lkml.org 
[lkml]   [2022]   [Oct]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH 1/6] dt-bindings: usb: ci-hdrc-usb2: convert to yaml
From
On 10/10/2022 06:18, Peng Fan (OSS) wrote:
> From: Peng Fan <peng.fan@nxp.com>
>
> Convert the binding to yaml format
>
> Signed-off-by: Peng Fan <peng.fan@nxp.com>
> ---
> .../devicetree/bindings/usb/ci-hdrc-usb2.txt | 158 ---------
> .../devicetree/bindings/usb/ci-hdrc-usb2.yaml | 306 ++++++++++++++++++
> 2 files changed, 306 insertions(+), 158 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt
> create mode 100644 Documentation/devicetree/bindings/usb/ci-hdrc-usb2.yaml
>
> diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt
> deleted file mode 100644
> index ba51fb1252b9..000000000000
> --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt
> +++ /dev/null
> @@ -1,158 +0,0 @@
> -* USB2 ChipIdea USB controller for ci13xxx
> -
> -Required properties:
> -- compatible: should be one of:
> - "fsl,imx23-usb"
> - "fsl,imx27-usb"
> - "fsl,imx28-usb"
> - "fsl,imx6q-usb"
> - "fsl,imx6sl-usb"
> - "fsl,imx6sx-usb"
> - "fsl,imx6ul-usb"
> - "fsl,imx7d-usb"
> - "fsl,imx7ulp-usb"
> - "lsi,zevio-usb"
> - "qcom,ci-hdrc"
> - "chipidea,usb2"
> - "xlnx,zynq-usb-2.20a"
> - "nvidia,tegra20-udc"
> - "nvidia,tegra30-udc"
> - "nvidia,tegra114-udc"
> - "nvidia,tegra124-udc"
> -- reg: base address and length of the registers
> -- interrupts: interrupt for the USB controller
> -
> -Recommended properies:
> -- phy_type: the type of the phy connected to the core. Should be one
> - of "utmi", "utmi_wide", "ulpi", "serial" or "hsic". Without this
> - property the PORTSC register won't be touched.
> -- dr_mode: One of "host", "peripheral" or "otg". Defaults to "otg"
> -
> -Deprecated properties:
> -- usb-phy: phandle for the PHY device. Use "phys" instead.
> -- fsl,usbphy: phandle of usb phy that connects to the port. Use "phys" instead.
> -
> -Optional properties:
> -- clocks: reference to the USB clock
> -- phys: reference to the USB PHY
> -- phy-names: should be "usb-phy"
> -- vbus-supply: reference to the VBUS regulator
> -- maximum-speed: limit the maximum connection speed to "full-speed".
> -- tpl-support: TPL (Targeted Peripheral List) feature for targeted hosts
> -- itc-setting: interrupt threshold control register control, the setting
> - should be aligned with ITC bits at register USBCMD.
> -- ahb-burst-config: it is vendor dependent, the required value should be
> - aligned with AHBBRST at SBUSCFG, the range is from 0x0 to 0x7. This
> - property is used to change AHB burst configuration, check the chipidea
> - spec for meaning of each value. If this property is not existed, it
> - will use the reset value.
> -- tx-burst-size-dword: it is vendor dependent, the tx burst size in dword
> - (4 bytes), This register represents the maximum length of a the burst
> - in 32-bit words while moving data from system memory to the USB
> - bus, the value of this property will only take effect if property
> - "ahb-burst-config" is set to 0, if this property is missing the reset
