lkml.org 
[lkml]   [2022]   [Jan]   [31]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [RFC PATCH v2 3/5] vfio/pci: fix memory leak during D3hot to D0 tranistion
From
On 1/28/2022 5:35 AM, Alex Williamson wrote:
> External email: Use caution opening links or attachments
>
>
> On Mon, 24 Jan 2022 23:47:24 +0530
> Abhishek Sahu <abhsahu@nvidia.com> wrote:
>
>> If needs_pm_restore is set (PCI device does not have support for no
>> soft reset), then the current PCI state will be saved during D0->D3hot
>> transition and same will be restored back during D3hot->D0 transition.
>> For saving the PCI state locally, pci_store_saved_state() is being
>> used and the pci_load_and_free_saved_state() will free the allocated
>> memory.
>>
>> But for reset related IOCTLs, vfio driver calls PCI reset related
>> API's which will internally change the PCI power state back to D0. So,
>> when the guest resumes, then it will get the current state as D0 and it
>> will skip the call to vfio_pci_set_power_state() for changing the
>> power state to D0 explicitly. In this case, the memory pointed by
>> pm_save will never be freed.
>>
>> Also, in malicious sequence, the state changing to D3hot followed by
>> VFIO_DEVICE_RESET/VFIO_DEVICE_PCI_HOT_RESET can be run in loop and
>> it can cause an OOM situation. This patch stores the power state locally
>> and uses the same for comparing the current power state. For the
>> places where D0 transition can happen, call vfio_pci_set_power_state()
>> to transition to D0 state. Since the vfio power state is still D3hot,
>> so this D0 transition will help in running the logic required
>> from D3hot->D0 transition. Also, to prevent any miss during
>> future development to detect this condition, this patch puts a
>> check and frees the memory after printing warning.
>>
>> This locally saved power state will help in subsequent patches
>> also.
>
> Ideally let's put fixes patches at the start of the series, or better
> yet send them separately, and don't include changes that only make
> sense in the context of a subsequent patch.
>
> Fixes: 51ef3a004b1e ("vfio/pci: Restore device state on PM transition")
>

Thanks Alex for reviewing this patch.
I have added Fixes tag and sent this patch separately.

Should I update this patch series or you are planning to review the
other patches first of this patch series first.

>> Signed-off-by: Abhishek Sahu <abhsahu@nvidia.com>
>> ---
>> drivers/vfio/pci/vfio_pci_core.c | 53 ++++++++++++++++++++++++++++++--
>> include/linux/vfio_pci_core.h | 1 +
>> 2 files changed, 51 insertions(+), 3 deletions(-)
>>
>> diff --git a/drivers/vfio/pci/vfio_pci_core.c b/drivers/vfio/pci/vfio_pci_core.c
>> index c6e4fe9088c3..ee2fb8af57fa 100644
>> --- a/drivers/vfio/pci/vfio_pci_core.c
>> +++ b/drivers/vfio/pci/vfio_pci_core.c
>> @@ -206,6 +206,14 @@ static void vfio_pci_probe_power_state(struct vfio_pci_core_device *vdev)
>> * restore when returned to D0. Saved separately from pci_saved_state for use
>> * by PM capability emulation and separately from pci_dev internal saved state
>> * to avoid it being overwritten and consumed around other resets.
>> + *
>> + * There are few cases where the PCI power state can be changed to D0
>> + * without the involvement of this API. So, cache the power state locally
>> + * and call this API to update the D0 state. It will help in running the
>> + * logic that is needed for transitioning to the D0 state. For example,
>> + * if needs_pm_restore is set, then the PCI state will be saved locally.
>> + * The memory taken for saving this PCI state needs to be freed to
>> + * prevent memory leak.
>> */
>> int vfio_pci_set_power_state(struct vfio_pci_core_device *vdev, pci_power_t state)
>> {
>> @@ -214,20 +222,34 @@ int vfio_pci_set_power_state(struct vfio_pci_core_device *vdev, pci_power_t stat
>> int ret;
>>
>> if (vdev->needs_pm_restore) {
>> - if (pdev->current_state < PCI_D3hot && state >= PCI_D3hot) {
>> + if (vdev->power_state < PCI_D3hot && state >= PCI_D3hot) {
>> pci_save_state(pdev);
>> needs_save = true;
>> }
>>
>> - if (pdev->current_state >= PCI_D3hot && state <= PCI_D0)
>> + if (vdev->power_state >= PCI_D3hot && state <= PCI_D0)
>> needs_restore = true;
>> }
>>
>> ret = pci_set_power_state(pdev, state);
>>
>> if (!ret) {
>> + vdev->power_state = pdev->current_state;
>> +
>> /* D3 might be unsupported via quirk, skip unless in D3 */
>> - if (needs_save && pdev->current_state >= PCI_D3hot) {
>> + if (needs_save && vdev->power_state >= PCI_D3hot) {
>> + /*
>> + * If somehow, the vfio driver was not able to free the
>> + * memory allocated in pm_save, then free the earlier
>> + * memory first before overwriting pm_save to prevent
>> + * memory leak.
>> + */
>> + if (vdev->pm_save) {
>> + pci_warn(pdev,
>> + "Overwriting saved PCI state pointer so freeing the earlier memory\n");
>> + kfree(vdev->pm_save);
>> + }
>
> The minimal fix for the described issue would simply be:
>
> kfree(vdev->pm_save);
>
> It seems like the only purpose of the warning is try to make sure we
> haven't missed any wake-up calls, where this would be a pretty small
> breadcrumb to actually debug such an issue.
>

I have removed the warning in the updated patch.

