lkml.org 
[lkml]   [2022]   [Oct]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v4 1/2] dt-bindings: mtd: marvell-nand: Convert to YAML DT scheme
On Tue, 25 Oct 2022 09:51:14 -0400, Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> wrote:
> On 25/10/2022 08:52, Vadym Kochan wrote:
> > On Tue, 25 Oct 2022 08:25:01 -0400, Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> wrote:
> >> On 25/10/2022 06:17, Vadym Kochan wrote:
> >>> Switch the DT binding to a YAML schema to enable the DT validation.
> >>>
> >>> Dropped deprecated compatibles and properties described in txt file.
> >>>
> >>> Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
> >>> ---
> >>>
> >>> v4:
> >>> 1) Remove "label" and "partitions" properties
> >>
> >> I think you did not read the feedback.
> >>
> >>
> >> (...)
> >>
> >>> +
> >>> + marvell,system-controller:
> >>> + $ref: /schemas/types.yaml#/definitions/phandle
> >>> + description: Syscon node that handles NAND controller related registers
> >>> +
> >>> +patternProperties:
> >>> + "^nand@[0-3]$":
> >>> + type: object
> >>> + properties:
> >>> + reg:
> >>> + minimum: 0
> >>> + maximum: 3
> >>> +
> >>> + nand-rb:
> >>> + minimum: 0
> >>> + maximum: 1
> >>> +
> >>> + nand-ecc-strength:
> >>> + enum: [1, 4, 8]
> >>> +
> >>> + nand-on-flash-bbt: true
> >>> +
> >>> + nand-ecc-mode: true
> >>> +
> >>> + nand-ecc-algo:
> >>> + description: |
> >>> + This property is essentially useful when not using hardware ECC.
> >>> + Howerver, it may be added when using hardware ECC for clarification
> >>> + but will be ignored by the driver because ECC mode is chosen depending
> >>> + on the page size and the strength required by the NAND chip.
> >>> + This value may be overwritten with nand-ecc-strength property.
> >>> +
> >>> + nand-ecc-step-size:
> >>> + description: |
> >>> + Marvell's NAND flash controller does use fixed strength
> >>> + (1-bit for Hamming, 16-bit for BCH), so the actual step size
> >>> + will shrink or grow in order to fit the required strength.
> >>> + Step sizes are not completely random for all and follow certain
> >>> + patterns described in AN-379, "Marvell SoC NFC ECC".
> >>> +
> >>> + marvell,nand-keep-config:
> >>> + description: |
> >>> + Orders the driver not to take the timings from the core and
> >>> + leaving them completely untouched. Bootloader timings will then
> >>> + be used.
> >>> + $ref: /schemas/types.yaml#/definitions/flag
> >>> +
> >>> + marvell,nand-enable-arbiter:
> >>> + description: |
> >>> + To enable the arbiter, all boards blindly used it,
> >>> + this bit was set by the bootloader for many boards and even if
> >>> + it is marked reserved in several datasheets, it might be needed to set
> >>> + it (otherwise it is harmless) so whether or not this property is set,
> >>> + the bit is selected by the driver.
> >>> + $ref: /schemas/types.yaml#/definitions/flag
> >>> + deprecated: true
> >>> +
> >>> + required:
> >>> + - reg
> >>> + - nand-rb
> >>
> >> I have no clue why you are doing some random changes. Now you dropped
> >> additionalProperties for nand@ about which no one asked you to drop.
> >>
> >> No. It *must* be here.
> >
> > Sorry for this mess, I was confused with the "label" and "partitions"
> > because I got errors about these properties when I used only
> > "additionalProperties: false", so I tried to put reference to partition.yaml.
> >
> > Then I looked at other nand-controllers schemas and I did not find inclusion of partition.yaml
> > for them so I decided to just drop it at all. My understanding is that "additionalProperties:false"
> > is needed for nand@ if to have "label" and "partitions" properties, otherwise it is not needed.
>
> A final schema (not used by other schemas) must always finish with
> additional/unevaluatedProperties false. You have errors since beginning
> - I wrote about it in your first patchset (v1). You had error visible
> after adding proper unevaluatedProperties in proper place.
>
> You have partitions node, for partitions. But you reference only *one*
> partition.

Yes, sorry for that.

OK, I think I need to do this in nand@:

...

label:
$ref: /schemas/types.yaml#/definitions/string

partitions:
type: object

...

additionalProperties: false

So the "partitions" will be validated for example by fixed-partitions.yaml.
And additionalProperties:false in the nand@ protects from adding other
non-valid properties on it's hierarchy level since all possible
properties in nand@ are covered.

>
> Best regards,
> Krzysztof
>

\
 
 \ /
  Last update: 2022-10-25 18:17    [W:2.710 / U:0.024 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site