lkml.org 
[lkml]   [2022]   [Jan]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v1 0/4] fbtft: Unorphan the driver for maintenance
On Thu, 27 Jan 2022 at 12:11, Daniel Vetter <daniel@ffwll.ch> wrote:
>
> On Thu, Jan 27, 2022 at 11:32:58AM +0100, Dmitry Vyukov wrote:
> > On Thu, 27 Jan 2022 at 07:30, Dan Carpenter <dan.carpenter@oracle.com> wrote:
> > >
> > > On Wed, Jan 26, 2022 at 11:31:02PM +0100, Daniel Vetter wrote:
> > > > dOn Wed, Jan 26, 2022 at 3:46 PM Dan Carpenter <dan.carpenter@oracle.com> wrote:
> > > > >
> > > > > The other advantage of staging is the I don't think syzbot enables it.
> > > > > I guess it's easier to persuade Dmitry to ignore STAGING than it was to
> > > > > get him to disable FBDEV. :P
> > > > >
> > > > > The memory corruption in fbdev was a real headache for everyone because
> > > > > the stack traces ended up all over the kernel.
> > > >
> > > > Uh Dmitry disabled all of FBDEV?
> > >
> > > No that's the opposite of what I meant. STAGING is disabled in syzbot
> > > and FBDEV is enabled.
> >
> > Is there still any problem with syzbot config?
> > syzbot configs are stored here:
> > https://github.com/google/syzkaller/tree/master/dashboard/config/linux
>
> CONFIG_FB and CONFIG_FRAMEBUFFER_CONSOLE are set, which are the things I
> care about. The one exception is upstream-kcsan.config, which doesn't have
> fbcon enabled.
>
> Also looking through your fbdev drivers, really the only ones you want to
> ever enable are:
> CONFIG_FB_VGA16=y
> CONFIG_FB_VESA=y
> CONFIG_FB_VIRTUAL=y
>
> The following isn't enabled, but I guess if you don't have EFI doesn't
> make sense, otherwise you really want it:
> CONFIG_FB_EFI=y
>
> The below are enabled in some configs and should be ditched
> CONFIG_FB_SIMPLE=y (use CONFIG_DRM_SIMPLEDRM instead, at least on kernels that have it)
> CONFIG_FB_I740=y (you don't have this hw or I'm blown away, this last shipped 20 years ago)
> CONFIG_FB_UDL=y (use CONFIG_DRM_UDL instead)
> CONFIG_FB_UVESA=y (does modesets by calling into a userspace helper to run x86 vbios code, just don't)
> CONFIG_FB_SMSCUFX=y (if you really have these then someone should port this to drm asap)
> CONFIG_FB_CIRRUS=y (use CONFIG_DRM_CIRRUS_QEMU instead since I'm pretty sure you don't have a real cirrus pci card)
>
> Also note that the simpledrm driver will eat all the firmware fbdev
> drivers and unload them. So you need to run two configs to really cover
> both sets of drivers in all cases.

Thanks!

I've sent PR to update these configs as you suggest:
https://github.com/google/syzkaller/pull/2993

\
 
 \ /
  Last update: 2022-01-27 17:34    [W:0.318 / U:0.020 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site