
> +
> + '#size-cells':
> + const: 0
> +
> + spi-max-frequency:
> + maximum: 24000000
> +
> + spi-cpol: true
> +
> + reset-gpios: true
> +
> + interrupts:
> + maxItems: 1
> +
> + avdd-supply: true
> + avcc-supply: true
> + dvcc-supply: true
> + aldo1v8-supply: true
> + dovdd-supply: true
> + refin-supply: true
> +
> + adi,ch-func:
> + $ref: /schemas/types.yaml#/definitions/uint32
> + description: |
> + Channel function.
> + 0 - High impedance
> + 1 - Voltage output
> + 2 - Current output
> + 3 - Voltage input
> + 4 - Current input, externally-powered
> + 5 - Current input, loop-powered
> + 6 - Resistance input
> + 7 - RTD measure
> + 8 - Digital input logic
> + 9 - Digital input, loop-powered
> + 10 - Current output with HART
> + 11 - Current input, externally-powered, with HART
> + 12 - Current input, loop-powered, with HART
> + minimum: 0
> + maximum: 12
> + default: 0
> +
> + adi,conv2-mux:
> + $ref: /schemas/types.yaml#/definitions/uint32
> + description: |
> + Input node for ADC conversion 2.
> + 0 - SENSE_EXT1 to AGND_SENSE
> + 1 - SENSE_EXT2 to AGND_SENSE
> + 2 - SENSE_EXT2 to SENSE_EXT1
> + 3 - AGND to AGND
> + minimum: 0
> + maximum: 3
> + default: 0
> +
> + adi,conv2-range:
> + $ref: /schemas/types.yaml#/definitions/uint32
> + description: |
> + Conversion range for ADC conversion 2.
> + 0 - 0V to 12V
> + 1 - -12V to +12V
> + 2 - -2.5V to +2.5V
> + 3 - -2.5V to 0V
> + 4 - 0V to 2.5V
> + 5 - 0V to 0.625V
> + 6 - -104mV to +104mV
> + 7 - 0V to 12V
> + minimum: 0
> + maximum: 7
> + default: 0
> +
> + adi,sense-agnd-buffer-lp:
> + type: boolean
> + description: |

Don't need '|' if no formatting to preserve.

