lkml.org 
[lkml]   [2022]   [Oct]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    Patch in this message
    /
    From
    Subject[PATCH 3/3] hwmon: (max6639) Change from pdata to dt configuration
    Date
    From: Marcello Sylvester Bauer <sylv@sylv.io>

    max6639_platform_data is not used by any in-kernel driver and does not
    address the MAX6639 channels separately. Move to device tree
    configuration with explicit properties to configure each channel.

    Non-DT platform can still use this module with its default
    configuration.

    Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
    Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
    ---
    drivers/hwmon/max6639.c | 251 +++++++++++++++++++-------
    include/linux/platform_data/max6639.h | 15 --
    2 files changed, 188 insertions(+), 78 deletions(-)
    delete mode 100644 include/linux/platform_data/max6639.h

    diff --git a/drivers/hwmon/max6639.c b/drivers/hwmon/max6639.c
    index 9b895402c80d..cbe3c5dc7e4b 100644
    --- a/drivers/hwmon/max6639.c
    +++ b/drivers/hwmon/max6639.c
    @@ -19,48 +19,53 @@
    #include <linux/hwmon-sysfs.h>
    #include <linux/err.h>
    #include <linux/mutex.h>
    -#include <linux/platform_data/max6639.h>

    /* Addresses to scan */
    static const unsigned short normal_i2c[] = { 0x2c, 0x2e, 0x2f, I2C_CLIENT_END };

    /* The MAX6639 registers, valid channel numbers: 0, 1 */
    #define MAX6639_REG_TEMP(ch) (0x00 + (ch))
    -#define MAX6639_REG_STATUS 0x02
    +#define MAX6639_REG_STATUS 0x02
    #define MAX6639_REG_OUTPUT_MASK 0x03
    -#define MAX6639_REG_GCONFIG 0x04
    +#define MAX6639_REG_GCONFIG 0x04
    #define MAX6639_REG_TEMP_EXT(ch) (0x05 + (ch))
    #define MAX6639_REG_ALERT_LIMIT(ch) (0x08 + (ch))
    #define MAX6639_REG_OT_LIMIT(ch) (0x0A + (ch))
    #define MAX6639_REG_THERM_LIMIT(ch) (0x0C + (ch))
    #define MAX6639_REG_FAN_CONFIG1(ch) (0x10 + (ch) * 4)
    -#define MAX6639_REG_FAN_CONFIG2a(ch) (0x11 + (ch) * 4)
    -#define MAX6639_REG_FAN_CONFIG2b(ch) (0x12 + (ch) * 4)
    +#define MAX6639_REG_FAN_CONFIG2a(ch) (0x11 + (ch) * 4)
    +#define MAX6639_REG_FAN_CONFIG2b(ch) (0x12 + (ch) * 4)
    #define MAX6639_REG_FAN_CONFIG3(ch) (0x13 + (ch) * 4)
    #define MAX6639_REG_FAN_CNT(ch) (0x20 + (ch))
    #define MAX6639_REG_TARGET_CNT(ch) (0x22 + (ch))
    #define MAX6639_REG_FAN_PPR(ch) (0x24 + (ch))
    #define MAX6639_REG_TARGTDUTY(ch) (0x26 + (ch))
    -#define MAX6639_REG_FAN_START_TEMP(ch) (0x28 + (ch))
    -#define MAX6639_REG_DEVID 0x3D
    -#define MAX6639_REG_MANUID 0x3E
    -#define MAX6639_REG_DEVREV 0x3F
    +#define MAX6639_REG_FAN_START_TEMP(ch) (0x28 + (ch))
    +#define MAX6639_REG_DEVID 0x3D
    +#define MAX6639_REG_MANUID 0x3E
    +#define MAX6639_REG_DEVREV 0x3F

