Messages in this thread | | | Date | Fri, 28 Oct 2022 09:21:09 +0800 | Subject | Re: [PATCH 2/2] net: hinic: Add control command support for VF PMD driver in DPDK | From | shaozhengchao <> |
| |
On 2022/10/26 20:59, Cai Huoqing wrote: > HINIC has a mailbox for PF-VF communication and the VF driver > could send port control command to PF driver via mailbox. > > The control command only can be set to register in PF, > so add support in PF driver for VF PMD driver control > command when VF PMD driver work with linux PF driver. > > Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev> > --- > .../net/ethernet/huawei/hinic/hinic_hw_dev.h | 64 +++++++++++++++++++ > .../net/ethernet/huawei/hinic/hinic_sriov.c | 18 ++++++ > 2 files changed, 82 insertions(+) > > diff --git a/drivers/net/ethernet/huawei/hinic/hinic_hw_dev.h b/drivers/net/ethernet/huawei/hinic/hinic_hw_dev.h > index abffd967a791..4f561e4e849a 100644 > --- a/drivers/net/ethernet/huawei/hinic/hinic_hw_dev.h > +++ b/drivers/net/ethernet/huawei/hinic/hinic_hw_dev.h > @@ -53,11 +53,15 @@ enum hinic_port_cmd { > > HINIC_PORT_CMD_SET_PFC = 0x5, > > + HINIC_PORT_CMD_SET_ETS = 0x7, > + HINIC_PORT_CMD_GET_ETS = 0x8, > + > HINIC_PORT_CMD_SET_MAC = 0x9, > HINIC_PORT_CMD_GET_MAC = 0xA, > HINIC_PORT_CMD_DEL_MAC = 0xB, > > HINIC_PORT_CMD_SET_RX_MODE = 0xC, > + HINIC_PORT_CMD_SET_ANTI_ATTACK_RATE = 0xD, > > HINIC_PORT_CMD_GET_PAUSE_INFO = 0x14, > HINIC_PORT_CMD_SET_PAUSE_INFO = 0x15, > @@ -81,6 +85,7 @@ enum hinic_port_cmd { > HINIC_PORT_CMD_GET_RSS_TEMPLATE_INDIR_TBL = 0x25, > > HINIC_PORT_CMD_SET_PORT_STATE = 0x29, > + HINIC_PORT_CMD_GET_PORT_STATE = 0x30, > > HINIC_PORT_CMD_SET_RSS_TEMPLATE_TBL = 0x2B, > HINIC_PORT_CMD_GET_RSS_TEMPLATE_TBL = 0x2C, > @@ -97,17 +102,29 @@ enum hinic_port_cmd { > > HINIC_PORT_CMD_RSS_CFG = 0x42, > > + HINIC_PORT_CMD_GET_PHY_TYPE = 0x44, > + > HINIC_PORT_CMD_FWCTXT_INIT = 0x45, > > HINIC_PORT_CMD_GET_LOOPBACK_MODE = 0x48, > HINIC_PORT_CMD_SET_LOOPBACK_MODE = 0x49, > > + HINIC_PORT_CMD_GET_JUMBO_FRAME_SIZE = 0x4A, > + HINIC_PORT_CMD_SET_JUMBO_FRAME_SIZE = 0x4B, > + > HINIC_PORT_CMD_ENABLE_SPOOFCHK = 0x4E, > > HINIC_PORT_CMD_GET_MGMT_VERSION = 0x58, > > + HINIC_PORT_CMD_GET_PORT_TYPE = 0x5B, > + > HINIC_PORT_CMD_SET_FUNC_STATE = 0x5D, > > + HINIC_PORT_CMD_GET_PORT_ID_BY_FUNC_ID = 0x5E, > + > + HINIC_PORT_CMD_GET_DMA_CS = 0x64, > + HINIC_PORT_CMD_SET_DMA_CS = 0x65, > + > HINIC_PORT_CMD_GET_GLOBAL_QPN = 0x66, > > HINIC_PORT_CMD_SET_VF_RATE = 0x69, > @@ -121,25 +138,72 @@ enum hinic_port_cmd { > > HINIC_PORT_CMD_SET_RQ_IQ_MAP = 0x73, > > + HINIC_PORT_CMD_SET_PFC_THD = 0x75, > + > HINIC_PORT_CMD_LINK_STATUS_REPORT = 0xA0, > > + HINIC_PORT_CMD_SET_LOSSLESS_ETH = 0xA3, > + > HINIC_PORT_CMD_UPDATE_MAC = 0xA4, > > HINIC_PORT_CMD_GET_CAP = 0xAA, > > + HINIC_PORT_CMD_UP_TC_ADD_FLOW = 0xAF, > + HINIC_PORT_CMD_UP_TC_DEL_FLOW = 0xB0, > + HINIC_PORT_CMD_UP_TC_GET_FLOW = 0xB1, > + > + HINIC_PORT_CMD_UP_TC_FLUSH_TCAM = 