lkml.org 
[lkml]   [2022]   [Nov]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Date
Subject[PATCH v2 2/2] drm/tiny: ili9486: Do not assume 8-bit only SPI controllers
The pixel data for the ILI9486 is always 16-bits wide and it must be
sent over the SPI bus. When the controller is only able to deal with
8-bit transfers, this 16-bits data needs to be swapped before the
sending to account for the big endian bus, this is on the contrary not
needed when the SPI controller already supports 16-bits transfers.

The decision about swapping the pixel data or not is taken in the MIPI
DBI code by probing the controller capabilities: if the controller only
suppors 8-bit transfers the data is swapped, otherwise it is not.

This swapping/non-swapping is relying on the assumption that when the
controller does support 16-bit transactions then the data is sent
unswapped in 16-bits-per-word over SPI.

The problem with the ILI9486 driver is that it is forcing 8-bit
transactions also for controllers supporting 16-bits, violating the
assumption and corrupting the pixel data.

Align the driver to what is done in the MIPI DBI code by adjusting the
tranfer size to the maximum allowed by the SPI controller.

Signed-off-by: Carlo Caione <ccaione@baylibre.com>
---
drivers/gpu/drm/tiny/ili9486.c | 13 +++++++++----
1 file changed, 9 insertions(+), 4 deletions(-)

diff --git a/drivers/gpu/drm/tiny/ili9486.c b/drivers/gpu/drm/tiny/ili9486.c
index bd37dfe8dd05..4d80a413338f 100644
--- a/drivers/gpu/drm/tiny/ili9486.c
+++ b/drivers/gpu/drm/tiny/ili9486.c
@@ -43,6 +43,7 @@ static int waveshare_command(struct mipi_dbi *mipi, u8 *cmd, u8 *par,
size_t num)
{
struct spi_device *spi = mipi->spi;
+ unsigned int bpw = 8;
void *data = par;
u32 speed_hz;
int i, ret;
@@ -56,8 +57,6 @@ static int waveshare_command(struct mipi_dbi *mipi, u8 *cmd, u8 *par,
* The displays are Raspberry Pi HATs and connected to the 8-bit only
* SPI controller, so 16-bit command and parameters need byte swapping
* before being transferred as 8-bit on the big endian SPI bus.
- * Pixel data bytes have already been swapped before this function is
- * called.
*/
buf[0] = cpu_to_be16(*cmd);
gpiod_set_value_cansleep(mipi->dc, 0);
@@ -71,12 +70,18 @@ static int waveshare_command(struct mipi_dbi *mipi, u8 *cmd, u8 *par,
for (i = 0; i < num; i++)
buf[i] = cpu_to_be16(par[i]);
num *= 2;
- speed_hz = mipi_dbi_spi_cmd_max_speed(spi, num);
data = buf;
}

+ /*
+ * Check whether pixel data bytes needs to be swapped or not
+ */
+ if (*cmd == MIPI_DCS_WRITE_MEMORY_START && !mipi->swap_bytes)
+ bpw = 16;
+
gpiod_set_value_cansleep(mipi->dc, 1);
- ret = mipi_dbi_spi_transfer(spi, speed_hz, 8, data, num);
+ speed_hz = mipi_dbi_spi_cmd_max_speed(spi, num);
+ ret = mipi_dbi_spi_transfer(spi, speed_hz, bpw, data, num);
free:
kfree(buf);

--
b4 0.10.1

\
 
 \ /
  Last update: 2022-11-21 10:43    [W:0.217 / U:0.136 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site