lkml.org 
[lkml]   [2022]   [Nov]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3 tty-next 2/3] 8250: microchip: pci1xxxx: Add rs485 support to quad-uart driver
Date
pci1xxxx uart supports rs485 mode of operation in the hardware with
auto-direction control with configurable delay for releasing RTS after
the transmission. This patch adds support for the rs485 mode.

Signed-off-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
---
Changes in v3:
- Remove flags sanitization in driver which is taken care in core

Changes in v2:
- move pci1xxxx_rs485_config to a separate patch with
pci1xxxx_rs485_supported.
---
drivers/tty/serial/8250/8250_pci1xxxx.c | 49 +++++++++++++++++++++++++
1 file changed, 49 insertions(+)

diff --git a/drivers/tty/serial/8250/8250_pci1xxxx.c b/drivers/tty/serial/8250/8250_pci1xxxx.c
index e74e8d63daee..ed3418feb262 100644
--- a/drivers/tty/serial/8250/8250_pci1xxxx.c
+++ b/drivers/tty/serial/8250/8250_pci1xxxx.c
@@ -137,6 +137,53 @@ static void pci1xxxx_set_divisor(struct uart_port *port, unsigned int baud,
port->membase + UART_BAUD_CLK_DIVISOR_REG);
}

+static int pci1xxxx_rs485_config(struct uart_port *port,
+ struct ktermios *termios,
+ struct serial_rs485 *rs485)
+{
+ u32 clock_div = readl(port->membase + UART_BAUD_CLK_DIVISOR_REG);
+ u8 delay_in_baud_periods = 0;
+ u32 baud_period_in_ns = 0;
+ u32 data = 0;
+
+ /* pci1xxxx's uart hardware supports only RTS delay after
+ * Tx and in units of bit times to a maximum of 15
+ */
+ if (rs485->flags & SER_RS485_ENABLED) {
+ data = ADCL_CFG_EN | ADCL_CFG_PIN_SEL;
+
+ if (!(rs485->flags & SER_RS485_RTS_ON_SEND))
+ data |= ADCL_CFG_POL_SEL;
+
+ if (rs485->delay_rts_after_send) {
+ baud_period_in_ns =
+ FIELD_GET(BAUD_CLOCK_DIV_INT_MSK, clock_div) *
+ UART_BIT_SAMPLE_CNT;
+ delay_in_baud_periods =
+ (rs485->delay_rts_after_send * NSEC_PER_MSEC) /
+ baud_period_in_ns;
+ delay_in_baud_periods =
+ min_t(u8, delay_in_baud_periods,
+ FIELD_MAX(ADCL_CFG_RTS_DELAY_MASK));
+ data |= FIELD_PREP(ADCL_CFG_RTS_DELAY_MASK,
+ delay_in_baud_periods);
+ rs485->delay_rts_after_send =
+ (baud_period_in_ns * delay_in_baud_periods) /
+ NSEC_PER_MSEC;
+ rs485->delay_rts_before_send = 0;
+ }
+ }
+ writel(data, port->membase + ADCL_CFG_REG);
+ return 0;
+}
+
+static const struct serial_rs485 pci1xxxx_rs485_supported = {
+ .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND |
+ SER_RS485_RTS_AFTER_SEND,
+ .delay_rts_after_send = 1,
+ /* Delay RTS before send is not supported */
+};
+
static int pci1xxxx_setup(struct pci1xxxx_8250 *priv,
struct uart_8250_port *port, int idx)
{
@@ -186,6 +233,8 @@ static int pci1xxxx_setup(struct pci1xxxx_8250 *priv,
port->port.set_termios = serial8250_do_set_termios;
port->port.get_divisor = pci1xxxx_get_divisor;
port->port.set_divisor = pci1xxxx_set_divisor;
+ port->port.rs485_config = pci1xxxx_rs485_config;
+ port->port.rs485_supported = pci1xxxx_rs485_supported;
ret = pci_setup_port(priv->dev, port, 0, offset, 0);
if (ret < 0)
return ret;
--
2.25.1
\
 
 \ /
  Last update: 2022-11-07 13:46    [W:0.071 / U:0.448 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site