    /* Register bits */
    +#define MAX6639_REG_OUTPUT_MASK_OT(x, ch) (x << (5 - ch))
    +#define MAX6639_REG_OUTPUT_MASK_THERM(x, ch) (x << (3 - ch))
    +#define MAX6639_REG_OUTPUT_MASK_FANFAIL(x, ch) (x << (1 - ch))
    #define MAX6639_GCONFIG_STANDBY 0x80
    -#define MAX6639_GCONFIG_POR 0x40
    -#define MAX6639_GCONFIG_DISABLE_TIMEOUT 0x20
    +#define MAX6639_GCONFIG_POR 0x40
    +#define MAX6639_GCONFIG_DISABLE_TIMEOUT 0x20
    #define MAX6639_GCONFIG_CH2_LOCAL 0x10
    #define MAX6639_GCONFIG_PWM_FREQ_HI 0x08

    #define MAX6639_FAN_CONFIG1_PWM 0x80

    +#define MAX6639_FAN_CONFIG3_THERM_FULL_SPEED 0x40
    +#define MAX6639_FAN_CONFIG3_SPIN_UP_DISABLE 0x80
    #define MAX6639_FAN_CONFIG3_THERM_FULL_SPEED 0x40

    static const int rpm_ranges[] = { 2000, 4000, 8000, 16000 };

    #define FAN_FROM_REG(val, rpm_range) ((val) == 0 || (val) == 255 ? \
    0 : (rpm_ranges[rpm_range] * 30) / (val))
    +
    #define TEMP_LIMIT_TO_REG(val) clamp_val((val) / 1000, 0, 255)

    /*
    @@ -69,7 +74,7 @@ static const int rpm_ranges[] = { 2000, 4000, 8000, 16000 };
    struct max6639_data {
    struct i2c_client *client;
    struct mutex update_lock;
    - bool valid; /* true if following fields are valid */
    + char valid; /* !=0 if following fields are valid */
    unsigned long last_updated; /* In jiffies */

    /* Register values sampled regularly */
    @@ -85,9 +90,14 @@ struct max6639_data {
    u8 temp_ot[2]; /* OT Temperature, 0..255 C (->_emergency) */

    /* Register values initialized only once */
    - u8 ppr; /* Pulses per rotation 0..3 for 1..4 ppr */
    - u8 rpm_range; /* Index in above rpm_ranges table */
    -
    + u8 ppr[2]; /* Pulses per rotation 0..3 for 1..4 ppr */
    + u8 rpm_range[2]; /* Index in above rpm_ranges table */
    + u8 pwm_polarity[2]; /* Fans PWM polarity, 0..1 */
    + bool full_speed_on_therm[2]; /* disable THERM full speed assertion */
    + bool spin_up_enable[2]; /* Enable fan spin-up if fan is not spinning */
    + bool ot_indication[2]; /* Enable OT pin indication */
    + bool therm_indication[2]; /* Enable THERM pin indication */
    + bool fan_fail_indication[2]; /* Enable FANFAIL pin indication */
    /* Optional regulator for FAN supply */
    struct regulator *reg;
    };
    @@ -144,7 +154,7 @@ static struct max6639_data *max6639_update_device(struct device *dev)
    }

    data->last_updated = jiffies;
    - data->valid = true;
    + data->valid = 1;
    }
    abort:
    mutex_unlock(&data->update_lock);
    @@ -319,7 +329,7 @@ static ssize_t fan_input_show(struct device *dev,
    return PTR_ERR(data);

    return sprintf(buf, "%d\n", FAN_FROM_REG(data->fan[attr->index],
    - data->rpm_range));
    + data->rpm_range[attr->index]));
    }

    static ssize_t alarm_show(struct device *dev,
    @@ -386,28 +396,26 @@ static struct attribute *max6639_attrs[] = {
    ATTRIBUTE_GROUPS(max6639);

    /*
    - * returns respective index in rpm_ranges table
    - * 1 by default on invalid range
    + * Get respective index in rpm_ranges table
    */
    -static int rpm_range_to_reg(int range)
    +static int rpm_range_to_index(u8 *index, int range)
    {
    int i;

    for (i = 0; i < ARRAY_SIZE(rpm_ranges); i++) {
    - if (rpm_ranges[i] == range)
    - return i;
    + if (range <= rpm_ranges[i])
    + break;
    }

