lkml.org 
[lkml]   [2022]   [Oct]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH v22 2/2] ARM: dts: imx7d-remarkable2: Enable silergy,sy7636a
On Mon, Oct 24, 2022 at 08:58:53PM +1000, Alistair Francis wrote:
> Enable the silergy,sy7636a and silergy,sy7636a-regulator on the
> reMarkable2.
>
> Signed-off-by: Alistair Francis <alistair@alistair23.me>
> ---
> arch/arm/boot/dts/imx7d-remarkable2.dts | 62 +++++++++++++++++++++++++
> 1 file changed, 62 insertions(+)
>
> diff --git a/arch/arm/boot/dts/imx7d-remarkable2.dts b/arch/arm/boot/dts/imx7d-remarkable2.dts
> index a2a91bfdd98e..99ac0d242936 100644
> --- a/arch/arm/boot/dts/imx7d-remarkable2.dts
> +++ b/arch/arm/boot/dts/imx7d-remarkable2.dts
> @@ -22,6 +22,27 @@ memory@80000000 {
> reg = <0x80000000 0x40000000>;
> };
>
> + thermal-zones {
> + epd-thermal {
> + thermal-sensors = <&epd_pmic>;
> + polling-delay-passive = <30000>;
> + polling-delay = <30000>;

Have a newline between properties and child node.

> + trips {
> + trip0 {
> + temperature = <49000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + trip1 {
> + temperature = <50000>;
> + hysteresis = <2000>;
> + type = "critical";
> + };
> + };
> + };
> + };
> +
> reg_brcm: regulator-brcm {
> compatible = "regulator-fixed";
> regulator-name = "brcm_reg";
> @@ -84,6 +105,33 @@ wacom_digitizer: digitizer@9 {
> };
> };
>
> +&i2c4 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&pinctrl_i2c4>;
> + pinctrl-1 = <&pinctrl_i2c4>;
> + status = "okay";
> +
> + epd_pmic: sy7636a@62 {

Node name should be generic while label could be specific, so maybe:

sy7636a: pmic@62 {

> + compatible = "silergy,sy7636a";
> + reg = <0x62>;
> + status = "okay";

We usually end property list with `status`.

> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_epdpmic>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + #thermal-sensor-cells = <0>;
> +

Move this newline one line below.

> + epd-pwr-good-gpios = <&gpio6 21 GPIO_ACTIVE_HIGH>;
> + regulators {
> + reg_epdpmic: vcom {
> + regulator-name = "vcom";
> + regulator-boot-on;
> + };
> + };
> + };
> +};
> +
> &snvs_pwrkey {
> status = "okay";
> };
> @@ -177,6 +225,13 @@ MX7D_PAD_SAI1_TX_BCLK__GPIO6_IO13 0x14
> >;
> };
>
> + pinctrl_epdpmic: epdpmicgrp {
> + fsl,pins = <
> + MX7D_PAD_SAI2_RX_DATA__GPIO6_IO21 0x00000074
> + MX7D_PAD_ENET1_RGMII_TXC__GPIO7_IO11 0x00000014

You might want to align hex values like other pinctrl nodes?

Shawn

> + >;
> + };
> +
> pinctrl_i2c1: i2c1grp {
> fsl,pins = <
> MX7D_PAD_I2C1_SDA__I2C1_SDA 0x4000007f
> @@ -184,6 +239,13 @@ MX7D_PAD_I2C1_SCL__I2C1_SCL 0x4000007f
> >;
> };
>
> + pinctrl_i2c4: i2c4grp {
> + fsl,pins = <
> + MX7D_PAD_I2C4_SDA__I2C4_SDA 0x4000007f
> + MX7D_PAD_I2C4_SCL__I2C4_SCL 0x4000007f
> + >;
> + };
> +
> pinctrl_uart1: uart1grp {
> fsl,pins = <
> MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX 0x79
> --
> 2.37.3
>

\
 
 \ /
  Last update: 2022-10-29 10:52    [W:0.045 / U:0.292 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site