lkml.org 
[lkml]   [2022]   [Nov]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v5] PCI/ACPI: PCI/ACPI: Validate devices with power resources support D3
On Mon, Nov 21, 2022 at 03:33:00PM +0100, Rafael J. Wysocki wrote:
> On Friday, November 18, 2022 10:13:39 PM CET Rafael J. Wysocki wrote:
> > On Fri, Nov 18, 2022 at 9:23 PM Bjorn Helgaas <helgaas@kernel.org> wrote:
> > >
> > > Hi Rafael,
> > >
> > > Sorry, I'm still confused (my perpetual state :)).
> >
> > No worries, doing my best to address that.
> >
> > > On Fri, Nov 18, 2022 at 02:16:17PM +0100, Rafael J. Wysocki wrote:
> > > > On Thu, Nov 17, 2022 at 11:16 PM Bjorn Helgaas <helgaas@kernel.org> wrote:
> > > > > On Thu, Nov 17, 2022 at 06:01:26PM +0100, Rafael J. Wysocki wrote:
> > > > > > On Thu, Nov 17, 2022 at 12:28 AM Bjorn Helgaas <helgaas@kernel.org> wrote:
> > > > > > > On Wed, Nov 16, 2022 at 01:00:36PM +0100, Rafael J. Wysocki wrote:
> > > > > > > > On Wed, Nov 16, 2022 at 1:37 AM Bjorn Helgaas <helgaas@kernel.org> wrote:
> > > > > > > > > On Mon, Nov 14, 2022 at 04:33:52PM +0100, Rafael J. Wysocki wrote:
> > > > > > > > > > On Fri, Nov 11, 2022 at 10:42 PM Bjorn Helgaas <helgaas@kernel.org> wrote:
> > > > > > > > > > >
> > > > > > > > > > > On Fri, Nov 11, 2022 at 12:58:28PM -0600, Limonciello, Mario wrote:
> > > > > > > > > > > > On 11/11/2022 11:41, Bjorn Helgaas wrote:
> > > > > > > > > > > > > On Mon, Oct 31, 2022 at 05:33:55PM -0500, Mario Limonciello wrote:
> > > > > > > > > > > > > > Firmware typically advertises that ACPI devices that represent PCIe
> > > > > > > > > > > > > > devices can support D3 by a combination of the value returned by
> > > > > > > > > > > > > > _S0W as well as the HotPlugSupportInD3 _DSD [1].
> > > > > > > > > > > > > >
> > > > > > > > > > > > > > `acpi_pci_bridge_d3` looks for this combination but also contains
> > > > > > > > > > > > > > an assumption that if an ACPI device contains power resources the PCIe
> > > > > > > > > > > > > > device it's associated with can support D3. This was introduced
> > > > > > > > > > > > > > from commit c6e331312ebf ("PCI/ACPI: Whitelist hotplug ports for
> > > > > > > > > > > > > > D3 if power managed by ACPI").
> > > > > > > > > > > > > >
> > > > > > > > > > > > > > Some firmware configurations for "AMD Pink Sardine" do not support
> > > > > > > > > > > > > > wake from D3 in _S0W for the ACPI device representing the PCIe root
> > > > > > > > > > > > > > port used for tunneling. The PCIe device will still be opted into
> > > > > > > > > > > > > > runtime PM in the kernel [2] because of the logic within
> > > > > > > > > > > > > > `acpi_pci_bridge_d3`. This currently happens because the ACPI
> > > > > > > > > > > > > > device contains power resources.
> > > > > > > > > > >
> > > > > > > > > > > Wait. Is this as simple as just recognizing that:
> > > > > > > > > > >
> > > > > > > > > > > _PS0 means the OS has a knob to put the device in D0, but it doesn't
> > > > > > > > > > > mean the device can wake itself from a low-power state. The OS has
> > > > > > > > > > > to use _S0W to learn the device's ability to wake itself.
> > > > > > > > > >
> > > > > > > > > > It is.
> > > > > > > > >
> > > > > > > > > Now I'm confused again about what "HotPlugSupportInD3" means. The MS
> > > > > > > > > web page [1] says it identifies Root Ports capable of handling hot
> > > > > > > > > plug events while in D3. That sounds kind of related to _S0W: If _S0W
> > > > > > > > > says "I can wake myself from D3hot and D3cold", how is that different
> > > > > > > > > from "I can handle hotplug events in D3"?
> > > > > > > >
> > > > > > > > For native PME/hot-plug signaling there is no difference. This is the
> > > > > > > > same interrupt by the spec after all IIRC.
> > > > > > > >
> > > > > > > > For GPE-based signaling, though, there is a difference, because GPEs
> > > > > > > > can only be used directly for wake signaling (this is related to
> > > > > > > > _PRW). In particular, the only provision in the ACPI spec for device
> > > > > > > > hot-add are the Bus Check and Device Check notification values (0 and
> > > > > > > > 1) which require AML to run and evaluate Notify() on specific AML
> > > > > > > > objects.
> > > > > > > >
> > > > > > > > Hence, there is no spec-defined way to tell the OS that "something can
> > > > > > > > be hot-added under this device while in D3 and you will get notified
