lkml.org 
[lkml]   [2022]   [Nov]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH V2 6/6] Documentation/osnoise: Add osnoise/options documentation
Date
Add the documentation about the osnoise/options file, the options,
and some additional explanation about the OSNOISE_WORKLOAD option.

Cc: Daniel Bristot de Oliveira <bristot@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Daniel Bristot de Oliveira <bristot@kernel.org>
---
Documentation/trace/osnoise-tracer.rst | 32 ++++++++++++++++++++++++--
1 file changed, 30 insertions(+), 2 deletions(-)

diff --git a/Documentation/trace/osnoise-tracer.rst b/Documentation/trace/osnoise-tracer.rst
index 963def9f97c6..618bcdc90bb6 100644
--- a/Documentation/trace/osnoise-tracer.rst
+++ b/Documentation/trace/osnoise-tracer.rst
@@ -92,8 +92,8 @@ Note that the example above shows a high number of HW noise samples.
The reason being is that this sample was taken on a virtual machine,
and the host interference is detected as a hardware interference.

-Tracer options
----------------------
+Tracer Configuration
+--------------------

The tracer has a set of options inside the osnoise directory, they are:

@@ -109,6 +109,27 @@ The tracer has a set of options inside the osnoise directory, they are:
- tracing_threshold: the minimum delta between two time() reads to be
considered as noise, in us. When set to 0, the default value will
be used, which is currently 5 us.
+ - osnoise/options: a set of on/off options that can be enabled by
+ writing the option name to the file or disabled by writing the option
+ name preceded with the 'NO_' prefix. For example, writing
+ NO_OSNOISE_WORKLOAD disables the OSNOISE_WORKLOAD option. The
+ special DEAFAULTS option resets all options to the default value.
+
+Tracer Options
+--------------
+
+The osnoise/options file exposes a set of on/off configuration options for
+the osnoise tracer. These options are:
+
+ - DEFAULTS: reset the options to the default value.
+ - OSNOISE_WORKLOAD: do not dispatch osnoise workload (see dedicated
+ section below).
+ - PANIC_ON_STOP: call panic() if the tracer stops. This option serves to
+ capture a vmcore.
+ - OSNOISE_PREEMPT_DISABLE: disable preemption while running the osnoise
+ workload, allowing only IRQ-related and hardware-related noise.
+ - OSNOISE_IRQ_DISABLE: disable IRQs while running the osnoise workload,
+ allowing only NMIs and hardware-related noise, like hwlat tracer.

Additional Tracing
------------------
@@ -150,3 +171,10 @@ tracepoints is smaller than eight us reported in the sample_threshold.
The reason roots in the overhead of the entry and exit code that happens
before and after any interference execution. This justifies the dual
approach: measuring thread and tracing.
+
+Running osnoise tracer without workload
+---------------------------------------
+
+By enabling the osnoise tracer with the NO_OSNOISE_WORKLOAD option set,
+the osnoise: tracepoints serves to measure the execution time of
+any type of Linux task, free from the interference of other tasks.
--
2.32.0
\
 
 \ /
  Last update: 2022-11-23 18:08    [W:0.067 / U:0.776 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site