lkml.org 
[lkml]   [2022]   [Nov]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH RESEND] can: j1939: do not wait 250ms if the same addr was already claimed
On Wed, Nov 23, 2022 at 09:39:06PM +0100, Devid Antonio Filoni wrote:
> On Mon, 2022-11-21 at 06:19 +0100, Oleksij Rempel wrote:
> > On Sun, Nov 20, 2022 at 08:18:32PM +0100, Devid Antonio Filoni wrote:
> > > On Sun, 2022-11-20 at 09:45 +0100, Oleksij Rempel wrote:
> > > > On Sun, Nov 20, 2022 at 01:11:52AM +0100, Devid Antonio Filoni wrote:
> > > > > On Sat, 2022-11-19 at 11:12 +0100, Oleksij Rempel wrote:
> > > > > > On Fri, Nov 18, 2022 at 04:12:40PM +0100, Devid Antonio Filoni wrote:
> > > > > > > Hi Oleksij,
> > > > > > >
> > > > > > > honestly I would apply proposed patch because it is the easier solution
> > > > > > > and makes the driver compliant with the standard for the following
> > > > > > > reasons:
> > > > > > > - on the first claim, the kernel will wait 250 ms as stated by the
> > > > > > > standard
> > > > > > > + on successive claims with the same name, the kernel will not wait
> > > > > > > 250ms, this implies:
> > > > > > > - it will not wait after sending the address-claimed message when the
> > > > > > > claimed address has been spoofed, but the standard does not explicitly
> > > > > > > states what to do in this case (see previous emails in this thread), so
> > > > > > > it would be up to the application developer to decide how to manage the
> > > > > > > conflict
> > > > > > > - it will not wait after sending the address-claimed message when a
> > > > > > > request for address-claimed message has been received as stated by the
> > > > > > > standard
> > > > > >
> > > > > > Standard says:
> > > > > > 1. No CF _shall_ begin, or resume, transmission on the network until 250 ms
> > > > > > after it has successfully claimed an address (Figure 4).
> > > > > > 2. This does not apply when responding to a request for address claimed.
> > > > > >
> > > > > > With current patch state: 1. is implemented and working as expected, 2.
> > > > > > is not implemented.
> > > > > > With this patch: 1. is partially broken and 2. is partially faking
> > > > > > needed behavior.
> > > > > >
> > > > > > It will not wait if remote ECU which rebooted for some reasons. With this patch
> > > > > > we are breaking one case of the standard in favor to fake compatibility to the
> > > > > > other case. We should avoid waiting only based on presence of RfAC not based
> > > > > > on the old_addr == new_addr.
> > > > >
> > > > > I'm sorry, I don't think I understood the point about reboot ("It will
> > > > > not wait if remote ECU which rebooted for some reasons"). If another ECU
> > > > > rebooted, then *it* will have to perform the claim procedure again
> > > > > waiting 250 ms before beginning the transmission. Your ECU doesn't have
> > > > > to check if the other ECUs respected the 250 ms wait.
> > > >
> > > > With proposed patch:
> > > > - local application which is sending to the remote NAME, will start or continue
> > > > communication with ECU which should stay silent.
> > >
> > > And this is not forbidden by the standard, the standard states that the
> > > remote ECU shall not start or continue the communication but it can
> > > *receive* messages.
> > > For example, what would you do if:
> > > - during the 250 ms wait, another ECU sends a request-for-address-
> > > claimed message meant to the address you're claiming?
> > > From "4.5.3 Other requirements for initialization":
> > > A CF shall respond to a request-for-address-claimed message when the
> > > destination address is the same as the CF's address and shall transmit
> > > its response to the Global address (255).
> > > - during the 250 ms wait another ECU sends a normal message (non
> > > address-claim related) using the SA you're currently claiming?
> > >
> > > > - local application which was manually or automatically restarted (see
> > > > application watchdogs), will bypass address claim procedure
> > > > completion and start sending without 250ms delay.
> > >
> > > Then the application will be violating the standard, you're right,
> > > however please note that, as per driver implementation, each time the
> > > socket is closed and opened again (if bound with a name) you have to
> > > send the address-claimed message again.
> > > The standard also states how to treat this kind of violations on the
> > > remote ECU side.
