lkml.org 
[lkml]   [2022]   [Nov]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v3 2/3] arm64: dts: qcom: sm8450: add Soundwire and LPASS
From


On 16/11/2022 11:13, Krzysztof Kozlowski wrote:
> From: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
>
> Add Soundwire controllers, Low Power Audio SubSystem (LPASS) devices and
> LPASS pin controller.
>
> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
> Co-developed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
>
> ---
>
> Changes since v2:
> 1. Use lower-case hex.
>
> Changes since v1:
> 1. Whitespace cleanups.
> 2. Correct include - do not use deprecated one.
> ---
> arch/arm64/boot/dts/qcom/sm8450.dtsi | 295 +++++++++++++++++++++++++++
> 1 file changed, 295 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
> index 4b0a1eee8bd9..747440d0445a 100644
> --- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
> @@ -15,6 +15,7 @@
> #include <dt-bindings/interconnect/qcom,sm8450.h>
> #include <dt-bindings/soc/qcom,gpr.h>
> #include <dt-bindings/soc/qcom,rpmh-rsc.h>
> +#include <dt-bindings/sound/qcom,q6dsp-lpass-ports.h>
> #include <dt-bindings/thermal/thermal.h>
>
> / {
> @@ -2097,6 +2098,212 @@ compute-cb@3 {
> };
> };
>
> + wsa2macro: codec@31e0000 {
> + compatible = "qcom,sm8450-lpass-wsa-macro";
> + reg = <0 0x031e0000 0 0x1000>;
> + clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&vamacro>;
> + clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
> + assigned-clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
> + assigned-clock-rates = <19200000>, <19200000>;
> +
> + #clock-cells = <0>;
> + clock-output-names = "wsa2-mclk";
> + #sound-dai-cells = <1>;
I think I'm being a bit too picky, but #-cells could go as the last
bunch of properties.


> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&wsa2_swr_active>;
> + };
> +
> + /* WSA2 */
> + swr4: soundwire-controller@31f0000 {
> + reg = <0 0x031f0000 0 0x2000>;
> + compatible = "qcom,soundwire-v1.7.0";
> + interrupts = <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&wsa2macro>;
> + clock-names = "iface";
> +
> + qcom,din-ports = <2>;
> + qcom,dout-ports = <6>;
> +
> + qcom,ports-sinterval-low = /bits/ 8 <0x07 0x1f 0x3f 0x07 0x1f 0x3f 0x0f 0x0f>;
> + qcom,ports-offset1 = /bits/ 8 <0x01 0x02 0x0c 0x06 0x12 0x0d 0x07 0x0a>;
> + qcom,ports-offset2 = /bits/ 8 <0xff 0x00 0x1f 0xff 0x00 0x1f 0x00 0x00>;
> + qcom,ports-hstart = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
> + qcom,ports-hstop = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
> + qcom,ports-word-length = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
> + qcom,ports-block-pack-mode = /bits/ 8 <0xff 0xff 0x01 0xff 0xff 0x01 0xff 0xff>;
> + qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
> + qcom,ports-lane-control = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
> +
> + #sound-dai-cells = <1>;
> + #address-cells = <2>;
> + #size-cells = <0>;
> + };
> +
> + rxmacro: codec@3200000 {
> + compatible = "qcom,sm8450-lpass-rx-macro";
> + reg = <0 0x3200000 0 0x1000>;
> + clocks = <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&vamacro>;
> + clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
> +
> + assigned-clocks = <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
> + assigned-clock-rates = <19200000>, <19200000>;
> +
> + #clock-cells = <0>;
> + clock-output-names = "mclk";
> + #sound-dai-cells = <1>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&rx_swr_active>;
> + };
> +
> + swr1: soundwire-controller@3210000 {
> + reg = <0 0x3210000 0 0x2000>;
> + compatible = "qcom,soundwire-v1.7.0";
Some nodes have reg and compatible flipped.

> + interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&rxmacro>;
> + clock-names = "iface";
> + label = "RX";
> + qcom,din-ports = <0>;
> + qcom,dout-ports = <5>;
> +
> + qcom,ports-sinterval-low = /bits/ 8 <0x03 0x1f 0x1f 0x07 0x00>;
> + qcom,ports-offset1 = /bits/ 8 <0x00 0x00 0x0b 0x01 0x00>;
> + qcom,ports-offset2 = /bits/ 8 <0x00 0x00 0x0b 0x00 0x00>;
> + qcom,ports-hstart = /bits/ 8 <0xff 0x03 0xff 0xff 0xff>;
> + qcom,ports-hstop = /bits/ 8 <0xff 0x06 0xff 0xff 0xff>;
> + qcom,ports-word-length = /bits/ 8 <0x01 0x07 0x04 0xff 0xff>;
> + qcom,ports-block-pack-mode = /bits/ 8 <0xff 0x00 0x01 0xff 0xff>;
> + qcom,ports-lane-control = /bits/ 8 <0x01 0x00 0x00 0x00 0x00>;
> + qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff 0xff 0x00>;
> + #sound-dai-cells = <1>;
> + #address-cells = <2>;
> + #size-cells = <0>;
> + };
> +
> + txmacro: codec@3220000 {
> + compatible = "qcom,sm8450-lpass-tx-macro";
> + reg = <0 0x3220000 0 0x1000>;
> + clocks = <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&vamacro>;
> + clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
> + assigned-clocks = <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
> + assigned-clock-rates = <19200000>, <19200000>;
> +
> + #clock-cells = <0>;
> + clock-output-names = "mclk";
> + #sound-dai-cells = <1>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&tx_swr_active>;
> + };
> +
> + wsamacro: codec@3240000 {
> + compatible = "qcom,sm8450-lpass-wsa-macro";
> + reg = <0 0x03240000 0 0x1000>;
> + clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&vamacro>;
> + clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
> +
> + assigned-clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
> + assigned-clock-rates = <19200000>, <19200000>;
> +
> + #clock-cells = <0>;
> + clock-output-names = "mclk";
> + #sound-dai-cells = <1>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&wsa_swr_active>;
> + };
> +
> + /* WSA */
> + swr0: soundwire-controller@3250000 {
> + reg = <0 0x03250000 0 0x2000>;
> + compatible = "qcom,soundwire-v1.7.0";
> + interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&wsamacro>;
> + clock-names = "iface";
> +
> + qcom,din-ports = <2>;
> + qcom,dout-ports = <6>;
> +
> + qcom,ports-sinterval-low = /bits/ 8 <0x07 0x1f 0x3f 0x07 0x1f 0x3f 0x0f 0x0f>;
> + qcom,ports-offset1 = /bits/ 8 <0x01 0x02 0x0c 0x06 0x12 0x0d 0x07 0x0a>;
> + qcom,ports-offset2 = /bits/ 8 <0xff 0x00 0x1f 0xff 0x00 0x1f 0x00 0x00>;
> + qcom,ports-hstart = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
> + qcom,ports-hstop = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
> + qcom,ports-word-length = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
> + qcom,ports-block-pack-mode = /bits/ 8 <0xff 0xff 0x01 0xff 0xff 0x01 0xff 0xff>;
> + qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
> + qcom,ports-lane-control = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
> + qcom,port-offset = <1>;
> + #sound-dai-cells = <1>;
> + #address-cells = <2>;
> + #size-cells = <0>;
> + };
> +
> + swr2: soundwire-controller@33b0000 {
> + reg = <0 0x33b0000 0 0x2000>;
> + compatible = "qcom,soundwire-v1.7.0";
> + interrupts-extended = <&intc GIC_SPI 496 IRQ_TYPE_LEVEL_HIGH>,
> + <&intc GIC_SPI 520 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "core", "wake";
> +
> + clocks = <&vamacro>;
> + clock-names = "iface";
> + label = "TX";
> +
> + qcom,din-ports = <4>;
> + qcom,dout-ports = <0>;
> + qcom,ports-sinterval-low = /bits/ 8 <0x01 0x01 0x03 0x03>;
