lkml.org 
[lkml]   [2022]   [Nov]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v2 2/5] dt-bindings: pinctrl: Add StarFive JH7110 sys pinctrl
From
On 18/11/2022 02:11, Hal Feng wrote:
> From: Jianlong Huang <jianlong.huang@starfivetech.com>
>
> Add pinctrl bindings for StarFive JH7110 SoC sys pinctrl controller.
>
> Signed-off-by: Jianlong Huang <jianlong.huang@starfivetech.com>
> Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
> ---
> .../pinctrl/starfive,jh7110-sys-pinctrl.yaml | 165 ++++++++++++++++++
> 1 file changed, 165 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml
> new file mode 100644
> index 000000000000..79623f884a9c
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml
> @@ -0,0 +1,165 @@
> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pinctrl/starfive,jh7110-sys-pinctrl.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: StarFive JH7110 Sys Pin Controller
> +
> +description: |
> + Bindings for the JH7110 RISC-V SoC from StarFive Technology Ltd.
> +
> + Out of the SoC's many pins only the ones named PAD_GPIO0 to PAD_GPIO63
> + can be multiplexed and have configurable bias, drive strength,
> + schmitt trigger etc.
> + Some peripherals have their I/O go through the 64 "GPIOs". This also
> + includes a number of other UARTs, I2Cs, SPIs, PWMs etc.
> + All these peripherals are connected to all 64 GPIOs such that
> + any GPIO can be set up to be controlled by any of the peripherals.
> +
> +maintainers:
> + - Jianlong Huang <jianlong.huang@starfivetech.com>
> +
> +properties:
> + compatible:
> + const: starfive,jh7110-sys-pinctrl
> +
> + reg:
> + maxItems: 1
> +
> + reg-names:
> + items:
> + - const: control

Why reg-names for one entry? Perhaps just drop it.

> +
> + clocks:
> + maxItems: 1
> +
> + resets:
> + maxItems: 1
> +
> + gpio-controller: true
> +
> + "#gpio-cells":
> + const: 2
> +
> + interrupts:
> + maxItems: 1
> + description: The GPIO parent interrupt.

Drop description, it's obvious.

> +
> + interrupt-controller: true
> +
> + "#interrupt-cells":
> + const: 2
> +
> +required:
> + - compatible
> + - reg
> + - reg-names
> + - clocks
> + - gpio-controller
> + - "#gpio-cells"
> + - interrupts
> + - interrupt-controller
> + - "#interrupt-cells"
> +
> +patternProperties:
> + '-[0-9]+$':

Keep consistent quotes, either ' or "

How do you differentiate hogs? The pattern is a bit unspecific.

> + type: object
> + patternProperties:
> + '-pins$':
> + type: object
> + description: |
> + A pinctrl node should contain at least one subnode representing the
> + pinctrl groups available on the machine. Each subnode will list the
> + pins it needs, and how they should be configured, with regard to
> + muxer configuration, system signal configuration, pin groups for
> + vin/vout module, pin voltage, mux functions for output, mux functions
> + for output enable, mux functions for input.
> +
> + properties:
> + pinmux:
> + description: |
> + The list of GPIOs and their mux settings that properties in the
> + node apply to. This should be set using the GPIOMUX macro.
> + $ref: "/schemas/pinctrl/pinmux-node.yaml#/properties/pinmux"

Drop quotes.

> +
> + bias-disable: true
> +
> + bias-pull-up:
> + type: boolean
> +
> + bias-pull-down:
> + type: boolean
> +
> + drive-strength:
> + enum: [ 2, 4, 8, 12 ]
> +
> + input-enable: true
> +
> + input-disable: true
> +
> + input-schmitt-enable: true
> +
> + input-schmitt-disable: true
> +
> + slew-rate:
> + maximum: 1
> +
> + additionalProperties: false
> +
> + additionalProperties: false
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/clock/starfive-jh7110.h>
> + #include <dt-bindings/reset/starfive-jh7110.h>
> + #include <dt-bindings/pinctrl/pinctrl-starfive-jh7110.h>
> +
> + soc {

Use 4 spaces for example indentation.

> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + gpio: gpio@13040000 {
> + compatible = "starfive,jh7110-sys-pinctrl";
> + reg = <0x0 0x13040000 0x0 0x10000>;
> + reg-names = "control";
> + clocks = <&syscrg_clk JH7110_SYSCLK_IOMUX>;
> + resets = <&syscrg_rst JH7110_SYSRST_IOMUX>;
> + interrupts = <86>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + #gpio-cells = <2>;
> + gpio-controller;
> + status = "okay";

No status in examples.

> +
> + uart0_pins: uart0-0 {
> + tx-pins {
> + pinmux = <GPIOMUX(5, GPOUT_SYS_UART0_TX, GPOEN_ENABLE, GPI_NONE)>;
> + bias-disable;
> + drive-strength = <12>;
> + input-disable;
> + input-schmitt-disable;
> + slew-rate = <0>;
> + };
> +
> + rx-pins {
> + pinmux = <GPIOMUX(6, GPOUT_LOW, GPOEN_DISABLE, GPI_SYS_UART0_RX)>;
> + bias-pull-up;
> + drive-strength = <2>;
> + input-enable;
> + input-schmitt-enable;
> + slew-rate = <0>;
> + };
> + };
> + };
> +
> + uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_pins>;
> + status = "okay";

Drop this node, useless.

> + };
> + };
> +
> +...

Best regards,
Krzysztof

\
 
 \ /
  Last update: 2022-11-21 09:44    [W:0.140 / U:1.004 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site