> - default of the hardware implementation will be used.
> -- rx-burst-size-dword: it is vendor dependent, the rx burst size in dword
> - (4 bytes), This register represents the maximum length of a the burst
> - in 32-bit words while moving data from the USB bus to system memory,
> - the value of this property will only take effect if property
> - "ahb-burst-config" is set to 0, if this property is missing the reset
> - default of the hardware implementation will be used.
> -- extcon: phandles to external connector devices. First phandle should point to
> - external connector, which provide "USB" cable events, the second should point
> - to external connector device, which provide "USB-HOST" cable events. If one
> - of the external connector devices is not required, empty <0> phandle should
> - be specified.
> -- phy-clkgate-delay-us: the delay time (us) between putting the PHY into
> - low power mode and gating the PHY clock.
> -- non-zero-ttctrl-ttha: after setting this property, the value of register
> - ttctrl.ttha will be 0x7f; if not, the value will be 0x0, this is the default
> - value. It needs to be very carefully for setting this property, it is
> - recommended that consult with your IC engineer before setting this value.
> - On the most of chipidea platforms, the "usage_tt" flag at RTL is 0, so this
> - property only affects siTD.
> - If this property is not set, the max packet size is 1023 bytes, and if
> - the total of packet size for pervious transactions are more than 256 bytes,
> - it can't accept any transactions within this frame. The use case is single
> - transaction, but higher frame rate.
> - If this property is set, the max packet size is 188 bytes, it can handle
> - more transactions than above case, it can accept transactions until it
> - considers the left room size within frame is less than 188 bytes, software
> - needs to make sure it does not send more than 90%
> - maximum_periodic_data_per_frame. The use case is multiple transactions, but
> - less frame rate.
> -- mux-controls: The mux control for toggling host/device output of this
> - controller. It's expected that a mux state of 0 indicates device mode and a
> - mux state of 1 indicates host mode.
> -- mux-control-names: Shall be "usb_switch" if mux-controls is specified.
> -- pinctrl-names: Names for optional pin modes in "default", "host", "device".
> - In case of HSIC-mode, "idle" and "active" pin modes are mandatory. In this
> - case, the "idle" state needs to pull down the data and strobe pin
> - and the "active" state needs to pull up the strobe pin.
> -- pinctrl-n: alternate pin modes
> -
> -i.mx specific properties
> -- fsl,usbmisc: phandler of non-core register device, with one
> - argument that indicate usb controller index
> -- disable-over-current: disable over current detect
> -- over-current-active-low: over current signal polarity is active low.
> -- over-current-active-high: over current signal polarity is active high.
> - It's recommended to specify the over current polarity.
> -- power-active-high: power signal polarity is active high
