lkml.org 
[lkml]   [2022]   [Jan]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] mmc: sdhci-of-esdhc: Check for error num after setting mask
From
Date
On 06/01/2022 04:16, Jiasheng Jiang wrote:
> Because of the possible failure of the dma_supported(), the
> dma_set_mask_and_coherent() may return error num.
> Therefore, it should be better to check it and return the error if
> fails.
> Also, the caller, esdhc_of_resume(), should deal with the return value.
> Moreover, as the sdhci_esdhc_driver has not been used, it does not need to
> be considered.

Apologies, but that last sentence I don't understand. Can you clarify it a bit.
What doesn't need to be considered and why?

>
> Fixes: 5552d7ad596c ("mmc: sdhci-of-esdhc: set proper dma mask for ls104x chips")
> Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
> ---
> drivers/mmc/host/sdhci-of-esdhc.c | 13 ++++++++++---
> 1 file changed, 10 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/mmc/host/sdhci-of-esdhc.c b/drivers/mmc/host/sdhci-of-esdhc.c
> index a593b1fbd69e..bedfc7bb5174 100644
> --- a/drivers/mmc/host/sdhci-of-esdhc.c
> +++ b/drivers/mmc/host/sdhci-of-esdhc.c
> @@ -524,12 +524,16 @@ static void esdhc_of_adma_workaround(struct sdhci_host *host, u32 intmask)
>
> static int esdhc_of_enable_dma(struct sdhci_host *host)
> {
> + int ret;
> u32 value;
> struct device *dev = mmc_dev(host->mmc);
>
> if (of_device_is_compatible(dev->of_node, "fsl,ls1043a-esdhc") ||
> - of_device_is_compatible(dev->of_node, "fsl,ls1046a-esdhc"))
> - dma_set_mask_and_coherent(dev, DMA_BIT_MASK(40));
> + of_device_is_compatible(dev->of_node, "fsl,ls1046a-esdhc")) {
> + ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(40));
> + if (ret)
> + return ret;
> + }
>
> value = sdhci_readl(host, ESDHC_DMA_SYSCTL);
>
> @@ -1245,7 +1249,10 @@ static int esdhc_of_resume(struct device *dev)
>
> if (ret == 0) {
> /* Isn't this already done by sdhci_resume_host() ? --rmk */
> - esdhc_of_enable_dma(host);
> + ret = esdhc_of_enable_dma(host);
> + if (ret)
> + return ret;
> +

This is already done by sdhci_resume_host(), which assumes there can be no
error if DMA has been enabled previously i.e. -> enable_dma() is called
at setup and the return value checked then. If it is possible that DMA
support can disappear later, then it would be better to address that in
SDHCI so that all SDHCI drivers get the benefit.

> sdhci_writel(host, esdhc_proctl, SDHCI_HOST_CONTROL);
> }
> return ret;
>

\
 
 \ /
  Last update: 2022-01-12 08:07    [W:0.083 / U:0.056 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site