lkml.org 
[lkml]   [2022]   [Nov]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v2 7/8] riscv: dts: starfive: Add StarFive JH7110 VisionFive2 board device tree
From
On Sat, 19 Nov 2022 01:55:40 +0800, Emil Renner Berthing wrote:
> On Fri, 18 Nov 2022 at 02:17, Hal Feng <hal.feng@starfivetech.com> wrote:
>>
>> From: Emil Renner Berthing <kernel@esmil.dk>
>>
>> Add a minimal device tree for StarFive JH7110 VisionFive2 board.
> Missing space between VisionFive and 2.

Will fix accordingly.

>
>> Support booting and basic clock/reset/pinctrl/uart drivers.
>>
>> Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
>> Co-developed-by: Jianlong Huang <jianlong.huang@starfivetech.com>
>> Signed-off-by: Jianlong Huang <jianlong.huang@starfivetech.com>
>> Co-developed-by: Hal Feng <hal.feng@starfivetech.com>
>> Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
>> ---
>> arch/riscv/boot/dts/starfive/Makefile | 1 +
>> .../jh7110-starfive-visionfive-v2.dts | 116 ++++++++++++++++++
>> 2 files changed, 117 insertions(+)
>> create mode 100644 arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-v2.dts
>>
>> diff --git a/arch/riscv/boot/dts/starfive/Makefile b/arch/riscv/boot/dts/starfive/Makefile
>> index 0ea1bc15ab30..e1237dbc6aac 100644
>> --- a/arch/riscv/boot/dts/starfive/Makefile
>> +++ b/arch/riscv/boot/dts/starfive/Makefile
>> @@ -1,2 +1,3 @@
>> # SPDX-License-Identifier: GPL-2.0
>> dtb-$(CONFIG_SOC_STARFIVE) += jh7100-beaglev-starlight.dtb
>> +dtb-$(CONFIG_SOC_STARFIVE) += jh7110-starfive-visionfive-v2.dtb
>> diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-v2.dts b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-v2.dts
>> new file mode 100644
>> index 000000000000..c8946cf3a268
>> --- /dev/null
>> +++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-v2.dts
>> @@ -0,0 +1,116 @@
>> +// SPDX-License-Identifier: GPL-2.0 OR MIT
>> +/*
>> + * Copyright (C) 2022 StarFive Technology Co., Ltd.
>> + * Copyright (C) 2022 Emil Renner Berthing <kernel@esmil.dk>
>> + */
>> +
>> +/dts-v1/;
>> +#include "jh7110.dtsi"
>> +#include <dt-bindings/gpio/gpio.h>
>> +#include <dt-bindings/pinctrl/pinctrl-starfive-jh7110.h>
>> +
>> +/ {
>> + model = "StarFive VisionFive V2";
>> + compatible = "starfive,visionfive-v2", "starfive,jh7110";
>
> Again, please consult your colleagues if you're calling the board
> "VisionFive 2" or "VisionFive V2" and name the file, model and board
> accordingly.

Will fix accordingly. Please see the record of patch 1.

>
>> + aliases {
>> + serial0 = &uart0;
>> + };
>> +
>> + chosen {
>> + linux,initrd-start = <0x46100000>;
>> + linux,initrd-end = <0x4c000000>;
>
> These two lines don't belong here. They're added by the bootloader dynamically.

OK, will delete. Thanks.

>
>> + stdout-path = "serial0:115200";
>
> You're missing a n8.

Will fix.

>
>> + };
>> +
>> + cpus {
>> + timebase-frequency = <4000000>;
>> + };
>> +
>> + memory@40000000 {
>> + device_type = "memory";
>> + reg = <0x0 0x40000000 0x1 0x0>;
>> + };
>> +
>> + gpio-restart {
>> + compatible = "gpio-restart";
>> + gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
>> + priority = <224>;
>> + };
>> +};
>> +
>> +&osc {
>> + clock-frequency = <24000000>;
>> +};
>> +
>> +&clk_rtc {
>> + clock-frequency = <32768>;
>> +};
>> +
>> +&gmac0_rmii_refin {
>> + clock-frequency = <50000000>;
>> +};
>> +
>> +&gmac0_rgmii_rxin {
>> + clock-frequency = <125000000>;
>> +};
>> +
>> +&gmac1_rmii_refin {
>> + clock-frequency = <50000000>;
>> +};
>> +
>> +&gmac1_rgmii_rxin {
>> + clock-frequency = <125000000>;
>> +};
>> +
>> +&i2stx_bclk_ext {
>> + clock-frequency = <12288000>;
>> +};
>> +
>> +&i2stx_lrck_ext {
>> + clock-frequency = <192000>;
>> +};
>> +
>> +&i2srx_bclk_ext {
>> + clock-frequency = <12288000>;
>> +};
>> +
>> +&i2srx_lrck_ext {
>> + clock-frequency = <192000>;
>> +};
>> +
>> +&tdm_ext {
>> + clock-frequency = <49152000>;
>> +};
>> +
>> +&mclk_ext {
>> + clock-frequency = <12288000>;
>> +};
>> +
>> +&gpio {
>> + uart0_pins: uart0-0 {
>> + tx-pins {
>> + pinmux = <GPIOMUX(5, GPOUT_SYS_UART0_TX, GPOEN_ENABLE, GPI_NONE)>;
>> + bias-disable;
>> + drive-strength = <12>;
>> + input-disable;
>> + input-schmitt-disable;
>> + slew-rate = <0>;
>> + };
>> +
>> + rx-pins {
>> + pinmux = <GPIOMUX(6, GPOUT_LOW, GPOEN_DISABLE, GPI_SYS_UART0_RX)>;
>> + bias-pull-up;
>
> There are external pull-ups, so maybe change this line to
>
> bias-disable; /* external pull-up */

Good job. Will fix it later.

Best regards,
Hal

>
>> + drive-strength = <2>;
>> + input-enable;
>> + input-schmitt-enable;
>> + slew-rate = <0>;
>> + };
>> + };
>> +};
>> +
>> +&uart0 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&uart0_pins>;
>> + status = "okay";
>> +};

\
 
 \ /
  Last update: 2022-11-24 07:18    [W:0.059 / U:1.704 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site