>> +
>> vdev->pm_save = pci_store_saved_state(pdev);
>> } else if (needs_restore) {
>> pci_load_and_free_saved_state(pdev, &vdev->pm_save);
>> @@ -326,6 +348,14 @@ void vfio_pci_core_disable(struct vfio_pci_core_device *vdev)
>> /* For needs_reset */
>> lockdep_assert_held(&vdev->vdev.dev_set->lock);
>>
>> + /*
>> + * If disable has been called while the power state is other than D0,
>> + * then set the power state in vfio driver to D0. It will help
>> + * in running the logic needed for D0 power state. The subsequent
>> + * runtime PM API's will put the device into the low power state again.
>> + */
>> + vfio_pci_set_power_state(vdev, PCI_D0);
>> +
>
> I do think we have an issue here, but the reason is that pci_pm_reset()
> returns -EINVAL if we try to reset a device that isn't currently in D0.
> Therefore any path where we're triggering a function reset that could
> use a PM reset and we don't know if the device is in D0, should wake up
> the device before we try that reset.
>
> We're about to load the initial state of the device that was saved when
> it was opened, so I don't think pdev->current_state vs
> vdev->power_state matters here, we only care that the device is in D0.
>

I have added this point in the commit message of the updated patch.

>> /* Stop the device from further DMA */
>> pci_clear_master(pdev);
>>
>> @@ -929,6 +959,15 @@ long vfio_pci_core_ioctl(struct vfio_device *core_vdev, unsigned int cmd,
>>
>> vfio_pci_zap_and_down_write_memory_lock(vdev);
>> ret = pci_try_reset_function(vdev->pdev);
>> +
>> + /*
>> + * If pci_try_reset_function() has been called while the power
>> + * state is other than D0, then pci_try_reset_function() will
>> + * internally set the device state to D0 without vfio driver
>> + * interaction. Update the power state in vfio driver to perform
>> + * the logic needed for D0 power state.
>> + */
>> + vfio_pci_set_power_state(vdev, PCI_D0);
>
> For the case where pci_try_reset_function() might use a PM reset, we
> should set D0 before that call. In doing so, the pdev->current_state
> should match the actual device power state, so we still don't need to
> stash power state on the vdev.
>

I have set D0 state before calling pci_try_reset_function() in
the updated patch.

>> up_write(&vdev->memory_lock);
>>
>> return ret;
>> @@ -2071,6 +2110,14 @@ static int vfio_pci_dev_set_hot_reset(struct vfio_device_set *dev_set,
>>
>> err_undo:
>> list_for_each_entry(cur, &dev_set->device_list, vdev.dev_set_list) {
>> + /*
>> + * If pci_reset_bus() has been called while the power
>> + * state is other than D0, then pci_reset_bus() will
>> + * internally set the device state to D0 without vfio driver
>> + * interaction. Update the power state in vfio driver to perform
>> + * the logic needed for D0 power state.
>> + */
>> + vfio_pci_set_power_state(cur, PCI_D0);
>
> Here pci_reset_bus() will wakeup the device and I think the concern is
> that around that bus reset we'll save and restore the device state, but
> that's potentially bogus device state if waking it triggers a soft
> reset. We could again wake devices before the reset to make the state
> correct, or we could test pm_save and perform the load and restore if
> it exists. Either of those would avoid needing to cache the power
> state on the vdev. Thanks,
>

I have made the changes to wake-up the devices.

Thanks
Abhishek

> Alex
>
>> if (cur == cur_mem)
>> is_mem = false;
>> if (cur == cur_vma)
>> diff --git a/include/linux/vfio_pci_core.h b/include/linux/vfio_pci_core.h
>> index aafe09c9fa64..05db838e72cc 100644
>> --- a/include/linux/vfio_pci_core.h
>> +++ b/include/linux/vfio_pci_core.h
>> @@ -124,6 +124,7 @@ struct vfio_pci_core_device {
>> bool needs_reset;
>> bool nointx;
>> bool needs_pm_restore;
>> + pci_power_t power_state;
>> struct pci_saved_state *pci_saved_state;
>> struct pci_saved_state *pm_save;
>> int ioeventfds_nr;
>

\
 
 \ /
  Last update: 2022-01-31 13:09    [W:0.094 / U:0.088 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site