    - return 1; /* default: 4000 RPM */
    + // If provided RPM is more than 16000 RPM then select 16000 RPM.
    + *index = i;
    + return 0;
    }

    static int max6639_init_client(struct i2c_client *client,
    struct max6639_data *data)
    {
    - struct max6639_platform_data *max6639_info =
    - dev_get_platdata(&client->dev);
    - int i;
    - int rpm_range = 1; /* default: 4000 RPM */
    + int i, val;
    int err;

    /* Reset chip to default values, see below for GCONFIG setup */
    @@ -416,58 +424,40 @@ static int max6639_init_client(struct i2c_client *client,
    if (err)
    goto exit;

    - /* Fans pulse per revolution is 2 by default */
    - if (max6639_info && max6639_info->ppr > 0 &&
    - max6639_info->ppr < 5)
    - data->ppr = max6639_info->ppr;
    - else
    - data->ppr = 2;
    - data->ppr -= 1;
    -
    - if (max6639_info)
    - rpm_range = rpm_range_to_reg(max6639_info->rpm_range);
    - data->rpm_range = rpm_range;
    -
    for (i = 0; i < 2; i++) {

    /* Set Fan pulse per revolution */
    err = i2c_smbus_write_byte_data(client,
    MAX6639_REG_FAN_PPR(i),
    - data->ppr << 6);
    + data->ppr[i] << 6);
    if (err)
    goto exit;

    /* Fans config PWM, RPM */
    err = i2c_smbus_write_byte_data(client,
    MAX6639_REG_FAN_CONFIG1(i),
    - MAX6639_FAN_CONFIG1_PWM | rpm_range);
    + MAX6639_FAN_CONFIG1_PWM | data->rpm_range[i]);
    if (err)
    goto exit;

    - /* Fans PWM polarity high by default */
    - if (max6639_info && max6639_info->pwm_polarity == 0)
    - err = i2c_smbus_write_byte_data(client,
    - MAX6639_REG_FAN_CONFIG2a(i), 0x00);
    - else
    - err = i2c_smbus_write_byte_data(client,
    - MAX6639_REG_FAN_CONFIG2a(i), 0x02);
    - if (err)
    - goto exit;
    + /* Fans PWM polarity */
    + err = i2c_smbus_write_byte_data(client,
    + MAX6639_REG_FAN_CONFIG2a(i), data->pwm_polarity[i] ? 0x00 : 0x02);

    /*
    - * /THERM full speed enable,
    + * Full speed on therm, spin-up at zero rpm.
    * PWM frequency 25kHz, see also GCONFIG below
    */
    err = i2c_smbus_write_byte_data(client,
    MAX6639_REG_FAN_CONFIG3(i),
    - MAX6639_FAN_CONFIG3_THERM_FULL_SPEED | 0x03);
    + (data->full_speed_on_therm[i] ?
    + MAX6639_FAN_CONFIG3_THERM_FULL_SPEED : 0) |
    + (data->spin_up_enable[i] ?
    + 0 : MAX6639_FAN_CONFIG3_SPIN_UP_DISABLE) | 0x03);
    +
    if (err)
    goto exit;

    - /* Max. temp. 80C/90C/100C */
    - data->temp_therm[i] = 80;
    - data->temp_alert[i] = 90;
    - data->temp_ot[i] = 100;
    err = i2c_smbus_write_byte_data(client,
    MAX6639_REG_THERM_LIMIT(i),
    data->temp_therm[i]);
    @@ -483,13 +473,24 @@ static int max6639_init_client(struct i2c_client *client,
    if (err)
    goto exit;

    - /* PWM 120/120 (i.e. 100%) */
    - data->pwm[i] = 120;
    err = i2c_smbus_write_byte_data(client,
    MAX6639_REG_TARGTDUTY(i), data->pwm[i]);
    if (err)
    goto exit;
    }
    +
    + val = 0;
    + for (i = 0; i < 2; i++) {
    + val |= MAX6639_REG_OUTPUT_MASK_OT(
    + data->ot_indication[i], i);
    + val |= MAX6639_REG_OUTPUT_MASK_THERM(
    + data->therm_indication[i], i);
    + val |= MAX6639_REG_OUTPUT_MASK_FANFAIL(
    + data->fan_fail_indication[i], i);
    + }
    + /* Configure output mask register */
    + err = i2c_smbus_write_byte_data(client, MAX6639_REG_OUTPUT_MASK, val);
    +
    /* Start monitoring */
    err = i2c_smbus_write_byte_data(client, MAX6639_REG_GCONFIG,
    MAX6639_GCONFIG_DISABLE_TIMEOUT | MAX6639_GCONFIG_CH2_LOCAL |
    @@ -524,12 +525,104 @@ static void max6639_regulator_disable(void *data)
    regulator_disable(data);
    }

