lkml.org 
[lkml]   [2022]   [Nov]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [RESEND PATCH 2/2] arm64: dts: qcom: sdm632-fairphone-fp3: Add NFC
From


On 29.11.2022 19:31, Luca Weiss wrote:
> On Dienstag, 29. November 2022 14:29:36 CET Konrad Dybcio wrote:
>> On 28.11.2022 18:37, Luca Weiss wrote:
>>> Configure the node for the NQ310 chip found on this device, which is
>>> compatible with generic nxp-nci-i2c driver.
>>>
>>> Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
>>> ---
>>> RESEND to fix Cc
>>>
>>> arch/arm64/boot/dts/qcom/sdm632-fairphone-fp3.dts | 15 +++++++++++++++
>>> 1 file changed, 15 insertions(+)
>>>
>>> diff --git a/arch/arm64/boot/dts/qcom/sdm632-fairphone-fp3.dts
>>> b/arch/arm64/boot/dts/qcom/sdm632-fairphone-fp3.dts index
>>> 2920504461d3..fde93cbcd180 100644
>>> --- a/arch/arm64/boot/dts/qcom/sdm632-fairphone-fp3.dts
>>> +++ b/arch/arm64/boot/dts/qcom/sdm632-fairphone-fp3.dts
>>> @@ -63,6 +63,21 @@ touchscreen@48 {
>>>
>>> };
>>>
>>> };
>>>
>>> +&i2c_5 {
>>> + status = "okay";
>>> +
>>> + nfc@28 {
>>> + compatible = "nxp,nq310", "nxp,nxp-nci-i2c";
>>
>> Unless there was some binding change (that was not emailed to me with
>> this email, I only got 2/2), only "nxp,nxp-nci-i2c" and
>> "nxp,pn547", "nxp,nxp-nci-i2c" are allowed.
>
> Yes, I've added the double compatible to the yaml.
> https://lore.kernel.org/lkml/20221128173744.833018-1-luca@z3ntu.xyz/
Ok, this looks good then.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>


>
> I'll try to work on my Cc-script setup, currently it adds the output of
> get_maintainers.pl for each patch (and adds all for the cover letter), which
> is based on some script I found a while ago online.
>
> Is there like a recommended way to put all people in Cc for a series, I'm not
> aware of anything at least...
>
> Perhaps I'll look into b4 for sending patches, that seems to have some goodies
> there.
Check out this reply from Rob Herring here https://lore.kernel.org/lkml/CAL_JsqLubWBr2W3xZPsuPLOGav7CFgBdH=aCfT22F_m0_cx3cQ@mail.gmail.com/

Konrad
>
> Regards
> Luca
>
>>
>> The node looks good though.
>>
>> Konrad
>>
>>> + reg = <0x28>;
>>> +
>>> + interrupt-parent = <&tlmm>;
>>> + interrupts = <17 IRQ_TYPE_LEVEL_HIGH>;
>>> +
>>> + enable-gpios = <&tlmm 16 GPIO_ACTIVE_HIGH>;
>>> + firmware-gpios = <&tlmm 62 GPIO_ACTIVE_HIGH>;
>>> + };
>>> +};
>>> +
>>>
>>> &pm8953_resin {
>>>
>>> status = "okay";
>>> linux,code = <KEY_VOLUMEDOWN>;
>
>
>
>

\
 
 \ /
  Last update: 2022-11-30 15:21    [W:0.037 / U:1.504 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site