0xB2, > + > + HINIC_PORT_CMD_UP_TC_CTRL_TCAM_BLOCK = 0xB3, > + > + HINIC_PORT_CMD_UP_TC_ENABLE = 0xB4, > + > + HINIC_PORT_CMD_UP_TC_GET_TCAM_BLOCK = 0xB5, > + > + HINIC_PORT_CMD_SET_IPSU_MAC = 0xCB, > + HINIC_PORT_CMD_GET_IPSU_MAC = 0xCC, > + > + HINIC_PORT_CMD_SET_XSFP_STATUS = 0xD4, > HINIC_PORT_CMD_GET_LINK_MODE = 0xD9, > > HINIC_PORT_CMD_SET_SPEED = 0xDA, > > HINIC_PORT_CMD_SET_AUTONEG = 0xDB, > > + HINIC_PORT_CMD_CLEAR_QP_RES = 0xDD, > + > + HINIC_PORT_CMD_SET_SUPER_CQE = 0xDE, > + > + HINIC_PORT_CMD_SET_VF_COS = 0xDF, > + HINIC_PORT_CMD_GET_VF_COS = 0xE1, > + > + HINIC_PORT_CMD_CABLE_PLUG_EVENT = 0xE5, > + > + HINIC_PORT_CMD_LINK_ERR_EVENT = 0xE6, > + > + HINIC_PORT_CMD_SET_COS_UP_MAP = 0xE8, > + > + HINIC_PORT_CMD_RESET_LINK_CFG = 0xEB, > + > HINIC_PORT_CMD_GET_STD_SFP_INFO = 0xF0, > > + HINIC_PORT_CMD_FORCE_PKT_DROP = 0xF3, > + > HINIC_PORT_CMD_SET_LRO_TIMER = 0xF4, > > + HINIC_PORT_CMD_SET_VHD_CFG = 0xF7, > + > + HINIC_PORT_CMD_SET_LINK_FOLLOW = 0xF8, > + > HINIC_PORT_CMD_SET_VF_MAX_MIN_RATE = 0xF9, > > HINIC_PORT_CMD_GET_SFP_ABS = 0xFB, > + > + HINIC_PORT_CMD_Q_FILTER = 0xFC, > + > + HINIC_PORT_CMD_TCAM_FILTER = 0xFE, > + > + HINIC_PORT_CMD_SET_VLAN_FILTER = 0xFF > }; > > /* cmd of mgmt CPU message for HILINK module */ > diff --git a/drivers/net/ethernet/huawei/hinic/hinic_sriov.c b/drivers/net/ethernet/huawei/hinic/hinic_sriov.c > index a5f08b969e3f..bba41994dee6 100644 > --- a/drivers/net/ethernet/huawei/hinic/hinic_sriov.c > +++ b/drivers/net/ethernet/huawei/hinic/hinic_sriov.c > @@ -489,6 +489,24 @@ static struct vf_cmd_check_handle nic_cmd_support_vf[] = { > {HINIC_PORT_CMD_UPDATE_MAC, hinic_mbox_check_func_id_8B}, > {HINIC_PORT_CMD_GET_CAP, hinic_mbox_check_func_id_8B}, > {HINIC_PORT_CMD_GET_LINK_MODE, hinic_mbox_check_func_id_8B}, > + {HINIC_PORT_CMD_GET_VF_COS, NULL}, > + {HINIC_PORT_CMD_SET_VHD_CFG, hinic_mbox_check_func_id_8B}, > + {HINIC_PORT_CMD_SET_VLAN_FILTER, hinic_mbox_check_func_id_8B}, > + {HINIC_PORT_CMD_Q_FILTER, hinic_mbox_check_func_id_8B}, > + {HINIC_PORT_CMD_TCAM_FILTER, NULL}, > + {HINIC_PORT_CMD_UP_TC_ADD_FLOW, NULL}, > + {HINIC_PORT_CMD_UP_TC_DEL_FLOW, NULL}, > + {HINIC_PORT_CMD_UP_TC_FLUSH_TCAM, hinic_mbox_check_func_id_8B}, > + {HINIC_PORT_CMD_UP_TC_CTRL_TCAM_BLOCK, hinic_mbox_check_func_id_8B}, > + {HINIC_PORT_CMD_UP_TC_ENABLE, hinic_mbox_check_func_id_8B}, > + {HINIC_PORT_CMD_CABLE_PLUG_EVENT, NULL}, > + {HINIC_PORT_CMD_LINK_ERR_EVENT, NULL}, > + {HINIC_PORT_CMD_SET_PORT_STATE, hinic_mbox_check_func_id_8B}, > + {HINIC_PORT_CMD_SET_ETS, NULL}, > + {HINIC_PORT_CMD_SET_ANTI_ATTACK_RATE, NULL}, > + {HINIC_PORT_CMD_RESET_LINK_CFG, hinic_mbox_check_func_id_8B}, > + {HINIC_PORT_CMD_SET_LINK_FOLLOW, NULL}, > + {HINIC_PORT_CMD_CLEAR_QP_RES, NULL}, > }; > > #define CHECK_IPSU_15BIT 0X8000 Hi Cai: I guess how do you get the opcodes of these commands? Have they all been tested? Is the test result consistent with the driver released on the Huawei support website?
Zhengchao Shao
| |