> -- external-vbus-divider: enables off-chip resistor divider for Vbus
> -- samsung,picophy-pre-emp-curr-control: HS Transmitter Pre-Emphasis Current
> - Control. This signal controls the amount of current sourced to the
> - USB_OTG*_DP and USB_OTG*_DN pins after a J-to-K or K-to-J transition.
> - The range is from 0x0 to 0x3, the default value is 0x1.
> - Details can refer to TXPREEMPAMPTUNE0 bits of USBNC_n_PHY_CFG1.
> -- samsung,picophy-dc-vol-level-adjust: HS DC Voltage Level Adjustment.
> - Adjust the high-speed transmitter DC level voltage.
> - The range is from 0x0 to 0xf, the default value is 0x3.
> - Details can refer to TXVREFTUNE0 bits of USBNC_n_PHY_CFG1.
> -
> -Example:
> -
> - usb@f7ed0000 {
> - compatible = "chipidea,usb2";
> - reg = <0xf7ed0000 0x10000>;
> - interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&chip CLKID_USB0>;
> - phys = <&usb_phy0>;
> - phy-names = "usb-phy";
> - vbus-supply = <&reg_usb0_vbus>;
> - itc-setting = <0x4>; /* 4 micro-frames */
> - /* Incremental burst of unspecified length */
> - ahb-burst-config = <0x0>;
> - tx-burst-size-dword = <0x10>; /* 64 bytes */
> - rx-burst-size-dword = <0x10>;
> - extcon = <0>, <&usb_id>;
> - phy-clkgate-delay-us = <400>;
> - mux-controls = <&usb_switch>;
> - mux-control-names = "usb_switch";
> - };
> -
> -Example for HSIC:
> -
> - usb@2184400 {
> - compatible = "fsl,imx6q-usb", "fsl,imx27-usb";
> - reg = <0x02184400 0x200>;
> - interrupts = <0 41 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&clks IMX6QDL_CLK_USBOH3>;
> - fsl,usbphy = <&usbphynop1>;
> - fsl,usbmisc = <&usbmisc 2>;
> - phy_type = "hsic";
> - dr_mode = "host";
> - ahb-burst-config = <0x0>;
> - tx-burst-size-dword = <0x10>;
> - rx-burst-size-dword = <0x10>;
> - pinctrl-names = "idle", "active";
> - pinctrl-0 = <&pinctrl_usbh2_idle>;
> - pinctrl-1 = <&pinctrl_usbh2_active>;
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - usbnet: ethernet@1 {
> - compatible = "usb424,9730";
> - reg = <1>;
> - };
> - };
> diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.yaml b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.yaml
> new file mode 100644
> index 000000000000..1c10691c45f2
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.yaml
> @@ -0,0 +1,306 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/usb/ci-hdrc-usb2.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: USB2 ChipIdea USB controller for ci13xxx Binding
> +
> +maintainers:
> + - Greg Kroah-Hartman <gregkh@linuxfoundation.org>
> +
> +properties:
> + compatible:
> + oneOf:
> + - enum:
> + - chipidea,usb2
> + - lsi,zevio-usb
> + - nvidia,tegra20-udc
> + - nvidia,tegra30-udc
> + - nvidia,tegra114-udc
> + - nvidia,tegra124-udc
> + - qcom,ci-hdrc
> + - items:
> + - enum:
> + - fsl,imx23-usb
> + - fsl,imx25-usb
> + - fsl,imx28-usb
> + - fsl,imx6q-usb
> + - fsl,imx6sl-usb
> + - fsl,imx6sx-usb
> + - fsl,imx6ul-usb
> + - fsl,imx7d-usb
> + - const: fsl,imx27-usb
> + - items:
> + - const: fsl,imx7ulp-usb
> + - const: fsl,imx6ul-usb
> + - items:
> + - const: lsi,zevio-usb

