lkml.org 
[lkml]   [2022]   [Jan]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v4 3/3] dmaengine: sf-pdma: Get number of channel by device tree
From
On Sun, 16 Jan 2022 17:35:28 PST (-0800), zong.li@sifive.com wrote:
> It currently assumes that there are always four channels, it would
> cause the error if there is actually less than four channels. Change
> that by getting number of channel from device tree.
>
> For backwards-compatible, it uses the default value (i.e. 4) when there
> is no 'dma-channels' information in dts.

Some of the same wording issues here as those I pointed out in the DT
bindings patch.

> Signed-off-by: Zong Li <zong.li@sifive.com>
> ---
> drivers/dma/sf-pdma/sf-pdma.c | 20 +++++++++++++-------
> drivers/dma/sf-pdma/sf-pdma.h | 8 ++------
> 2 files changed, 15 insertions(+), 13 deletions(-)
>
> diff --git a/drivers/dma/sf-pdma/sf-pdma.c b/drivers/dma/sf-pdma/sf-pdma.c
> index f12606aeff87..1264add9897e 100644
> --- a/drivers/dma/sf-pdma/sf-pdma.c
> +++ b/drivers/dma/sf-pdma/sf-pdma.c
> @@ -482,9 +482,7 @@ static void sf_pdma_setup_chans(struct sf_pdma *pdma)
> static int sf_pdma_probe(struct platform_device *pdev)
> {
> struct sf_pdma *pdma;
> - struct sf_pdma_chan *chan;
> struct resource *res;
> - int len, chans;
> int ret;
> const enum dma_slave_buswidth widths =
> DMA_SLAVE_BUSWIDTH_1_BYTE | DMA_SLAVE_BUSWIDTH_2_BYTES |
> @@ -492,13 +490,21 @@ static int sf_pdma_probe(struct platform_device *pdev)
> DMA_SLAVE_BUSWIDTH_16_BYTES | DMA_SLAVE_BUSWIDTH_32_BYTES |
> DMA_SLAVE_BUSWIDTH_64_BYTES;
>
> - chans = PDMA_NR_CH;
> - len = sizeof(*pdma) + sizeof(*chan) * chans;
> - pdma = devm_kzalloc(&pdev->dev, len, GFP_KERNEL);
> + pdma = devm_kzalloc(&pdev->dev, sizeof(*pdma), GFP_KERNEL);
> if (!pdma)
> return -ENOMEM;
>
> - pdma->n_chans = chans;
> + ret = of_property_read_u32(pdev->dev.of_node, "dma-channels",
> + &pdma->n_chans);
> + if (ret) {
> + dev_notice(&pdev->dev, "set number of channels to default value: 4\n");
> + pdma->n_chans = PDMA_MAX_NR_CH;
> + }
> +
> + if (pdma->n_chans > PDMA_MAX_NR_CH) {
> + dev_err(&pdev->dev, "the number of channels exceeds the maximum\n");
> + return -EINVAL;

Can we get away with just using only the number of channels the driver
actually supports? ie, just never sending an op to the channels above
MAX_NR_CH? That should leave us with nothing to track.

> + }
>
> res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> pdma->membase = devm_ioremap_resource(&pdev->dev, res);
> @@ -556,7 +562,7 @@ static int sf_pdma_remove(struct platform_device *pdev)
> struct sf_pdma_chan *ch;
> int i;
>
> - for (i = 0; i < PDMA_NR_CH; i++) {
> + for (i = 0; i < pdma->n_chans; i++) {
> ch = &pdma->chans[i];
>
> devm_free_irq(&pdev->dev, ch->txirq, ch);
> diff --git a/drivers/dma/sf-pdma/sf-pdma.h b/drivers/dma/sf-pdma/sf-pdma.h
> index 0c20167b097d..8127d792f639 100644
> --- a/drivers/dma/sf-pdma/sf-pdma.h
> +++ b/drivers/dma/sf-pdma/sf-pdma.h
> @@ -22,11 +22,7 @@
> #include "../dmaengine.h"
> #include "../virt-dma.h"
>
> -#define PDMA_NR_CH 4
> -
> -#if (PDMA_NR_CH != 4)
> -#error "Please define PDMA_NR_CH to 4"
> -#endif
> +#define PDMA_MAX_NR_CH 4
>
> #define PDMA_BASE_ADDR 0x3000000
> #define PDMA_CHAN_OFFSET 0x1000
> @@ -118,7 +114,7 @@ struct sf_pdma {
> void __iomem *membase;
> void __iomem *mappedbase;
> u32 n_chans;
> - struct sf_pdma_chan chans[PDMA_NR_CH];
> + struct sf_pdma_chan chans[PDMA_MAX_NR_CH];
> };
>
> #endif /* _SF_PDMA_H */

\
 
 \ /
  Last update: 2022-01-20 19:52    [W:0.106 / U:0.388 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site