    +static int max6639_probe_child_from_dt(struct i2c_client *client,
    + struct device_node *child,
    + struct max6639_data *data)
    +
    +{
    + struct device *dev = &client->dev;
    + u32 i, val;
    + int err;
    +
    + err = of_property_read_u32(child, "reg", &i);
    + if (err) {
    + dev_err(dev, "missing reg property of %pOFn\n", child);
    + return err;
    + }
    +
    + if (i >= 2) {
    + dev_err(dev, "invalid reg %d of %pOFn\n", i, child);
    + return -EINVAL;
    + }
    +
    + err = of_property_read_u32(child, "pulses-per-revolution", &val);
    + if (err) {
    + dev_err(dev, "missing pulses-per-revolution property of %pOFn\n", child);
    + return err;
    + }
    +
    + if (val < 0 || val > 5) {
    + dev_err(dev, "invalid pulses-per-revolution %d of %pOFn\n", val, child);
    + return -EINVAL;
    + }
    + data->ppr[i] = val;
    +
    + err = of_property_read_u32(child, "max-rpm", &val);
    + if (err) {
    + dev_err(dev, "missing rpm-range property of %pOFn\n", child);
    + return err;
    + }
    +
    + err = rpm_range_to_index(&data->rpm_range[i], val);
    + if (err) {
    + dev_err(dev, "invalid rpm-range %d of %pOFn\n", val, child);
    + return err;
    + }
    +
    + data->pwm_polarity[i] = of_property_read_bool(child, "pwm-polarity-inverse");
    +
    + err = of_property_read_u32(child, "target-rpm", &val);
    + /* Convert to PWM from provided target RPM */
    + if (!err && val != 0)
    + data->pwm[i] =
    + (u8)(val * 255 / rpm_ranges[data->rpm_range[i]]);
    +
    + data->spin_up_enable[i] = of_property_read_bool(child, "maxim,fan-spin-up");
    +
    + data->full_speed_on_therm[i] = of_property_read_bool(child,
    + "maxim,full-speed-on-therm");
    +
    + data->fan_fail_indication[i] = of_property_read_bool(child, "maxim,fanfail_indication");
    +
    + return 0;
    +}
    +
    +static int max6639_probe_from_dt(struct i2c_client *client, struct max6639_data *data)
    +{
    + struct device *dev = &client->dev;
    + const struct device_node *np = dev->of_node;
    + struct device_node *child;
    + int err;
    +
    + /* Compatible with non-DT platforms */
    + if (!np)
    + return 0;
    +
    + for_each_child_of_node(np, child) {
    + if (strcmp(child->name, "fan"))
    + continue;
    +
    + err = max6639_probe_child_from_dt(client, child, data);
    + if (err) {
    + of_node_put(child);
    + return err;
    + }
    + }
    +
    + data->ot_indication[0] = !of_property_read_bool(np, "ot0_indication");
    + data->ot_indication[1] = !of_property_read_bool(np, "ot1_indication");
    + data->therm_indication[0] = !of_property_read_bool(np, "therm0_indication");
    + data->therm_indication[1] = !of_property_read_bool(np, "therm1_indication");
    +
    + return 0;
    +}
    +
    static int max6639_probe(struct i2c_client *client)
    {
    struct device *dev = &client->dev;
    struct max6639_data *data;
    struct device *hwmon_dev;
    - int err;
    + int err, i;

    data = devm_kzalloc(dev, sizeof(struct max6639_data), GFP_KERNEL);
    if (!data)
    @@ -539,9 +632,11 @@ static int max6639_probe(struct i2c_client *client)

    data->reg = devm_regulator_get_optional(dev, "fan");
    if (IS_ERR(data->reg)) {
    - if (PTR_ERR(data->reg) != -ENODEV)
    - return PTR_ERR(data->reg);
    -
    + if (PTR_ERR(data->reg) != -ENODEV) {
    + err = (int)PTR_ERR(data->reg);
    + dev_warn(dev, "Failed looking up fan supply: %d\n", err);
    + return err;
    + }
    data->reg = NULL;
    } else {
    /* Spin up fans */
    @@ -560,6 +655,25 @@ static int max6639_probe(struct i2c_client *client)

    mutex_init(&data->update_lock);