> > > > > > > > about that".
> > > > > > >
> > > > > > > So I guess acpi_pci_bridge_d3() looks for:
> > > > > > >
> > > > > > > - "wake signaling while in D3" (_S0W) and
> > > > > > > - "notification of hotplug while in D3" ("HotPlugSupportInD3")
> > > > > > >
> > > > > > > For Root Ports with both those abilities (or bridges below such Root
> > > > > > > Ports), we allow D3, and this patch doesn't change that.
> > > > > > >
> > > > > > > What this patch *does* change is that all bridges with _PS0 or _PR0
> > > > > > > previously could use D3, but now will only be able to use D3 if they
> > > > > > > are also (or are below) a Root Port that can signal wakeup
> > > > > > > (wakeup.flags.valid) and can wakeup from D3hot or D3cold (_S0W).
> > > > > > >
> > > > > > > And this fixes the Pink Sardine because it has Root Ports that do
> > > > > > > Thunderbolt tunneling, and they have _PS0 or _PR0 but their _S0W says
> > > > > > > they cannot wake from D3. Previously we put those in D3, but they
> > > > > > > couldn't wake up. Now we won't put them in D3.
> > > > > > >
> > > > > > > I guess there's a possibility that this could break or cause higher
> > > > > > > power consumption on systems that were fixed by c6e331312ebf
> > > > > > > ("PCI/ACPI: Whitelist hotplug ports for D3 if power managed by ACPI").
> > > > > > > I don't know enough about that scenario. Maybe Lukas will chime in.
> > > > > >
> > > > > > Well, it is possible that some of these systems will be affected.
> > > > > >
> > > > > > One of such cases is when the port in question has _S0W which says
> > > > > > that wakeup from D3 is not supported. In that case I think the kernel
> > > > > > should honor the _S0W input, because there may be a good reason known
> > > > > > to the platform integrator for it.
> > > > > >
> > > > > > The other case is when wakeup.flags.valid is unset for the port's ACPI
> > > > > > companion which means that the port cannot signal wakeup through
> > > > > > ACPI-related means at all and this may be problematic, especially in
> > > > > > the system-wide suspend case in which the wakeup capability is not too
> > > > > > relevant unless there is a system wakeup device under the port.
> > > > > >
> > > > > > I don't think that the adev->wakeup.flags.valid check has any bearing
> > > > > > on the _S0W check - if there is _S0W and it says "no wakeup from D3",
> > > > > > it should still be taken into account - so that check can be moved
> > > > > > past the _S0W check.
> > > > >
> > > > > So if _S0W says it can wake from D3, but wakeup.flags is not valid,
> > > > > it's still OK to use D3?
> > > >
> > > > No, it isn't, as per the code today and I don't think that this
> > > > particular part should be changed now.
> > >
> > > But the current upstream code checks acpi_pci_power_manageable(dev)
> > > first, so if "dev" has _PR0 or _PS0, we'll use D3 even if _S0W says it
> > > can wake from D3 and wakeup.flags is not valid.
> >
> > Yes, the current code will return 'true' if _PR0 or _PS0 is present
> > for dev regardless of anything else.
> >
> > The proposed change is to make that conditional on whether or not _S0W
> > for the root port says that wakeup from D3 is supported (or it is not
> > present or unusable).
> >
> > I see that I've missed one point now which is when the root port
> > doesn't have an ACPI companion, in which case we should go straight
> > for the "dev is power manageable" check.
>
> Moreover, it is possible that the bridge passed to acpi_pci_bridge_d3() has its
> own _S0W or a wakeup GPE if it is power-manageable via ACPI. In those cases
> it is not necessary to ask the Root Port's _S0W about wakeup from D3, so overall
> I would go for the patch like the below (not really tested).
>
> This works in the same way as the current code (unless I have missed anything)
> except for the case when the "target" bridge is power-manageable via ACPI, but
> it cannot signal wakeup via ACPI and has no _S0W. In that case it will consult
> the upstream Root Port's _S0W to check whether or not wakeup from D3 is
> supported.
>
> [Note that if dev_has_acpi_pm is 'true', it is kind of pointless to look for the
> "HotPlugSupportInD3" property of the Root Port, because the function is going to
> return 'true' regardless, but I'm not sure if adding an extra if () for handling
> this particular case is worth the hassle.]

