lkml.org 
[lkml]   [2022]   [Jan]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH v3 3/3] ARM: dts: Add support for Samsung Chagall WiFi
Date
Hi Henrik,

>-----Original Message-----
>From: Henrik Grimler [mailto:henrik@grimler.se]
>Sent: Monday, January 17, 2022 2:30 AM
>To: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
>Cc: semen.protsenko@linaro.org; virag.david003@gmail.com;
>martin.juecker@gmail.com; cw00.choi@samsung.com;
>m.szyprowski@samsung.com; alim.akhtar@samsung.com;
>robh+dt@kernel.org; devicetree@vger.kernel.org; linux-samsung-
>soc@vger.kernel.org; linux-arm-kernel@lists.infradead.org; linux-
>kernel@vger.kernel.org; ~postmarketos/upstreaming@lists.sr.ht
>Subject: Re: [PATCH v3 3/3] ARM: dts: Add support for Samsung Chagall WiFi
>
>Hi Krzysztof,
>
>> > +/* External sdcard */
>> > +&mmc_2 {
>> > + status = "okay";
>> > + bus-width = <4>;
>> > + cap-sd-highspeed;
>> > + card-detect-delay = <200>;
>> > + pinctrl-0 = <&sd2_clk &sd2_cmd &mmc2_cd &sd2_bus1 &sd2_bus4>;
>> > + pinctrl-names = "default";
>> > + samsung,dw-mshc-ciu-div = <3>;
>> > + samsung,dw-mshc-ddr-timing = <0 2>;
>> > + samsung,dw-mshc-sdr-timing = <0 4>;
>> > + sd-uhs-sdr50;
>> > + vmmc-supply = <&ldo19_reg>;
>> > + vqmmc-supply = <&ldo13_reg>;
>> > +};
>> > +
>> > +&pinctrl_0 {
>> > + mmc2_cd: sd2-cd-pins {
>> > + samsung,pins = "gpx2-4";
>>
>> Interesting... I looked at vendor sources to board-chagall and
>> standard pin gpc2-2 is mentioned as PULL down and not-connected
>comment.
>>
>> gpx2-4 seems not mentioned at all, unless other board files are
>> actually used.
>
>Gpio seems to be spread out. GPIO_T_FLASH_DETECT is defined as gpx2-4 in
>board-universal5420-mmc.c, and then used for card detection.
>(Looking at it now again I see that write protection through sd2_wp should
>also be supported for mmc_2, can add that in next patch set.)
>
Card detect pin is generally a special function (dedicated pin) pin,
directly connected from SoC to card external slot.
And for exynos5420 it is gpc2-2 as pointed by Krzysztof.
Also PIN_FUNC_2 for gpx2-4 indicate that it is wakeup_int2 function.
Do you get a card detect interrupt when removing and inserting the card to
the card slot?
Also to avoid confusion, probably you can change the node name as "mmc2_cd:
mmc2-cd-pins"
(as sd2-cd-pins is gpc2-2 for this SoC)


>> Anyway, if it works for you, it's good.
>>
>> Rest looks ok, I'll apply after the merge window.
>
>Thanks!
>
>> Best regards,
>> Krzysztof
>
>Best regards,
>Henrik Grimler

\
 
 \ /
  Last update: 2022-01-17 06:52    [W:0.157 / U:0.152 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site