lkml.org 
[lkml]   [2022]   [Nov]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v6 7/7] drm/bridge: it6505: Register Type C mode switches
On Thu, Nov 24, 2022 at 06:20:56PM +0800, Pin-yen Lin wrote:
> Register USB Type-C mode switches when the "mode-switch" property and
> relevant port are available in Device Tree. Configure the "lane_swap"
> state based on the entered alternate mode for a specific Type-C
> connector, which ends up updating the lane swap registers of the it6505
> chip.

...

> config DRM_ITE_IT6505
> tristate "ITE IT6505 DisplayPort bridge"
> depends on OF
> + depends on TYPEC || TYPEC=n
> select DRM_DISPLAY_DP_HELPER
> select DRM_DISPLAY_HDCP_HELPER
> select DRM_DISPLAY_HELPER

Something went wrong with the indentation. Perhaps you need to fix it first.

...

> #include <drm/drm_edid.h>
> #include <drm/drm_print.h>
> #include <drm/drm_probe_helper.h>
> +#include <drm/drm_of.h>

Make it ordered?

...

> +struct it6505_port_data {

> + bool dp_connected;

Perhaps make it last?

> + struct typec_mux_dev *typec_mux;
> + struct it6505 *it6505;
> +};

...

> +static void it6505_typec_ports_update(struct it6505 *it6505)
> +{
> + usleep_range(3000, 4000);
> +
> + if (it6505->typec_ports[0].dp_connected && it6505->typec_ports[1].dp_connected)
> + /* Both ports available, do nothing to retain the current one. */
> + return;
> + else if (it6505->typec_ports[0].dp_connected)
> + it6505->lane_swap = false;
> + else if (it6505->typec_ports[1].dp_connected)
> + it6505->lane_swap = true;
> +
> + usleep_range(3000, 4000);
> +}

As per previous patch comments.

Also, comment out these long sleeps. Why they are needed.

...

> + int ret = pm_runtime_get_sync(dev);
> +
> + /*
> + * On system resume, mux_set can be triggered before
> + * pm_runtime_force_resume re-enables runtime power management.

We refer to the functions as func().

> + * Handling the error here to make sure the bridge is powered on.
> + */
> + if (ret < 0)
> + it6505_poweron(it6505);

This seems needed a bit more of explanation, esp. why you leave PM runtime
reference count bumped up.

...

> + num_lanes = drm_of_get_data_lanes_count(node, 0, 2);
> + if (num_lanes <= 0) {
> + dev_err(dev, "Error on getting data lanes count: %d\n",
> + num_lanes);
> + return num_lanes;
> + }
> +
> + ret = of_property_read_u32_array(node, "data-lanes", dp_lanes, num_lanes);
> + if (ret) {
> + dev_err(dev, "Failed to read the data-lanes variable: %d\n",
> + ret);
> + return ret;
> + }
> +
> + for (i = 0; i < num_lanes; i++) {
> + if (port_num != -1 && port_num != dp_lanes[i] / 2) {
> + dev_err(dev, "Invalid data lane numbers\n");
> + return -EINVAL;
> + }

As per previous patch comments.

> + port_num = dp_lanes[i] / 2;
> + }

The above seems like tons of duplicating code that drivers need to implement.
Can we shrink that burden by adding some library functions?

--
With Best Regards,
Andy Shevchenko


\
 
 \ /
  Last update: 2022-11-24 13:24    [W:0.613 / U:0.040 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site