lkml.org 
[lkml]   [2022]   [Oct]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH RESEND] scsi: ufs: core: Let delay value after LPM can be modified by vendor
Avri Altman <Avri.Altman@wdc.com> 于2022年10月20日周四 15:16写道:
>
> > From: Zhe Wang <zhe.wang1@unisoc.com>
> >
> > Some UFS devices require that the VCC should drop below 0.1V after
> > turning off, otherwise device may not resume successfully. And
> > because the power-off rate is different on different SOC platforms.
> > Therefore, we hope that the delay can be modified by vendor to
> > adjust the most appropriate delay value.
> >
> > Signed-off-by: Zhe Wang <zhe.wang1@unisoc.com>
> > ---
> > drivers/ufs/core/ufshcd.c | 11 +++++++++--
> > include/ufs/ufshcd.h | 2 ++
> > 2 files changed, 11 insertions(+), 2 deletions(-)
> >
> > diff --git a/drivers/ufs/core/ufshcd.c b/drivers/ufs/core/ufshcd.c
> > index 7256e6c43ca6..f6350231da0e 100644
> > --- a/drivers/ufs/core/ufshcd.c
> > +++ b/drivers/ufs/core/ufshcd.c
> > @@ -89,6 +89,9 @@
> > /* Polling time to wait for fDeviceInit */
> > #define FDEVICEINIT_COMPL_TIMEOUT 1500 /* millisecs */
> >
> > +/* Default value of turn off VCC rail: 5000us */
> > +#define UFS_VCC_TURNOFF_DELAY_US 5000
> > +
> > #define ufshcd_toggle_vreg(_dev, _vreg, _on) \
> > ({ \
> > int _ret; \
> > @@ -7784,6 +7787,9 @@ static int ufs_get_device_desc(struct ufs_hba
> > *hba)
> >
> > ufs_fixup_device_setup(hba);
> >
> > + if (hba->dev_quirks & UFS_DEVICE_QUIRK_DELAY_AFTER_LPM &&
> > !hba->vcc_turnoff_delay)
> > + hba->vcc_turnoff_delay = UFS_VCC_TURNOFF_DELAY_US;
> Couldn't find where otherwise you are setting this value?
> Also, UFS_DEVICE_QUIRK_DELAY_AFTER_LPM is only set for MTK.
> Are you planning at some point adding your own host driver?
>

We are still preparing and discussing our own UFS host driver code,
which will be uploaded once we are done.

> > +
> > ufshcd_wb_probe(hba, desc_buf);
> >
> > ufshcd_temp_notif_probe(hba, desc_buf);
> > @@ -8917,8 +8923,9 @@ static void ufshcd_vreg_set_lpm(struct ufs_hba
> > *hba)
> > * Some UFS devices require delay after VCC power rail is turned-off.
> > */
> > if (vcc_off && hba->vreg_info.vcc &&
> > - hba->dev_quirks & UFS_DEVICE_QUIRK_DELAY_AFTER_LPM)
> > - usleep_range(5000, 5100);
> > + hba->dev_quirks & UFS_DEVICE_QUIRK_DELAY_AFTER_LPM &&
> > + hba->vcc_turnoff_delay)
> > + usleep_range(hba->vcc_turnoff_delay, hba->vcc_turnoff_delay +
> > 100);
> > }
> >
> > #ifdef CONFIG_PM
> > diff --git a/include/ufs/ufshcd.h b/include/ufs/ufshcd.h
> > index 9f28349ebcff..bfde3cb962fb 100644
> > --- a/include/ufs/ufshcd.h
> > +++ b/include/ufs/ufshcd.h
> > @@ -828,6 +828,7 @@ struct ufs_hba_monitor {
> > * device
> > * @complete_put: whether or not to call ufshcd_rpm_put() from inside
> > * ufshcd_resume_complete()
> > + * @vcc_turnoff_delay: VCC turnoff delay value.
> > */
> > struct ufs_hba {
> > void __iomem *mmio_base;
> > @@ -975,6 +976,7 @@ struct ufs_hba {
> > #endif
> > u32 luns_avail;
> > bool complete_put;
> > + u32 vcc_turnoff_delay;
> Can this be part of struct ufs_vreg instead?
> Also maybe vcc_turnoff_delay_us?
>
> Thanks,
> Avri
> > };
> >
> > /* Returns true if clocks can be gated. Otherwise false */
> > --
> > 2.17.1
>

Thanks for your suggestion, I will modify it in V2.

Thanks,
Zhe Wang

\
 
 \ /
  Last update: 2022-10-20 11:18    [W:1.445 / U:0.012 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site