> > >
> > > >
> > > > > Also, the ISO11783-5 standard, with "Figure 6 (Resolving address
> > > > > contention between two self-configurable-address CF)" of "4.5.4.2 -
> > > > > Address-claim prioritization", shows that:
> > > > > - ECU1 claims the address (time: 0 ms)
> > > > > - ECU2 claims the same address (time: 0+x ms)
> > > > > - ECU1 NAME has the higher priority, so ECU1 sends again the address
> > > > > claimed message as soon as it received the address-claim from ECU2
> > > > > (time: 0+x+y ms)
> > > > > - ECU1 starts normal transmission (time: 250 ms)
> > > > > With current implementation, the ECU1 would start the transmission at
> > > > > time 0+x+y+250 ms, with proposed patch it would not.
> > > >
> > > > You are right, this should be fixed.
> > > > But proposed patch closes one issues and opens another, with this patch it will
> > > > be enough to send at least two address claimed messages to bypass the delay.
> > >
> > > No, because the timer associated with the first claim *is not stopped*.
> > >
> > > >
> > > > > Same is showed in "Figure 7 (Resolving address contention between a non-
> > > > > configurable address CF and a self-configurable address CF)", the ECU
> > > > > waits again 250 ms only when claiming a different address.
> > > >
> > > > Ack
> > > >
> > > > > Also, as previously discussed in this thread, the standard states in
> > > > > 4.4.4.3 - Address violation:
> > > > > If a CF receives a message, other than the address-claimed message,
> > > > > which uses the CF's own SA,
> > > > > then the CF:
> > > > > - shall send the address-claim message to the Global address;
> > > > > - shall activate a diagnostic trouble code with SPN = 2000+SA and FMI =
> > > > > 31
> > > > > It is not *explicitly* stated that you have to wait 250 ms after the
> > > > > address-claim message has been sent.
> > > >
> > > > There is no need to explicitly state it. The requirement is clearly described
> > > > in the 4.5.2.d part 1 with clearly defined exception in 4.5.2.d part 2.
> > > > If something is not explicitly stated, the stated requirement has always
> > > > priority.
> > > >
> > > > > Please note that the 250 ms wait is mentioned only in "4.5 - Network
> > > > > initialization"
> > > >
> > > > OK, we need to refer to the wording used in a specifications, in
> > > > general:
> > > > Shall – Shall is used to designate a mandatory requirement.
> > > > Should – Should is used for requirements that are considered good and are
> > > > recommended, but are not absolutely mandatory.
> > > > May – May is used to for requirements that are optional.
> > > >
> > > > If a requirement with strong wording as "shall" is not strong enough for
> > > > you and you are suing words as ".. mentioned only in .." then even a
> > > > statistical analysis of this spec will have no meaning. In all
> > > > cases we can just invalidate all arguments by using: it is only X or Y.
> > > >
> > > > > while above statements come from "4.4 - Network-management procedures".
> > > > > Also in this case, the proposed patch is still standard compliant.
> > > >
> > > > If we remove 4.5.2.d from the spec, then yes.
> > > >
> > > > > So I'm sorry but I have to disagree with you, there are many things
> > > > > broken in the current implementation because it is forcing the 250 wait
> > > > > to all cases but it should not.
> > > >
> > > > If we remove 4.5.2.d from the spec, then yes. Every construction is
> > > > logical if we adopt input variables to the construction.
> > >
> > > From "4.4.4.3 - Address violation":
> > > - *shall send the address-claim message* to the Global address
> > > From "4.5.2 Address claim requirements":
> > > - No CF shall begin, or resume, transmission on the network until 250 ms
> > > after it has successfully *claimed an address*, except when responding
> > > to a request for address-claimed.
> > >
> > > Do you see any difference?
> > > With your interpretation of the standard, then above 4.5.2.d sentence
> > > shall be:
> > > - No CF shall begin, or resume, transmission on the network until 250 ms
> > > after it has successfully *sent the address-claim message*, except when
> > > responding to a request for address-claimed.
> > >
> > > I think "it has successfully claimed an address" is valid for the whole
> > > claim procedure and not for the address-claimed message only.
