lkml.org 
[lkml]   [2022]   [Oct]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v20 2/2] dt-bindings: fpga: document Lattice sysCONFIG FPGA manager
Date
Add Device Tree Binding doc for configuring Lattice ECP5 FPGA over
Slave SPI sysCONFIG interface.

Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
.../bindings/fpga/lattice,sysconfig.yaml | 81 +++++++++++++++++++
1 file changed, 81 insertions(+)
create mode 100644 Documentation/devicetree/bindings/fpga/lattice,sysconfig.yaml

diff --git a/Documentation/devicetree/bindings/fpga/lattice,sysconfig.yaml b/Documentation/devicetree/bindings/fpga/lattice,sysconfig.yaml
new file mode 100644
index 000000000000..4fb05eb84e2a
--- /dev/null
+++ b/Documentation/devicetree/bindings/fpga/lattice,sysconfig.yaml
@@ -0,0 +1,81 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/fpga/lattice,sysconfig.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Lattice Slave SPI sysCONFIG FPGA manager
+
+maintainers:
+ - Ivan Bornyakov <i.bornyakov@metrotek.ru>
+
+description: |
+ Lattice sysCONFIG port, which is used for FPGA configuration, among others,
+ have Slave Serial Peripheral Interface. Only full reconfiguration is
+ supported.
+
+ Programming of ECP5 is done by writing uncompressed bitstream image in .bit
+ format into FPGA's SRAM configuration memory.
+
+properties:
+ compatible:
+ enum:
+ - lattice,sysconfig-ecp5
+
+ reg:
+ maxItems: 1
+
+ program-gpios:
+ description:
+ A GPIO line connected to PROGRAMN (active low) pin of the device.
+ Initiates configuration sequence.
+ maxItems: 1
+
+ init-gpios:
+ description:
+ A GPIO line connected to INITN (active low) pin of the device.
+ Indicates that the FPGA is ready to be configured.
+ maxItems: 1
+
+ done-gpios:
+ description:
+ A GPIO line connected to DONE (active high) pin of the device.
+ Indicates that the configuration sequence is complete.
+ maxItems: 1
+
+required:
+ - compatible
+ - reg
+
+allOf:
+ - $ref: /schemas/spi/spi-peripheral-props.yaml
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: lattice,sysconfig-ecp5
+ then:
+ properties:
+ spi-max-frequency:
+ maximum: 60000000
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+
+ spi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fpga-mgr@0 {
+ compatible = "lattice,sysconfig-ecp5";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ program-gpios = <&gpio3 4 GPIO_ACTIVE_LOW>;
+ init-gpios = <&gpio3 3 GPIO_ACTIVE_LOW>;
+ done-gpios = <&gpio3 2 GPIO_ACTIVE_HIGH>;
+ };
+ };
--
2.37.4

\
 
 \ /
  Last update: 2022-10-25 07:40    [W:0.036 / U:0.560 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site