lkml.org 
[lkml]   [2022]   [Nov]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v2] clk: qcom: gdsc: Remove direct runtime PM calls
Hi,

On Wed, Nov 2, 2022 at 10:07 AM Stephen Boyd <swboyd@chromium.org> wrote:
>
> We shouldn't be calling runtime PM APIs from within the genpd
> enable/disable path for a couple reasons.
>
> First, this causes an AA lockdep splat because genpd can call into genpd
> code again while holding the genpd lock.
>
> WARNING: possible recursive locking detected
> 5.19.0-rc2-lockdep+ #7 Not tainted
> --------------------------------------------
> kworker/2:1/49 is trying to acquire lock:
> ffffffeea0370788 (&genpd->mlock){+.+.}-{3:3}, at: genpd_lock_mtx+0x24/0x30
>
> but task is already holding lock:
> ffffffeea03710a8 (&genpd->mlock){+.+.}-{3:3}, at: genpd_lock_mtx+0x24/0x30
>
> other info that might help us debug this:
> Possible unsafe locking scenario:
>
> CPU0
> ----
> lock(&genpd->mlock);
> lock(&genpd->mlock);
>
> *** DEADLOCK ***
>
> May be due to missing lock nesting notation
>
> 3 locks held by kworker/2:1/49:
> #0: 74ffff80811a5748 ((wq_completion)pm){+.+.}-{0:0}, at: process_one_work+0x320/0x5fc
> #1: ffffffc008537cf8 ((work_completion)(&genpd->power_off_work)){+.+.}-{0:0}, at: process_one_work+0x354/0x5fc
> #2: ffffffeea03710a8 (&genpd->mlock){+.+.}-{3:3}, at: genpd_lock_mtx+0x24/0x30
>
> stack backtrace:
> CPU: 2 PID: 49 Comm: kworker/2:1 Not tainted 5.19.0-rc2-lockdep+ #7
> Hardware name: Google Lazor (rev3 - 8) with KB Backlight (DT)
> Workqueue: pm genpd_power_off_work_fn
> Call trace:
> dump_backtrace+0x1a0/0x200
> show_stack+0x24/0x30
> dump_stack_lvl+0x7c/0xa0
> dump_stack+0x18/0x44
> __lock_acquire+0xb38/0x3634
> lock_acquire+0x180/0x2d4
> __mutex_lock_common+0x118/0xe30
> mutex_lock_nested+0x70/0x7c
> genpd_lock_mtx+0x24/0x30
> genpd_runtime_suspend+0x2f0/0x414
> __rpm_callback+0xdc/0x1b8
> rpm_callback+0x4c/0xcc
> rpm_suspend+0x21c/0x5f0
> rpm_idle+0x17c/0x1e0
> __pm_runtime_idle+0x78/0xcc
> gdsc_disable+0x24c/0x26c
> _genpd_power_off+0xd4/0x1c4
> genpd_power_off+0x2d8/0x41c
> genpd_power_off_work_fn+0x60/0x94
> process_one_work+0x398/0x5fc
> worker_thread+0x42c/0x6c4
> kthread+0x194/0x1b4
> ret_from_fork+0x10/0x20
>
> Second, this confuses runtime PM on CoachZ for the camera devices by
> causing the camera clock controller's runtime PM usage_count to go
> negative after resuming from suspend. This is because runtime PM is
> being used on the clock controller while runtime PM is disabled for the
> device.
>
> The reason for the negative count is because a GDSC is represented as a
> genpd and each genpd that is attached to a device is resumed during the
> noirq phase of system wide suspend/resume (see the noirq suspend ops
> assignment in pm_genpd_init() for more details). The camera GDSCs are
> attached to camera devices with the 'power-domains' property in DT.
> Every device has runtime PM disabled in the late system suspend phase
> via __device_suspend_late(). Runtime PM is not usable until runtime PM
> is enabled in device_resume_early(). The noirq phases run after the
> 'late' and before the 'early' phase of suspend/resume. When the genpds
> are resumed in genpd_resume_noirq(), we call down into gdsc_enable()
> that calls pm_runtime_resume_and_get() and that returns -EACCES to
> indicate failure to resume because runtime PM is disabled for all
> devices.
>
> Upon closer inspection, calling runtime PM APIs like this in the GDSC
> driver doesn't make sense. It was intended to make sure the GDSC for the
> clock controller providing other GDSCs was enabled, specifically the
> MMCX GDSC for the display clk controller on SM8250 (sm8250-dispcc), so
> that GDSC register accesses succeeded. That will already happen because
> we make the 'dev->pm_domain' a parent domain of each GDSC we register in
> gdsc_register() via pm_genpd_add_subdomain(). When any of these GDSCs
> are accessed, we'll enable the parent domain (in this specific case
> MMCX).
>
> We also remove any getting of runtime PM during registration, because
> when a genpd is registered it increments the count on the parent if the
> genpd itself is already enabled. And finally, the runtime PM state of
> the clk controller registering the GDSC shouldn't matter to the
> subdomain setup. Therefore we always assign 'dev' unconditionally so
> when GDSCs are removed we properly unlink the GDSC from the clk
> controller's pm_domain.
>
> Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> Cc: Johan Hovold <johan+linaro@kernel.org>
> Cc: Ulf Hansson <ulf.hansson@linaro.org>
> Cc: Taniya Das <quic_tdas@quicinc.com>
> Cc: Satya Priya <quic_c_skakit@quicinc.com>
> Cc: Douglas Anderson <dianders@chromium.org>
> Cc: Matthias Kaehlcke <mka@chromium.org>
> Reported-by: Stephen Boyd <swboyd@chromium.org>
> Fixes: 1b771839de05 ("clk: qcom: gdsc: enable optional power domain support")
> Signed-off-by: Stephen Boyd <swboyd@chromium.org>
> ---
>
> Changes from v1 (https://lore.kernel.org/r/20221101233421.997149-1-swboyd@chromium.org):
> * Fix ret thinko
> * Update kerneldoc on 'dev' member
>
> drivers/clk/qcom/gdsc.c | 62 +++++------------------------------------
> drivers/clk/qcom/gdsc.h | 2 +-
> 2 files changed, 8 insertions(+), 56 deletions(-)

Though I'm not an expert, this seems reasonable to me and certainly an
improvement in that it no longer calls pm_runtime calls during the
"noirq" resume phase. Thus a non-expert:

Reviewed-by: Douglas Anderson <dianders@chromium.org>

This also seems to avoid the problems I reported [1]. Even though the
root cause (pm_runtime vs. clk prepare lock deadlock) is still
theoretically possible at least the problem is no longer tickled for
me (I tested on a sc7280-herobrine-villager board). Thus, I'm OK with:

Tested-by: Douglas Anderson <dianders@chromium.org>

[1] https://lore.kernel.org/r/20220922154354.2486595-1-dianders@chromium.org

\
 
 \ /
  Last update: 2022-11-03 00:36    [W:0.537 / U:0.080 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site