> + qcom,ports-offset1 = /bits/ 8 <0x00 0x00 0x01 0x01>;
> + qcom,ports-offset2 = /bits/ 8 <0x00 0x00 0x00 0x00>;
> + qcom,ports-block-pack-mode = /bits/ 8 <0xff 0xff 0xff 0xff>;
> + qcom,ports-hstart = /bits/ 8 <0xff 0xff 0xff 0xff>;
> + qcom,ports-hstop = /bits/ 8 <0xff 0xff 0xff 0xff>;
> + qcom,ports-word-length = /bits/ 8 <0xff 0xff 0xff 0xff>;
> + qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff 0xff>;
> + qcom,ports-lane-control = /bits/ 8 <0x01 0x02 0x00 0x00>;
> + qcom,port-offset = <1>;
> + #sound-dai-cells = <1>;
> + #address-cells = <2>;
> + #size-cells = <0>;
> + };
> +
> + vamacro: codec@33f0000 {
> + compatible = "qcom,sm8450-lpass-va-macro";
> + reg = <0 0x033f0000 0 0x1000>;
> + clocks = <&q6prmcc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
> + clock-names = "mclk", "macro", "dcodec", "npl";
> + assigned-clocks = <&q6prmcc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
> + assigned-clock-rates = <19200000>;
> +
> + #clock-cells = <0>;
> + clock-output-names = "fsgen";
> + #sound-dai-cells = <1>;
> + };
> +
> remoteproc_adsp: remoteproc@30000000 {
> compatible = "qcom,sm8450-adsp-pas";
> reg = <0 0x030000000 0 0x100>;
> @@ -3030,6 +3237,91 @@ qup_uart20_default: qup-uart20-default-state {
>
> };
>
> + lpass_tlmm: pinctrl@3440000{
> + compatible = "qcom,sm8450-lpass-lpi-pinctrl";
> + reg = <0 0x3440000 0x0 0x20000>,
> + <0 0x34d0000 0x0 0x10000>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-ranges = <&lpass_tlmm 0 0 23>;
> +
> + clocks = <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
> + clock-names = "core", "audio";
> +
> + wsa_swr_active: wsa-swr-active-state {
> + clk-pins {
> + pins = "gpio10";
> + function = "wsa_swr_clk";
> + drive-strength = <2>;
> + slew-rate = <1>;
> + bias-disable;
> + };
> +
> + data-pins {
> + pins = "gpio11";
> + function = "wsa_swr_data";
> + drive-strength = <2>;
> + slew-rate = <1>;
> + bias-bus-hold;
> + };
> + };
> +
> + tx_swr_active: tx-swr-active-state {
> + clk-pins {
> + pins = "gpio0";
> + function = "swr_tx_clk";
> + drive-strength = <2>;
> + slew-rate = <1>;
> + bias-disable;
> + };
> +
> + data-pins {
> + pins = "gpio1", "gpio2", "gpio14";
> + function = "swr_tx_data";
> + drive-strength = <2>;
> + slew-rate = <1>;
> + bias-bus-hold;
> + };
> + };
> +
> + rx_swr_active: rx-swr-active-state {
> + clk-pins {
> + pins = "gpio3";
> + function = "swr_rx_clk";
> + drive-strength = <2>;
> + slew-rate = <1>;
> + bias-disable;
> + };
> +
> + data-pins {
> + pins = "gpio4", "gpio5";
> + function = "swr_rx_data";
> + drive-strength = <2>;
> + slew-rate = <1>;
> + bias-bus-hold;
> + };
> + };
> +
> + wsa2_swr_active: wsa2-swr-active-state {
> + clk-pins {
> + pins = "gpio15";
> + function = "wsa2_swr_clk";
> + drive-strength = <2>;
> + slew-rate = <1>;
> + bias-disable;
> + };
> +
> + data-pins {
> + pins = "gpio16";
> + function = "wsa2_swr_data";
> + drive-strength = <2>;
> + slew-rate = <1>;
> + bias-bus-hold;
> + };
> + };
> + };
> +
> apps_smmu: iommu@15000000 {
> compatible = "qcom,sm8450-smmu-500", "arm,mmu-500";
> reg = <0 0x15000000 0 0x100000>;
> @@ -3507,6 +3799,9 @@ lpass_ag_noc: interconnect@3c40000 {
> };
> };
>
> + sound: sound {
> + };
You asked another folk working on sa8540p to not include sound in the
SoC dtsi.

Konrad

> +
> thermal-zones {
> aoss0-thermal {
> polling-delay-passive = <0>;

\
 
 \ /
  Last update: 2022-11-16 11:20    [W:0.205 / U:0.392 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site