> + Whether to enable low-power buffered mode for the AGND sense pin.
> +
> + adi,lf-buffer-lp:
> + type: boolean
> + description: |
> + Whether to enable low-power buffered mode for the low-side filtered
> + sense pin.
> +
> + adi,hf-buffer-lp:
> + type: boolean
> + description: |
> + Whether to enable low-power buffered mode for the high-side filtered
> + sense pin.
> +
> + adi,ext2-buffer-lp:
> + type: boolean
> + description: Whether to enable low-power buffered mode for the EXT2 pin.
> +
> + adi,ext1-buffer-lp:
> + type: boolean
> + description: Whether to enable low-power buffered mode for the EXT1 pin.
> +
> + adi,comparator-invert:
> + type: boolean
> + description: Whether to invert the comparator output.
> +
> + adi,digital-input-sink-range-high:
> + $ref: /schemas/types.yaml#/definitions/uint32
> + description: |
> + When not present, the digital input range is from 0 to 3700uA in steps
> + of 120uA, with a ~2k series resistance.
> + When present, the digital input range is from 0 to 7400uA in steps
> + of 240uA, with a ~1k series resistance.
> +
> + adi,digital-input-sink-microamp:
> + description: Sink current in digital input mode.
> + minimum: 0
> + maximum: 3700
> + default: 0
> +
> + adi,digital-input-debounce-mode-counter-reset:
> + type: boolean
> + description: |
> + When not present, a counter increments when the signal is asserted
> + and decrements when the signal is de-asserted.
> + When present, a counter increments while the signal is asserted and
> + resets when the signal de-asserts
> +
> + adi,digital-input-unbuffered:
> + type: boolean
> + description: Whether to buffer digital input signals.
> +
> + adi,digital-input-short-circuit-detection:
> + type: boolean
> + description: Whether to detect digital input short circuits.
> +
> + adi,digital-input-open-circuit-detection:
> + type: boolean
> + description: Whether to detect digital input open circuits.
> +
> + adi,digital-input-threshold-mode-fixed:
> + type: boolean
> + description: |
> + When not present, the digital input threshold range is -0.96 * AVDD
> + to AVDD.
> + When present, the threshold range is fixed from -19V to 30V.
> +
> + adi,dac-bipolar:
> + type: boolean
> + description: |
> + When not present, the DAC operates in the 0V to 12V range.
> + When present, the DAC operates in the -12V to 12V range.
> +
> + adi,charge-pump:
> + type: boolean
> + description: Whether to enable the internal charge pump.
> +
> + adi,dac-hart-slew:
> + type: boolean
> + description: Whether to use a HART-compatible slew rate.
> +
> + adi,dac-current-limit-low:
> + type: boolean
> + description: |
> + When not present, the DAC short-circuit current limit is 32mA in
> + either source or sink for VOUT and 4mA sink for IOUT.
> + When present, the limit is 16mA in either source or sink for VOUT,
> + 1mA sink for IOUT.
> +
> + adi,4-wire-rtd:
> + type: boolean
> + description: |
> + When not present, the ADC should be used for measuring 3-wire RTDs.
> + When present, the ADC should be used for measuring 4-wire RTDs.
> +
> + adi,3-wire-rtd-excitation-swap:
> + type: boolean
> + description: Whether to swap the excitation for 3-wire RTD.
> +
> + adi,rtd-excitation-current-microamp:
> + description: Excitation current to apply to RTD.
> + enum: [250, 500, 750, 1000]
> + default: 250
> +
> + adi,ext1-burnout:
> + type: boolean
> + description: Whether to enable burnout current for EXT1.
> +
> + adi,ext1-burnout-current-nanoamp:
> + $ref: /schemas/types.yaml#/definitions/uint32
> + description: |
> + Burnout current in nanoamps to be applied to EXT1.
> + enum: [0, 50, 500, 1000, 10000]
> + default: 0
> +
> + adi,ext1-burnout-current-polarity-sourcing:
> + type: boolean
> + description: |
> + When not present, the burnout current polarity for EXT1 is sinking.
> + When present, the burnout current polarity for EXT1 is sourcing.
> +
> + adi,ext2-burnout:
> + type: boolean
> + description: Whether to enable burnout current for EXT2.
> +
> + adi,ext2-burnout-current-nanoamp:
> + $ref: /schemas/types.yaml#/definitions/uint32
> + description: Burnout current in nanoamps to be applied to EXT2.
> + enum: [0, 50, 500, 1000, 10000]
> + default: 0
> +
> + adi,ext2-burnout-current-polarity-sourcing:
> + type: boolean
> + description: |
> + When not present, the burnout current polarity for EXT2 is sinking.
> + When present, the burnout current polarity for EXT2 is sourcing.
> +
> + adi,viout-burnout:
> + type: boolean
> + description: Whether to enable burnout current for VIOUT.
> +
> + adi,viout-burnout-current-nanoamp:
> + $ref: /schemas/types.yaml#/definitions/uint32
> + description: Burnout current in nanoamps to be applied to VIOUT.
> + enum: [0, 1000, 10000]
> + default: 0
> +
> + adi,viout-burnout-current-polarity-sourcing:
> + type: boolean
> + description: |
> + When not present, the burnout current polarity for VIOUT is sinking.
> + When present, the burnout current polarity for VIOUT is sourcing.
> +
> + adi,gpio0-mode:
> + $ref: /schemas/types.yaml#/definitions/uint32
> + description: |
> + GPIO functions.
> + 0 - Disabled
> + 1 - Logic I/O
> + 2 - Comparator output
> + 3 - Control HART CD
> + 4 - Monitor HART CD
> + 5 - Monitor HART EOM status
> + minimum: 0
> + maximum: 5
> + default: 0
> +
> + adi,gpio1-mode:
> + $ref: /schemas/types.yaml#/definitions/uint32
> + description: |
> + GPIO functions.
> + 0 - Disabled
> + 1 - Logic I/O
> + 2 - Drive external digital output FET
> + 3 - Control HART RXD
> + 4 - Monitor HART RXD
> + 5 - Monitor HART SOM status
> + minimum: 0
> + maximum: 5
> + default: 0
> +
> + adi,gpio2-mode:
> + $ref: /schemas/types.yaml#/definitions/uint32
> + description: |
> + GPIO functions.
> + 0 - Disabled
> + 1 - Logic I/O
> + 2 - Drive internal digital output FET
> + 3 - Control HART TXD
> + 4 - Monitor HART TXD
> + 5 - Monitor HART TX complete status
> + minimum: 0
> + maximum: 5
> + default: 0
> +
> + adi,gpio3-mode:
> + $ref: /schemas/types.yaml#/definitions/uint32
> + description: |
> + GPIO functions.
> + 0 - Disabled
> + 1 - Logic I/O
> + 2 - High impedance
> + 3 - Control HART RTS
> + 4 - Monitor HART RTS
> + 5 - Monitor HART CD complete status
> + minimum: 0
> + maximum: 5
> + default: 0
> +
> +required:
> + - compatible
> + - reg
> + - spi-cpol
> + - avdd-supply
> +
> +allOf:
> + - $ref: /schemas/spi/spi-peripheral-props.yaml#
> + - if:
> + properties:
> + adi,digital-input-sink-range-high: true