> > >
> > > Please note that the ECU shall send the address-claim message also when
> > > it receives a request for a matching NAME ("4.4.3.2 NAME management (NM)
> > > message"). This does not mean that is claiming again the address.
> > >
> > > >
> > > > > > Without words 2. part should be implemented without breaking 1.
> > > > > >
> > > > > > > Otherwise you will have to keep track of above cases and decide if the
> > > > > > > wait is needed or not, but this is hard do accomplish because is the
> > > > > > > application in charge of sending the address-claimed message, so you
> > > > > > > would have to decide how much to keep track of the request for address-
> > > > > > > claimed message thus adding more complexity to the code of the driver.
> > > > > >
> > > > > > Current kernel already tracks all claims on the bus and knows all registered
> > > > > > NAMEs. I do not see increased complicity in this case.
> > > > >
> > > > > The kernel tracks the claims but it does *not track* incoming requests
> > > > > for address-claimed message, it would have to and it would have to
> > > >
> > > > yes
> > > >
> > > > > allow the application to answer to it *within a defined time window*.
> > > >
> > > > yes.
> > > >
> > > > > But keep in mind that there are other cases when the 250 ms wait is wrong
> > > > > or it is not explicitly stated by the standard.
> > > >
> > > > If it is not stated in the standard how can we decide if it is wrong?
> > > And how can we decide if it is right? :)
> > >
> > > > And if strongly worded statements have no value just because it is
> > > > stated only one time, how proper standard should look like?
> > > See above.
> > >
> > > >
> > > > > > IMHO, only missing part i a user space interface. Some thing like "ip n"
> > > > > > will do.
> > > > > >
> > > > > > > Another solution is to let the driver send the address-claimed message
> > > > > > > waiting or without waiting 250 ms for successive messages depending on
> > > > > > > the case.
> > > > > >
> > > > > > You can send "address-claimed message" in any time you wont. Kernel will
> > > > > > just not resolve the NAME to address until 1. part of the spec will
> > > > > > apply. Do not forget, the NAME cache is used for local _and_ remote
> > > > > > names. You can trick out local system, not remote.
> > > > > >
> > > > > > Even if you implement "smart" logic in user space and will know better
> > > > > > then kernel, that this application is responding to RfAC. You will newer
> > > > > > know if address-claimed message of remote system is a response to RfAC.
> > > > > >
> > > > > > From this perspective, I do not know, how allowing the user space break
> > > > > > the rules will help to solve the problem?
> > > > >
> > > > > I think you did not understand this last proposal: since the driver is
> > > > > already implementing part of the standard, then it might as well send
> > > > > the address-claimed message when needed and wait 250 ms or not depending
> > > > > on the case.
> > > >
> > > > Let's try following test:
> > > > j1939acd -r 80 -c /tmp/1122334455667788.jacd 11223344556677 vcan0 &
> > > > while(true); do testj1939 -s8 vcan0:0x80 :0x90,0x12300; done
> > > >
> > > > And start candump with delta time stamps:
> > > > :~ candump -t d vcan0
> > > > (000.000000) vcan0 18EAFFFE [3] 00 EE 00
> > > > (000.002437) vcan0 19239080 [8] 01 23 45 67 89 AB CD EF <---- no 250ms delay
> > > > (000.011458) vcan0 19239080 [8] 01 23 45 67 89 AB CD EF
> > > > (000.011964) vcan0 19239080 [8] 01 23 45 67 89 AB CD EF
> > > > (000.011712) vcan0 19239080 [8] 01 23 45 67 89 AB CD EF
> > > > (000.012585) vcan0 19239080 [8] 01 23 45 67 89 AB CD EF
> > > > (000.012891) vcan0 19239080 [8] 01 23 45 67 89 AB CD EF
> > > > (000.012082) vcan0 19239080 [8] 01 23 45 67 89 AB CD EF
> > > > (000.012604) vcan0 19239080 [8] 01 23 45 67 89 AB CD EF
> > > > (000.012357) vcan0 19239080 [8] 01 23 45 67 89 AB CD EF
> > > > (000.012790) vcan0 19239080 [8] 01 23 45 67 89 AB CD EF
> > > > (000.012765) vcan0 19239080 [8] 01 23 45 67 89 AB CD EF
> > > > (000.012483) vcan0 19239080 [8] 01 23 45 67 89 AB CD EF
> > > > (000.012680) vcan0 19239080 [8] 01 23 45 67 89 AB CD EF
> > > > (000.012144) vcan0 19239080 [8] 01 23 45 67 89 AB CD EF
> > > > ... snip ...
