lkml.org 
[lkml]   [2022]   [Oct]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH] arm64: dts: meson: Enable active coling using gpio-fan on Odroid N2/N2+
Hi Neil

On Wed, 19 Oct 2022 at 16:39, Neil Armstrong <neil.armstrong@linaro.org> wrote:
>
> Hi Anand,
>
> On 19/10/2022 11:48, Anand Moon wrote:
> > Hi Martin,
> >
> > On Wed, 19 Oct 2022 at 08:36, Anand Moon <linux.amoon@gmail.com> wrote:
> >>
> >> Hi Martin,
> >>
> >> On Wed, 19 Oct 2022 at 02:46, Martin Blumenstingl
> >> <martin.blumenstingl@googlemail.com> wrote:
> >>>
> >>> Hello Anand,
> >>>
> >>> On Tue, Oct 18, 2022 at 9:53 PM Anand Moon <linux.amoon@gmail.com> wrote:
> >>>>
> >>>> Odroid N2/N2+ support active cooling via gpio-fan controller.
> >>>> Add fan controls and tip point for cpu and ddr thermal sensor
> >>>> on this boards.
> >>> In the schematics for board rev 0.6 [0] I cannot find any information
> >>> about a fan connector.
> >>> The schematics for board rev 0.3 [1] on the other hand document a PWM
> >>> based fan connector on page 16.
> >>> So now I am not sure whether your patch only applies to certain board
> >>> revisions, the schematics are incorrect, etc.
> >>>
> >>> Can you please provide some details about the fan connector on
> >>> Odroid-N2/N2+ and which hardware revisions are supported (and which
> >>> aren't) by your patch?
> >>>
> >>>
> >> Ok I got this wrong the schematics below there is pwm controller, not
> >> gpio controller
> >> GPIOAO.BIT10 (PWM)
> >> I will correct the patch sorry for the mistake I did not look more carefully.
> >>
> >
> > As per the schematics GPIOAO_10 is controlled by PWMAO_D
> > But looking into the datasheet [0] I could not find the relevant
> > PWMAO_D pmw ip block to link the fan to the PWM controller.
> >
> > [0] https://dn.odroid.com/S922X/ODROID-N2/Datasheet/S922X_Public_Datasheet_V0.2.pdf
> >
> > I could get the PWM node but is not working for me.
> >
> > @@ -547,6 +588,14 @@ &pwm_ab {
> > status = "okay";
> > };
> >
> > +&pwm_AO_ab {
>
> &pwm_AO_cd not _ab
>
No it has a conflict with CPU_B (vddcpu_b) PWM

I have tried linking all the PWM with pwm-fan but it's not working.

# sudo cat /sys/kernel/debug/pwm
platform/ffd1b000.pwm, 2 PWM devices
pwm-0 (regulator-vddcpu-a ): requested enabled period: 1250 ns
duty: 0 ns polarity: normal
pwm-1 ((null) ): period: 0 ns duty: 0 ns polarity: normal

platform/ff807000.pwm, 2 PWM devices
pwm-0 ((null) ): period: 0 ns duty: 0 ns polarity: normal
pwm-1 (pwm-fan ): requested period: 1250 ns duty: 0 ns
polarity: normal

platform/ff802000.pwm, 2 PWM devices
pwm-0 ((null) ): period: 0 ns duty: 0 ns polarity: normal
pwm-1 (regulator-vddcpu-b ): requested enabled period: 1250 ns
duty: 88 ns polarity: normal

Thanks
-Anand

\
 
 \ /
  Last update: 2022-10-19 19:19    [W:0.050 / U:1.136 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site