lkml.org 
[lkml]   [2022]   [Oct]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH V2 3/3] Input: elantech - Fix incorrectly halved touchpad range on ELAN v3 touchpads
Date
On Linux 5.19.10, on my laptop (Dell Inspiron 15R SE 7520) with an Elan
v3 touchpad (dmesg says "with firmware version 0x450f02"), the reported
size of my touchpad (in userspace by calling mtdev_configure() and
libevdev_get_abs_maximum(), in kernel space
elantech_device_info::x_max/y_max, either way 1470 by 700) is half that
of the actual touch range (2940 by 1400), and the upper half of my
touchpad reports negative values. As a result, with the Synaptics or
libinput X11 driver set to edge scrolling mode, the entire right half of
my touchpad has x-values past evdev's reported maximum size, and acts as
a giant scrollbar!

The problem is that elantech_setup_ps2() -> elantech_set_absolute_mode()
sets up absolute mode and doubles the hardware resolution (doubling the
hardware's maximum reported x/y coordinates and its response to
ETP_FW_ID_QUERY), *after* elantech_query_info() fetches the touchpad
coordinate system size using ETP_FW_ID_QUERY, which gets cached and
reported to userspace through ioctl(fd, EVIOCGABS(ABS_X/Y), ...). So the
touchpad size reported to userspace (and used to subtract vertical
coordinates from) is half the maximum position of actual touches.

This patch splits out a function elantech_query_range_v3() which fetches
*only* ETP_FW_ID_QUERY (touchpad size), and calls it a second time if
elantech_set_absolute_mode() enables double-size mode. This means the
first call is redundant and wasted if a second call occurs, but this
minimizes the need to restructure the driver.

Link: https://lore.kernel.org/linux-input/CAL57YxZNutUVxBtvbVWKMw-V2kqeVB5kTQ5BFdJmN=mdPq8Q8Q@mail.gmail.com/
Link: https://lore.kernel.org/linux-input/20221008093437.72d0f6b0@dell-void.nyanpasu256.gmail.com.beta.tailscale.net/
Fixes: 37548659bb22 ("Input: elantech - query the min/max information beforehand too")
Signed-off-by: Eirin Nya <nyanpasu256@gmail.com>
---

Notes:
Should we move (elantech_set_absolute_mode ->
elantech_write_reg(...0x0b or 0x01)) *earlier* into elantech_query_info()
before "query range information"? See discussion at
https://lore.kernel.org/linux-input/20221008093437.72d0f6b0@dell-void.nyanpasu256.gmail.com.beta.tailscale.net/

drivers/input/mouse/elantech.c | 30 ++++++++++++++++++++++++++----
1 file changed, 26 insertions(+), 4 deletions(-)

diff --git a/drivers/input/mouse/elantech.c b/drivers/input/mouse/elantech.c
index 263779c031..a2176f0fd3 100644
--- a/drivers/input/mouse/elantech.c
+++ b/drivers/input/mouse/elantech.c
@@ -1006,6 +1006,9 @@ static void elantech_set_rate_restore_reg_07(struct psmouse *psmouse,
psmouse_err(psmouse, "restoring reg_07 failed\n");
}

+static int elantech_query_range_v3(struct psmouse *psmouse,
+ struct elantech_device_info *info);
+
/*
* Put the touchpad into absolute mode
*/
@@ -1047,6 +1050,14 @@ static int elantech_set_absolute_mode(struct psmouse *psmouse)
if (elantech_write_reg(psmouse, 0x10, etd->reg_10))
rc = -1;

+ /*
+ * If we boost hardware resolution, we have to re-query
+ * info->x_max and y_max.
+ */
+ if (etd->info.set_hw_resolution)
+ if (elantech_query_range_v3(psmouse, &etd->info))
+ rc = -1;
+
break;

case 4:
@@ -1671,6 +1682,20 @@ static int elantech_set_properties(struct elantech_device_info *info)
return 0;
}

+static int elantech_query_range_v3(struct psmouse *psmouse,
+ struct elantech_device_info *info)
+{
+ unsigned char param[3];
+
+ if (info->send_cmd(psmouse, ETP_FW_ID_QUERY, param))
+ return -EINVAL;
+
+ info->x_max = (0x0f & param[0]) << 8 | param[1];
+ info->y_max = (0xf0 & param[0]) << 4 | param[2];
+
+ return 0;
+}
+
static int elantech_query_info(struct psmouse *psmouse,
struct elantech_device_info *info)
{
@@ -1826,11 +1851,8 @@ static int elantech_query_info(struct psmouse *psmouse,
break;

case 3:
- if (info->send_cmd(psmouse, ETP_FW_ID_QUERY, param))
+ if (elantech_query_range_v3(psmouse, info))
return -EINVAL;
-
- info->x_max = (0x0f & param[0]) << 8 | param[1];
- info->y_max = (0xf0 & param[0]) << 4 | param[2];
break;

case 4:
--
2.38.0
\
 
 \ /
  Last update: 2022-10-14 13:17    [W:1.461 / U:0.012 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site