> > > > (000.012592) vcan0 19239080 [8] 01 23 45 67 89 AB CD EF
> > > > (000.012515) vcan0 19239080 [8] 01 23 45 67 89 AB CD EF
> > > > (000.013183) vcan0 19239080 [8] 01 23 45 67 89 AB CD EF
> > > > (000.012653) vcan0 19239080 [8] 01 23 45 67 89 AB CD EF
> > > > (000.011886) vcan0 19239080 [8] 01 23 45 67 89 AB CD EF
> > > > (000.012836) vcan0 19239080 [8] 01 23 45 67 89 AB CD EF
> > > > (000.009494) vcan0 18EEFF80 [8] 77 66 55 44 33 22 11 00 <---- SA 0x80 address claimed
> > > > (000.003362) vcan0 19239080 [8] 01 23 45 67 89 AB CD EF <---- next packet from SA 0x80 3 usecs after previous. No 250ms delay.
> > > > (000.012351) vcan0 19239080 [8] 01 23 45 67 89 AB CD EF
> > > > (000.012983) vcan0 19239080 [8] 01 23 45 67 89 AB CD EF
> > > > (000.012602) vcan0 19239080 [8] 01 23 45 67 89 AB CD EF
> > > > (000.012594) vcan0 19239080 [8] 01 23 45 67 89 AB CD EF
> > > > (000.012348) vcan0 19239080 [8] 01 23 45 67 89 AB CD EF
> > > > (000.011922) vcan0 19239080 [8] 01 23 45 67 89 AB CD EF
> > > >
> > > > As you can see, the j1939 stack do not forcing application to use NAMEs and
> > > > do not preventing sending any message withing 250ms delay. The only thing
> > > > what has the 250 timer is NAME to address resolution which should be fixed in
> > > > respect of 4.5.2.d without breaking every thing else.
> > >
> > > Yes this is clear, this is working because the socket used by testj1939
> > > is not bound to any name.
> > >
> > > Just to clarify: are you suggesting to applications developer to use one
> > > socket (bound with the name) to manage the address-claim and another one
> > > (bound without the name) for other transmissions? If so, then why that
> > > code exists in the driver?
> > > Honestly I would consider this proposal really bad since this would
> > > allow to completely violate the standard. I really hope you agree with
> > > me about this.
> >
> > Hm... you are right.
> >
> > Please add to your patch code comments with standard snippets and
> > clarification why it should be so. Commit comment will be often
> > overseen.
> >
> > Regards,
> > Oleksij
>
> Would the following comment be acceptable? Isn't it too long?
>
> The ISO 11783-5 standard, in "4.5.2 - Address claim requirements",
> states:
> d) No CF shall begin, or resume, transmission on the network until 250
> ms after it has successfully claimed an address except when
> responding to a request for address-claimed.
> But "Figure 6" and "Figure 7" in "4.5.4.2 - Address-claim
> prioritization" show that the CF begin the transmission after 250 ms
> from the first AC (address-claimed) message even if it sends another AC
> message during that time window to resolve the address contention with
> another CF.
> As stated in "4.4.2.3 - Address-claimed message":
> In order to successfully claim an address, the CF sending an address
> claimed message shall not receive a contending claim from another CF
> for at least 250 ms.
> As stated in "4.4.3.2 - NAME management (NM) message":
> 1) A commanding CF can
> d) request that a CF with a specified NAME transmit the address-
> claimed message with its current NAME.
> 2) A target CF shall
> d) send an address-claimed message in response to a request for a
> matching NAME
> Taking the above arguments into account, the 250 ms wait is requested
> only during network initialization.
> Do not restart the timer on AC message if both the NAME and the address
> match and therefore if the address has already been claimed (timer has
> expired) or the AC message has been sent to resolve the contention with
> another CF (timer is still running).

Sounds good.

Regards,
Oleksij
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |

\
 
 \ /
  Last update: 2022-11-24 06:17    [W:0.193 / U:0.432 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site