Messages in this thread Patch in this message | | | Date | Mon, 24 Oct 2022 13:50:50 +0100 | From | Paul Cercueil <> | Subject | Re: [PATCH v2 2/2] serial: 8250/ingenic: Add support for the JZ4750/JZ4755 |
| |
Hi Siarhei,
Le sam. 22 oct. 2022 à 18:12:24 +0300, Siarhei Volkau <lis8215@gmail.com> a écrit : > JZ4750/55/60 (but not JZ4760b) have an extra divisor in between extclk > and peripheral clock, called CPCCR.ECS, the driver can't figure out > the > real state of the divisor without dirty hack - peek CGU CPCCR > register. > However, we can rely on a vendor's bootloader (u-boot 1.1.6) behavior: > if (extclk > 16MHz) > the divisor is enabled, so the UART driving clock is extclk/2. > > This behavior relies on hardware differences: most boards (if not all) > with those SoCs have 12 or 24 MHz oscillators but many peripherals > want > 12Mhz to operate properly (AIC and USB-PHY at least). > > The patch doesn't affect JZ4760's behavior as it is subject for > another > patchset with re-classification of all supported ingenic UARTs. > > Link: > https://github.com/carlos-wong/uboot_jz4755/blob/master/cpu/mips/jz_serial.c#L158 > Signed-off-by: Siarhei Volkau <lis8215@gmail.com> > --- > drivers/tty/serial/8250/8250_ingenic.c | 50 > ++++++++++++++++++++++---- > 1 file changed, 43 insertions(+), 7 deletions(-) > > diff --git a/drivers/tty/serial/8250/8250_ingenic.c > b/drivers/tty/serial/8250/8250_ingenic.c > index 2b2f5d8d2..3ffa6b722 100644 > --- a/drivers/tty/serial/8250/8250_ingenic.c > +++ b/drivers/tty/serial/8250/8250_ingenic.c > @@ -87,24 +87,19 @@ static void __init > ingenic_early_console_setup_clock(struct earlycon_device *dev > dev->port.uartclk = be32_to_cpup(prop); > } > > -static int __init ingenic_early_console_setup(struct earlycon_device > *dev, > - const char *opt) > +static int __init ingenic_earlycon_setup_tail(struct earlycon_device > *dev, > + const char *opt) > { > struct uart_port *port = &dev->port; > unsigned int divisor; > int baud = 115200; > > - if (!dev->port.membase) > - return -ENODEV;
You can keep this here - no need to move it (and it'd avoid duplicating code).
> - > if (opt) { > unsigned int parity, bits, flow; /* unused for now */ > > uart_parse_options(opt, &baud, &parity, &bits, &flow); > } > > - ingenic_early_console_setup_clock(dev); > - > if (dev->baud) > baud = dev->baud; > divisor = DIV_ROUND_CLOSEST(port->uartclk, 16 * baud); > @@ -129,9 +124,49 @@ static int __init > ingenic_early_console_setup(struct earlycon_device *dev, > return 0; > } > > +static int __init ingenic_early_console_setup(struct earlycon_device > *dev, > + const char *opt) > +{ > + if (!dev->port.membase) > + return -ENODEV; > + > + ingenic_early_console_setup_clock(dev); > + > + ingenic_earlycon_setup_tail(dev, opt); > +} > + > +static int __init jz4750_early_console_setup(struct earlycon_device > *dev, > + const char *opt) > +{ > + if (!dev->port.membase) > + return -ENODEV; > + > + /* > + * JZ4750/55/60 (not JZ4760b) have an extra divisor > + * between extclk and peripheral clock, the > + * driver can't figure out the real state of the > + * divisor without dirty hacks (peek CGU register). > + * However, we can rely on a vendor's behavior: > + * if (extclk > 16MHz) > + * the divisor is enabled. > + * This behavior relies on hardware differences: > + * most boards with those SoCs have 12 or 24 MHz > + * oscillators but many peripherals want 12Mhz > + * to operate properly (AIC and USB-phy at least). > + */ > + ingenic_early_console_setup_clock(dev); > + if (dev->port.uartclk > 16000000) > + dev->port.uartclk /= 2;
I would assume you could just do: dev->port.uartclk = 12000000;
Since you'd always get a 12 MHz clock (either with a 12 MHz oscillator or a 24 MHz oscillator with a /2 divider).
With that said - I am fine with that code, it would allow to fine-tune the oscillator value (although I hightly doubt anybody is going to do that).
The 16 MHz value sounds very arbitrary, but I'll give it a pass.
Cheers, -Paul
> + > + ingenic_earlycon_setup_tail(dev, opt); > +} > + > OF_EARLYCON_DECLARE(jz4740_uart, "ingenic,jz4740-uart", > ingenic_early_console_setup); > > +OF_EARLYCON_DECLARE(jz4750_uart, "ingenic,jz4750-uart", > + jz4750_early_console_setup); > + > OF_EARLYCON_DECLARE(jz4770_uart, "ingenic,jz4770-uart", > ingenic_early_console_setup); > > @@ -328,6 +363,7 @@ static const struct ingenic_uart_config > x1000_uart_config = { > > static const struct of_device_id of_match[] = { > { .compatible = "ingenic,jz4740-uart", .data = &jz4740_uart_config > }, > + { .compatible = "ingenic,jz4750-uart", .data = &jz4760_uart_config > }, > { .compatible = "ingenic,jz4760-uart", .data = &jz4760_uart_config > }, > { .compatible = "ingenic,jz4770-uart", .data = &jz4760_uart_config > }, > { .compatible = "ingenic,jz4775-uart", .data = &jz4760_uart_config > }, > -- > 2.36.1 >
| |