lkml.org 
[lkml]   [2022]   [Nov]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v4 03/10] arm64: dts: qcom: Add pm8010 pmic dtsi
Date
From: Neil Armstrong <neil.armstrong@linaro.org>

Add nodes for pm8010 in separate dtsi file.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
arch/arm64/boot/dts/qcom/pm8010.dtsi | 84 ++++++++++++++++++++++++++++
1 file changed, 84 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/pm8010.dtsi

diff --git a/arch/arm64/boot/dts/qcom/pm8010.dtsi b/arch/arm64/boot/dts/qcom/pm8010.dtsi
new file mode 100644
index 000000000000..0ea641e12209
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pm8010.dtsi
@@ -0,0 +1,84 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+ thermal-zones {
+ pm8010-m-thermal {
+ polling-delay-passive = <100>;
+ polling-delay = <0>;
+
+ thermal-sensors = <&pm8010_m_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pm8010-n-thermal {
+ polling-delay-passive = <100>;
+ polling-delay = <0>;
+
+ thermal-sensors = <&pm8010_n_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+ };
+};
+
+
+&spmi_bus {
+ pm8010_m: pmic@c {
+ compatible = "qcom,pm8010", "qcom,spmi-pmic";
+ reg = <0xc SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8010_m_temp_alarm: temp-alarm@2400 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0x2400>;
+ interrupts = <0xc 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+ };
+
+ pm8010_n: pmic@d {
+ compatible = "qcom,pm8010", "qcom,spmi-pmic";
+ reg = <0xd SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8010_n_temp_alarm: temp-alarm@2400 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0x2400>;
+ interrupts = <0xd 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+ };
+};
--
2.34.1
\
 
 \ /
  Last update: 2022-11-30 11:19    [W:0.069 / U:1.120 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site