lkml.org 
[lkml]   [2022]   [Nov]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH AUTOSEL 5.10 05/22] serial: 8250: 8250_omap: Avoid RS485 RTS glitch on ->set_termios()
Date
From: Lukas Wunner <lukas@wunner.de>

[ Upstream commit 038ee49fef18710bedd38b531d173ccd746b2d8d ]

RS485-enabled UART ports on TI Sitara SoCs with active-low polarity
exhibit a Transmit Enable glitch on ->set_termios():

omap8250_restore_regs(), which is called from omap_8250_set_termios(),
sets the TCRTLR bit in the MCR register and clears all other bits,
including RTS. If RTS uses active-low polarity, it is now asserted
for no reason.

The TCRTLR bit is subsequently cleared by writing up->mcr to the MCR
register. That variable is always zero, so the RTS bit is still cleared
(incorrectly so if RTS is active-high).

(up->mcr is not, as one might think, a cache of the MCR register's
current value. Rather, it only caches a single bit of that register,
the AFE bit. And it only does so if the UART supports the AFE bit,
which OMAP does not. For details see serial8250_do_set_termios() and
serial8250_do_set_mctrl().)

Finally at the end of omap8250_restore_regs(), the MCR register is
restored (and RTS deasserted) by a call to up->port.ops->set_mctrl()
(which equals serial8250_set_mctrl()) and serial8250_em485_stop_tx().

So there's an RTS glitch between setting TCRTLR and calling
serial8250_em485_stop_tx(). Avoid by using a read-modify-write
when setting TCRTLR.

While at it, drop a redundant initialization of up->mcr. As explained
above, the variable isn't used by the driver and it is already
initialized to zero because it is part of the static struct
serial8250_ports[] declared in 8250_core.c. (Static structs are
initialized to zero per section 6.7.8 nr. 10 of the C99 standard.)

Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Su Bao Cheng <baocheng.su@siemens.com>
Tested-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/6554b0241a2c7fd50f32576fdbafed96709e11e8.1664278942.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/tty/serial/8250/8250_omap.c | 7 ++++---
1 file changed, 4 insertions(+), 3 deletions(-)

diff --git a/drivers/tty/serial/8250/8250_omap.c b/drivers/tty/serial/8250/8250_omap.c
index f3744ac805ec..61cf7b3169c2 100644
--- a/drivers/tty/serial/8250/8250_omap.c
+++ b/drivers/tty/serial/8250/8250_omap.c
@@ -292,6 +292,7 @@ static void omap8250_restore_regs(struct uart_8250_port *up)
{
struct omap8250_priv *priv = up->port.private_data;
struct uart_8250_dma *dma = up->dma;
+ u8 mcr = serial8250_in_MCR(up);

if (dma && dma->tx_running) {
/*
@@ -308,7 +309,7 @@ static void omap8250_restore_regs(struct uart_8250_port *up)
serial_out(up, UART_EFR, UART_EFR_ECB);

serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
- serial8250_out_MCR(up, UART_MCR_TCRTLR);
+ serial8250_out_MCR(up, mcr | UART_MCR_TCRTLR);
serial_out(up, UART_FCR, up->fcr);

omap8250_update_scr(up, priv);
@@ -324,7 +325,8 @@ static void omap8250_restore_regs(struct uart_8250_port *up)
serial_out(up, UART_LCR, 0);

/* drop TCR + TLR access, we setup XON/XOFF later */
- serial8250_out_MCR(up, up->mcr);
+ serial8250_out_MCR(up, mcr);
+
serial_out(up, UART_IER, up->ier);

serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
@@ -683,7 +685,6 @@ static int omap_8250_startup(struct uart_port *port)

pm_runtime_get_sync(port->dev);

- up->mcr = 0;
serial_out(up, UART_FCR, UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);

serial_out(up, UART_LCR, UART_LCR_WLEN8);
--
2.35.1
\
 
 \ /
  Last update: 2022-11-23 13:51    [W:0.076 / U:0.384 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site