You already have this in first enum.

> + - items:
> + - const: xlnx,zynq-usb-2.20a
> + - const: chipidea,usb2
> + reg:
> + maxItems: 1
> +
> + interrupts:
> + maxItems: 1
> +

Your patches have several white-space issues.

Don't send patches which fail checkpatch.

> + clocks:
> + maxItems: 2
> +
> + itc-setting:
> + description:
> + interrupt threshold control register control, the setting should be
> + aligned with ITC bits at register USBCMD.
> + $ref: /schemas/types.yaml#/definitions/uint32
> +
> + ahb-burst-config:
> + description:
> + it is vendor dependent, the required value should be aligned with
> + AHBBRST at SBUSCFG, the range is from 0x0 to 0x7. This property is
> + used to change AHB burst configuration, check the chipidea spec for
> + meaning of each value. If this property is not existed, it will use
> + the reset value.
> + $ref: /schemas/types.yaml#/definitions/uint32
> + minimum: 0x0
> + maximum: 0x7
> +
> + tx-burst-size-dword:
> + description:
> + it is vendor dependent, the tx burst size in dword (4 bytes), This
> + register represents the maximum length of a the burst in 32-bit
> + words while moving data from system memory to the USB bus, the value
> + of this property will only take effect if property "ahb-burst-config"
> + is set to 0, if this property is missing the reset default of the
> + hardware implementation will be used.
> + $ref: /schemas/types.yaml#/definitions/uint32
> +
> + rx-burst-size-dword:
> + description:
> + it is vendor dependent, the rx burst size in dword (4 bytes), This
> + register represents the maximum length of a the burst in 32-bit words
> + while moving data from the USB bus to system memory, the value of
> + this property will only take effect if property "ahb-burst-config"
> + is set to 0, if this property is missing the reset default of the
> + hardware implementation will be used.
> + $ref: /schemas/types.yaml#/definitions/uint32
> +
> + extcon:
> + description: |
> + Phandles to external connector devices. First phandle should point
> + to external connector, which provide "USB" cable events, the second
> + should point to external connector device, which provide "USB-HOST"
> + cable events. If one of the external connector devices is not
> + required, empty <0> phandle should be specified.
> +
> + phy-clkgate-delay-us:
> + description: |
> + The delay time (us) between putting the PHY into low power mode and
> + gating the PHY clock.
> +
> + non-zero-ttctrl-ttha:
> + description: |
> + After setting this property, the value of register ttctrl.ttha
> + will be 0x7f; if not, the value will be 0x0, this is the default
> + value. It needs to be very carefully for setting this property, it
> + is recommended that consult with your IC engineer before setting
> + this value. On the most of chipidea platforms, the "usage_tt" flag
> + at RTL is 0, so this property only affects siTD.
> +
> + If this property is not set, the max packet size is 1023 bytes, and
> + if the total of packet size for pervious transactions are more than
> + 256 bytes, it can't accept any transactions within this frame. The
> + use case is single transaction, but higher frame rate.
> +
> + If this property is set, the max packet size is 188 bytes, it can
> + handle more transactions than above case, it can accept transactions
> + until it considers the left room size within frame is less than 188
> + bytes, software needs to make sure it does not send more than 90%
> + maximum_periodic_data_per_frame. The use case is multiple
> + transactions, but less frame rate.
> +
> + mux-controls:
> + description: |
> + The mux control for toggling host/device output of this controller.
> + It's expected that a mux state of 0 indicates device mode and a mux
> + state of 1 indicates host mode.
> +
> + mux-control-names:
> + description: Shall be "usb_switch" if mux-controls is specified.

Just define the item here.

> +
> + pinctrl-names:
> + description: |
> + Names for optional pin modes in "default", "host", "device".
> + In case of HSIC-mode, "idle" and "active" pin modes are mandatory.
> + In this case, the "idle" state needs to pull down the data and
> + strobe pin and the "active" state needs to pull up the strobe pin.

Describe the items. Otherwise this does not make much sense, because
core allows it.

> +
> + pinctrl-0:
> + maxItems: 1
> +
> + pinctrl-1:
> + maxItems: 1
> +
> + phys:
> + maxItems: 1
> +
> + phy-names:
> + const: usb-phy
> +
> + vbus-supply:
> + description: reference to the VBUS regulator.
> +
> +required:
> + - compatible
> + - reg
> + - interrupts
> +
> +allOf:
> + - $ref: usb-drd.yaml#
> + - $ref: usb-hcd.yaml#
> + - if:
> + properties:
> + mux-controls:
> + true
> + then:
> + properties:
> + mux-control-names:
> + const: usb_switch
> + - if:
> + properties:
> + phy_type:
> + const: hsic
> +
> + required:
> + - phy_type
> + then:
> + properties:
> + pinctrl-names:
> + items:
> + - const: idle
> + - const: active
> + else:
> + properties:
> + pinctrl-names:
> + oneOf:
> + - items:
> + - const: default
> + - enum:
> + - host
> + - device
> + - items:
> + - const: default
> + - if:
> + properties:
> + compatible:
> + enum:
> + - fsl,imx23-usb
> + - fsl,imx25-usb
> + - fsl,imx27-usb
> + - fsl,imx28-usb
> + - fsl,imx6q-usb
> + - fsl,imx6sl-usb
> + - fsl,imx6sx-usb
> + - fsl,imx6ul-usb
> + - fsl,imx7d-usb
> + - fsl,imx7ulp-usb
> + then:
> + properties:
> + fsl,usbmisc:

What's the type? Which other schema defined it?

Same applies to several other properties - are you sure they are already
defined by some other schema?
> +...

Best regards,
Krzysztof

\
 
 \ /
  Last update: 2022-10-12 15:24    [W:0.165 / U:1.340 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site