lkml.org 
[lkml]   [2022]   [Nov]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH net-next 6/6] net: mvpp2: Consider NVMEM cells as possible MAC address source
Hi Marcin,

mw@semihalf.com wrote on Mon, 21 Nov 2022 15:46:44 +0100:

> pon., 21 lis 2022 o 10:29 Miquel Raynal <miquel.raynal@bootlin.com> napisał(a):
> >
> > Hi Marcin,
> >
> > mw@semihalf.com wrote on Sat, 19 Nov 2022 09:18:34 +0100:
> >
> > > Hi Miquel,
> > >
> > >
> > > czw., 17 lis 2022 o 22:56 Miquel Raynal <miquel.raynal@bootlin.com> napisał(a):
> > > >
> > > > The ONIE standard describes the organization of tlv (type-length-value)
> > > > arrays commonly stored within NVMEM devices on common networking
> > > > hardware.
> > > >
> > > > Several drivers already make use of NVMEM cells for purposes like
> > > > retrieving a default MAC address provided by the manufacturer.
> > > >
> > > > What made ONIE tables unusable so far was the fact that the information
> > > > where "dynamically" located within the table depending on the
> > > > manufacturer wishes, while Linux NVMEM support only allowed statically
> > > > defined NVMEM cells. Fortunately, this limitation was eventually tackled
> > > > with the introduction of discoverable cells through the use of NVMEM
> > > > layouts, making it possible to extract and consistently use the content
> > > > of tables like ONIE's tlv arrays.
> > > >
> > > > Parsing this table at runtime in order to get various information is now
> > > > possible. So, because many Marvell networking switches already follow
> > > > this standard, let's consider using NVMEM cells as a new valid source of
> > > > information when looking for a base MAC address, which is one of the
> > > > primary uses of these new fields. Indeed, manufacturers following the
> > > > ONIE standard are encouraged to provide a default MAC address there, so
> > > > let's eventually use it if no other MAC address has been found using the
> > > > existing methods.
> > > >
> > > > Link: https://opencomputeproject.github.io/onie/design-spec/hw_requirements.html
> > >
> > > Thanks for the patch. Did you manage to test in on a real HW? I am curious about
> >
> > Yes, I have a Replica switch on which the commercial ports use the
> > replica PCI IP while the config "OOB" port is running with mvpp2:
> > [ 16.737759] mvpp2 f2000000.ethernet eth52: Using nvmem cell mac address 18:be:92:13:9a:00
> >
>
> Nice. Do you have a DT snippet that can possibly be shared? I'd like
> to recreate this locally and eventually leverage EDK2 firmware to
> expose that.

Yes of course, the DT is public on Sartura's Github, but here is the
exact file I used showing the diff cleaning the Armada 7040 TN48M DT
eeprom description and its use as an nvmem-cell provider):
https://github.com/miquelraynal/linux/commit/230ee68728799454e2f07f61792e11724e731d6d

>
> > > > Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> > > > ---
> > > > drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 6 ++++++
> > > > 1 file changed, 6 insertions(+)
> > > >
> > > > diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
> > > > index eb0fb8128096..7c8c323f4411 100644
> > > > --- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
> > > > +++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
> > > > @@ -6104,6 +6104,12 @@ static void mvpp2_port_copy_mac_addr(struct net_device *dev, struct mvpp2 *priv,
> > > > }
> > > > }
> > > >
> > > > + if (!of_get_mac_address(to_of_node(fwnode), hw_mac_addr)) {
> > >
> > > Unfortunately, nvmem cells seem to be not supported with ACPI yet, so
> > > we cannot extend fwnode_get_mac_address - I think it should be,
> > > however, an end solution.
> >
> > Agreed.
> >
> > > As of now, I'd prefer to use of_get_mac_addr_nvmem directly, to avoid
> > > parsing the DT again (after fwnode_get_mac_address) and relying
> > > implicitly on falling back to nvmem stuff (currently, without any
> > > comment it is not obvious).
> >
> > I did not do that in the first place because of_get_mac_addr_nvmem()
> > was not exported, but I agree it would be the cleanest (and quickest)
> > approach, so I'll attempt to export the function first, and then use it
> > directly from the driver.
> >
>
> That would be great, thank you. Please add one-comment in the
> mvpp2_main.c, that this is valid for now only in DT world.

Ack.

Thanks,
Miquèl

\
 
 \ /
  Last update: 2022-11-22 18:56    [W:0.061 / U:0.316 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site