lkml.org 
[lkml]   [2022]   [Jan]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2] phy: dphy: Correct clk_pre parameter
From
Date
On 19/01/2022 09:40, Neil Armstrong wrote:
> Hi,
>
> On 19/01/2022 03:37, Liu Ying wrote:
>> The D-PHY specification (v1.2) explicitly mentions that the T-CLK-PRE
>> parameter's unit is Unit Interval(UI) and the minimum value is 8. Also,
>> kernel doc of the 'clk_pre' member of struct phy_configure_opts_mipi_dphy
>> mentions that it should be in UI. However, the dphy core driver wrongly
>> sets 'clk_pre' to 8000, which seems to hint that it's in picoseconds.
>> And, the kernel doc of the 'clk_pre' member wrongly says the minimum value
>> is '8 UI', instead of 8.
>>
>> So, let's fix both the dphy core driver and the kernel doc of the 'clk_pre'
>> member to correctly reflect the T-CLK-PRE parameter's unit and the minimum
>> value according to the D-PHY specification.
>>
>> I'm assuming that all impacted custom drivers shall program values in
>> TxByteClkHS cycles into hardware for the T-CLK-PRE parameter. The D-PHY
>> specification mentions that the frequency of TxByteClkHS is exactly 1/8
>> the High-Speed(HS) bit rate(each HS bit consumes one UI). So, relevant
>> custom driver code is changed to program those values as
>> DIV_ROUND_UP(cfg->clk_pre, BITS_PER_BYTE), then.
>>
>> Note that I've only tested the patch with RM67191 DSI panel on i.MX8mq EVK.
>> Help is needed to test with other i.MX8mq, Meson and Rockchip platforms,
>> as I don't have the hardwares.
>>
>> Fixes: 2ed869990e14 ("phy: Add MIPI D-PHY configuration options")
>> Cc: Andrzej Hajda <andrzej.hajda@intel.com>
>> Cc: Neil Armstrong <narmstrong@baylibre.com>
>> Cc: Robert Foss <robert.foss@linaro.org>
>> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
>> Cc: Jonas Karlman <jonas@kwiboo.se>
>> Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
>> Cc: David Airlie <airlied@linux.ie>
>> Cc: Daniel Vetter <daniel@ffwll.ch>
>> Cc: Kishon Vijay Abraham I <kishon@ti.com>
>> Cc: Vinod Koul <vkoul@kernel.org>
>> Cc: Kevin Hilman <khilman@baylibre.com>
>> Cc: Jerome Brunet <jbrunet@baylibre.com>
>> Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
>> Cc: Heiko Stuebner <heiko@sntech.de>
>> Cc: Maxime Ripard <mripard@kernel.org>
>> Cc: Guido Günther <agx@sigxcpu.org>
>> Tested-by: Liu Ying <victor.liu@nxp.com> # RM67191 DSI panel on i.MX8mq EVK
>> Signed-off-by: Liu Ying <victor.liu@nxp.com>
>> ---
>> v1->v2:
>> * Use BITS_PER_BYTE macro. (Andrzej)
>> * Drop dsi argument from ui2bc() in nwl-dsi.c.
>>
>> drivers/gpu/drm/bridge/nwl-dsi.c | 12 +++++-------
>> drivers/phy/amlogic/phy-meson-axg-mipi-dphy.c | 3 ++-
>> drivers/phy/phy-core-mipi-dphy.c | 4 ++--
>> drivers/phy/rockchip/phy-rockchip-inno-dsidphy.c | 3 ++-
>> include/linux/phy/phy-mipi-dphy.h | 2 +-
>> 5 files changed, 12 insertions(+), 12 deletions(-)
>>
[...]

>> diff --git a/drivers/phy/amlogic/phy-meson-axg-mipi-dphy.c b/drivers/phy/amlogic/phy-meson-axg-mipi-dphy.c
>> index cd2332bf0e31..fdbd64c03e12 100644
>> --- a/drivers/phy/amlogic/phy-meson-axg-mipi-dphy.c
>> +++ b/drivers/phy/amlogic/phy-meson-axg-mipi-dphy.c
>> @@ -9,6 +9,7 @@
>>
>> #include <linux/bitfield.h>
>> #include <linux/bitops.h>
>> +#include <linux/bits.h>
>> #include <linux/clk.h>
>> #include <linux/delay.h>
>> #include <linux/io.h>
>> @@ -250,7 +251,7 @@ static int phy_meson_axg_mipi_dphy_power_on(struct phy *phy)
>> (DIV_ROUND_UP(priv->config.clk_zero, temp) << 16) |
>> (DIV_ROUND_UP(priv->config.clk_prepare, temp) << 24));
>> regmap_write(priv->regmap, MIPI_DSI_CLK_TIM1,
>> - DIV_ROUND_UP(priv->config.clk_pre, temp));
>> + DIV_ROUND_UP(priv->config.clk_pre, BITS_PER_BYTE));
>>
>> regmap_write(priv->regmap, MIPI_DSI_HS_TIM,
>> DIV_ROUND_UP(priv->config.hs_exit, temp) |
>
> I'll try to run a test, currently the calculation gives 2, so this would give 1.

The Amlogic vendor code does:

/* >8*ui */
#define DPHY_TIME_CLK_PRE(ui) (10 * ui)

t_ui = lcd_timing.bit_rate

t_ui = (1000000 * 100) / (dsi_ui / 1000); /*100*ns */
temp = t_ui * 8; /* lane_byte cycle time */

dphy->clk_pre = ((DPHY_TIME_CLK_PRE(t_ui) + temp - 1) / temp) & 0xff;

PHY Registers only says:
MIPI_DSI_CLK_TIM1 [31:0]
7:0 R/W 0 tCLK_PRE

>
> Neil
>

[...]

\
 
 \ /
  Last update: 2022-01-19 10:12    [W:0.079 / U:0.748 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site