I think this has a lot of potential. I haven't tried it, but I wonder
if splitting out the Root Port-specific parts to a separate function
would be helpful, if only to make it more obvious that there may be
two different devices involved.

If there are two devices ("dev" is a bridge below a Root Port), I
guess support in the Root Port is not necessarily required? E.g.,
could "dev" assert a wakeup GPE that's not routed through the Root
Port? If Root Port support *is* required, maybe it would read more
clearly to test that first, before looking at the downstream device.

> ---
> drivers/pci/pci-acpi.c | 32 +++++++++++++++++++++++++-------
> 1 file changed, 25 insertions(+), 7 deletions(-)
>
> Index: linux-pm/drivers/pci/pci-acpi.c
> ===================================================================
> --- linux-pm.orig/drivers/pci/pci-acpi.c
> +++ linux-pm/drivers/pci/pci-acpi.c
> @@ -975,6 +975,7 @@ bool acpi_pci_power_manageable(struct pc
>
> bool acpi_pci_bridge_d3(struct pci_dev *dev)
> {
> + bool dev_has_acpi_pm = false;
> struct pci_dev *rpdev;
> struct acpi_device *adev;
> acpi_status status;
> @@ -984,17 +985,34 @@ bool acpi_pci_bridge_d3(struct pci_dev *
> if (acpi_pci_disabled || !dev->is_hotplug_bridge)
> return false;
>
> - /* Assume D3 support if the bridge is power-manageable by ACPI. */
> - if (acpi_pci_power_manageable(dev))
> - return true;
> + adev = ACPI_COMPANION(&dev->dev);
> + if (adev && acpi_device_power_manageable(adev)) {
> + /*
> + * Let the bridge go into D3 if it can signal wakeup from these
> + * states (i.e. it has _S0W which says so or it can signal
> + * wakeup via ACPI).
> + */
> + status = acpi_evaluate_integer(adev->handle, "_S0W", NULL, &state);
> + if (ACPI_SUCCESS(status)) {
> + if (state >= ACPI_STATE_D3_HOT)
> + return true;
> + } else if (adev->wakeup.flags.valid) {
> + return true;
> + }
> + /*
> + * If the bridge is power-manageable by ACPI, let it go into D3
> + * by default.
> + */
> + dev_has_acpi_pm = true;
> + }
>
> rpdev = pcie_find_root_port(dev);
> if (!rpdev)
> - return false;
> + return dev_has_acpi_pm;
>
> adev = ACPI_COMPANION(&rpdev->dev);
> if (!adev)
> - return false;
> + return dev_has_acpi_pm;
>
> /*
> * If the Root Port cannot signal wakeup signals at all, i.e., it
> @@ -1002,7 +1020,7 @@ bool acpi_pci_bridge_d3(struct pci_dev *
> * events from low-power states including D3hot and D3cold.
> */
> if (!adev->wakeup.flags.valid)
> - return false;
> + return dev_has_acpi_pm;
>
> /*
> * If the Root Port cannot wake itself from D3hot or D3cold, we
> @@ -1023,7 +1041,7 @@ bool acpi_pci_bridge_d3(struct pci_dev *
> obj->integer.value == 1)
> return true;
>
> - return false;
> + return dev_has_acpi_pm;
> }
>
> int acpi_pci_set_power_state(struct pci_dev *dev, pci_power_t state)
>
>
>

\
 
 \ /
  Last update: 2022-11-21 23:18    [W:0.098 / U:0.044 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site