The 'if' is true if adi,digital-input-sink-range-high is not present
which is probably not what you want. Use 'required' instead.

> + then:
> + properties:
> + adi,digital-input-sink-microamp:
> + maximum: 7400
> +
> +additionalProperties: false

As pointed out, yes, this needs to be unevaluatedProperties.

> +
> +examples:
> + - |
> + #include <dt-bindings/gpio/gpio.h>
> + #include <dt-bindings/interrupt-controller/irq.h>
> +
> + spi {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + addac@0 {
> + compatible = "adi,ad74115h";
> + reg = <0>;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + spi-max-frequency = <12000000>;
> + spi-cpol;
> +
> + reset-gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
> +
> + interrupt-parent = <&gpio>;
> + interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
> +
> + avdd-supply = <&ad74115_avdd>;
> +
> + adi,ch-func = <1>;
> + adi,conv2-mux = <2>;
> + adi,conv2-range = <1>;
> +
> + adi,gpio0-mode = <1>;
> + adi,gpio1-mode = <1>;
> + adi,gpio2-mode = <1>;
> + adi,gpio3-mode = <1>;
> +
> + adi,dac-bipolar;
> + };
> + };
> +...
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 7a56c344ca67..5b5533f54f67 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -1175,6 +1175,13 @@ W: https://ez.analog.com/linux-software-drivers
> F: Documentation/devicetree/bindings/iio/adc/adi,ad7780.yaml
> F: drivers/iio/adc/ad7780.c
>
> +ANALOG DEVICES INC AD74115 DRIVER
> +M: Cosmin Tanislav <cosmin.tanislav@analog.com>
> +L: linux-iio@vger.kernel.org
> +S: Supported
> +W: http://ez.analog.com/community/linux-device-drivers
> +F: Documentation/devicetree/bindings/iio/addac/adi,ad74115.yaml
> +
> ANALOG DEVICES INC AD74413R DRIVER
> M: Cosmin Tanislav <cosmin.tanislav@analog.com>
> L: linux-iio@vger.kernel.org
> --
> 2.38.1
>
>

\
 
 \ /
  Last update: 2022-11-07 17:45    [W:1.262 / U:0.212 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site