    + /* default values */
    + for (i = 0; i < 2; i++) {
    + /* 4000 RPM */
    + data->rpm_range[i] = 1;
    + data->ppr[i] = 2;
    + data->pwm_polarity[i] = 1;
    + /* Max. temp. 80C/90C/100C */
    + data->temp_therm[i] = 80;
    + data->temp_alert[i] = 90;
    + data->temp_ot[i] = 100;
    + /* PWM 120/120 (i.e. 100%) */
    + data->pwm[i] = 120;
    + data->full_speed_on_therm[i] = false;
    + }
    +
    + err = max6639_probe_from_dt(client, data);
    + if (err)
    + return err;
    +
    /* Initialize the max6639 chip */
    err = max6639_init_client(client, data);
    if (err < 0)
    @@ -571,6 +685,7 @@ static int max6639_probe(struct i2c_client *client)
    return PTR_ERR_OR_ZERO(hwmon_dev);
    }

    +#if IS_ENABLED(CONFIG_PM_SLEEP)
    static int max6639_suspend(struct device *dev)
    {
    struct i2c_client *client = to_i2c_client(dev);
    @@ -608,6 +723,7 @@ static int max6639_resume(struct device *dev)
    return i2c_smbus_write_byte_data(client,
    MAX6639_REG_GCONFIG, ret & ~MAX6639_GCONFIG_STANDBY);
    }
    +#endif

    static const struct i2c_device_id max6639_id[] = {
    {"max6639", 0},
    @@ -616,13 +732,22 @@ static const struct i2c_device_id max6639_id[] = {

    MODULE_DEVICE_TABLE(i2c, max6639_id);

    -static DEFINE_SIMPLE_DEV_PM_OPS(max6639_pm_ops, max6639_suspend, max6639_resume);
    +#ifdef CONFIG_OF
    +static const struct of_device_id maxim_of_platform_match[] = {
    + {.compatible = "maxim,max6639"},
    + {},
    +};
    +MODULE_DEVICE_TABLE(of, maxim_of_platform_match);
    +#endif
    +
    +static SIMPLE_DEV_PM_OPS(max6639_pm_ops, max6639_suspend, max6639_resume);

    static struct i2c_driver max6639_driver = {
    .class = I2C_CLASS_HWMON,
    .driver = {
    .name = "max6639",
    .pm = pm_sleep_ptr(&max6639_pm_ops),
    + .of_match_table = of_match_ptr(maxim_of_platform_match),
    },
    .probe_new = max6639_probe,
    .id_table = max6639_id,
    diff --git a/include/linux/platform_data/max6639.h b/include/linux/platform_data/max6639.h
    deleted file mode 100644
    index 65bfdb4fdc15..000000000000
    --- a/include/linux/platform_data/max6639.h
    +++ /dev/null
    @@ -1,15 +0,0 @@
    -/* SPDX-License-Identifier: GPL-2.0 */
    -#ifndef _LINUX_MAX6639_H
    -#define _LINUX_MAX6639_H
    -
    -#include <linux/types.h>
    -
    -/* platform data for the MAX6639 temperature sensor and fan control */
    -
    -struct max6639_platform_data {
    - bool pwm_polarity; /* Polarity low (0) or high (1, default) */
    - int ppr; /* Pulses per rotation 1..4 (default == 2) */
    - int rpm_range; /* 2000, 4000 (default), 8000 or 16000 */
    -};
    -
    -#endif /* _LINUX_MAX6639_H */
    --
    2.37.3
    \
     
     \ /
      Last update: 2022-10-10 22:34    [W:3.542 / U:0.108 seconds]
    ©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site