lkml.org 
[lkml]   [2022]   [Nov]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v1 2/3] Documentation: gpio: Add a section on what to return in ->get() callback
From
Hi again,

On 11/30/22 17:12, Hans de Goede wrote:
> Hi,
>
> On 11/30/22 16:55, Andy Shevchenko wrote:
>> The ->get() callback depending on other settings and hardware support
>> may return different values, while the line outside the chip is kept
>> in the same state. Let's discuss that in the documentation.
>>
>> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
>> ---
>> Documentation/driver-api/gpio/driver.rst | 24 ++++++++++++++++++++++++
>> 1 file changed, 24 insertions(+)
>>
>> diff --git a/Documentation/driver-api/gpio/driver.rst b/Documentation/driver-api/gpio/driver.rst
>> index bf6319cc531b..3d2f36001a7a 100644
>> --- a/Documentation/driver-api/gpio/driver.rst
>> +++ b/Documentation/driver-api/gpio/driver.rst
>> @@ -251,6 +251,30 @@ supports more versatile control over electrical properties and can handle
>> different pull-up or pull-down resistance values.
>>
>>
>> +Considerations of the ->get() returned value
>> +--------------------------------------------
>> +
>> +Due to different possible electrical configurations and software applications
>> +the value that ->get() callback returns may vary depending on the other settings.
>> +This will allow to use pins in the I2C emulation mode or other not so standard
>> +uses.
>> +
>> +The below table gathered the most used cases.
>> +
>> +========== ========== =============== =======================
>> + Input Output State What value to return?
>> +========== ========== =============== =======================
>> + Disabled Disabled Hi-Z input buffer
>> + Disabled OS/OD/etc Single ended [cached] output buffer
>
> You need to clarify what single-ended means here. You mean a pin
> which is only capable of output I guess ? So now way to figure
> out if another participant in the OS/OD bus has its transistor
> in the "on" state this pulling the bus high / low agains the bias
> resistor(s) which determine the state of the bus in rest ?
>
> Or you mean that the bus is uni-directional? Even then being
> able to detect a short-circuit is useful.
>
>> + x Push-Pull Out [cached] output buffer
>
> Why, most GPIO drivers are protected against short-circuit to
> GND / Vdd and actually reading the input-buffer here will allow
> GPIO API consumers to detect such short-circuits if they are
> interested in this. This would e.g. be useful to detect
> mis-wiring on devices like the Raspberry Pi were users often
> connect extra peripherals through breadboards.
>
> IMHO for pins with an input buffer get() should simply
> always return the contents of the input buffer. This is what
> I believe almost all GPIO drivers currently do and also
> keeps the get() methods KISS.
>
> Actually implementing the behavior you suggest here requires
> the get() method to differentiate between push-pull and
> other mode. This makes the get() method implementation
> needlessly complicated and will likely be a source of bugs
> as people will get this wrong in some cases and people
> will very likely not test all possible combinations from
> this big table you are adding here.
>
> IHMO the rules for get() should simply be:
>
> 1. Device has an input buffer:
> Return input-buffer value for the pin.
>
> 2. Devices does not have an input buffer:
> Return last set output-buffer value

Quick correction device should be pin here, because it
if there is an input buffer or not can differ per pin.
So IHMO the rules for get() should simply be:

1. pin has an input buffer:
return input-buffer value for the pin.

2. pin does not have an input buffer:
return the value last set for the pin's output-buffer

Regards,

Hans



>> + Enabled Disabled In input buffer
>> + Enabled OS/OD/etc Bidirectional input buffer
>> +========== ========== =============== =======================
>> +
>> +The [cached] here is used in a broader sense: either pure software cache, or
>> +read back value from the GPIO output buffer (not all hardware support that).
>> +
>> +
>> GPIO drivers providing IRQs
>> ===========================
>>
>

\
 
 \ /
  Last update: 2022-11-30 17:16    [W:0.110 / U:0.208 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site