lkml.org 
[lkml]   [2022]   [Jan]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH v3 23/23] media: atmel: atmel-isc: change format propagation to subdev into only verification
Hi Eugen

On Mon, Dec 13, 2021 at 03:49:40PM +0200, Eugen Hristev wrote:
> As a top MC video driver, the atmel-isc should not propagate the format to the
> subdevice.
> It should rather check at streamon() time if the subdev is properly configured
> with a compatible format.
> Removed the whole format finding logic, and reworked the format verification
> at streamon time, such that the ISC will return an error if the subdevice
> is not properly configured.
> With this being done, the module parameter 'sensor_prefered' makes no sense
> anymore. The ISC should not decide which format the sensor is using. The
> ISC should only cope with the situation and inform userspace if the streaming
> is possible in the current configuration.

Sounds great!

>
> Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
> ---
> Changes in v3:
> - clamp to maximum resolution once the frame size from the subdev is found
>
> drivers/media/platform/atmel/atmel-isc-base.c | 271 ++++++++----------
> drivers/media/platform/atmel/atmel-isc.h | 1 +
> 2 files changed, 126 insertions(+), 146 deletions(-)
>
> diff --git a/drivers/media/platform/atmel/atmel-isc-base.c b/drivers/media/platform/atmel/atmel-isc-base.c
> index 31c8e3029eee..00c8c9588a78 100644
> --- a/drivers/media/platform/atmel/atmel-isc-base.c
> +++ b/drivers/media/platform/atmel/atmel-isc-base.c
> @@ -36,11 +36,6 @@ static unsigned int debug;
> module_param(debug, int, 0644);
> MODULE_PARM_DESC(debug, "debug level (0-2)");
>
> -static unsigned int sensor_preferred = 1;
> -module_param(sensor_preferred, uint, 0644);
> -MODULE_PARM_DESC(sensor_preferred,
> - "Sensor is preferred to output the specified format (1-on 0-off), default 1");
> -
> #define ISC_IS_FORMAT_RAW(mbus_code) \
> (((mbus_code) & 0xf000) == 0x3000)
>
> @@ -532,7 +527,7 @@ static int isc_enum_fmt_vid_cap(struct file *file, void *priv,
> * convert it to any of the formats that we usually can with a
> * RAW sensor. Thus, do not advertise them.
> */
> - if (!isc->config.sd_format ||
> + if (isc->config.sd_format &&

Is this change intentional ?

> !ISC_IS_FORMAT_RAW(isc->config.sd_format->mbus_code))
> return -EINVAL;
>
> @@ -621,20 +616,30 @@ static int isc_try_validate_formats(struct isc_device *isc)
> break;
> default:
> /* any other different formats are not supported */
> + v4l2_err(&isc->v4l2_dev, "Requested unsupported format.\n");
> ret = -EINVAL;
> }
> v4l2_dbg(1, debug, &isc->v4l2_dev,
> "Format validation, requested rgb=%u, yuv=%u, grey=%u, bayer=%u\n",
> rgb, yuv, grey, bayer);

Would it make sense to move this before the switch so that the
error messages, if any, appear later ?

>
> - /* we cannot output RAW if we do not receive RAW */
> - if ((bayer) && !ISC_IS_FORMAT_RAW(isc->try_config.sd_format->mbus_code))
> + if ((bayer) &&
> + !ISC_IS_FORMAT_RAW(isc->try_config.sd_format->mbus_code)) {
> + v4l2_err(&isc->v4l2_dev, "Cannot output RAW if we do not receive RAW.\n");
> return -EINVAL;
> + }
>
> - /* we cannot output GREY if we do not receive RAW/GREY */
> if (grey && !ISC_IS_FORMAT_RAW(isc->try_config.sd_format->mbus_code) &&
> - !ISC_IS_FORMAT_GREY(isc->try_config.sd_format->mbus_code))
> + !ISC_IS_FORMAT_GREY(isc->try_config.sd_format->mbus_code)) {
> + v4l2_err(&isc->v4l2_dev, "Cannot output GREY if we do not receive RAW/GREY.\n");
> return -EINVAL;
> + }
> +
> + if ((rgb || bayer || yuv) &&
> + ISC_IS_FORMAT_GREY(isc->try_config.sd_format->mbus_code)) {
> + v4l2_err(&isc->v4l2_dev, "Cannot convert GREY to another format.\n");
> + return -EINVAL;
> + }
>
> return ret;
> }
> @@ -862,7 +867,7 @@ static void isc_try_fse(struct isc_device *isc,
> * If we do not know yet which format the subdev is using, we cannot
> * do anything.
> */
> - if (!isc->try_config.sd_format)
> + if (!isc->config.sd_format)
> return;
>
> fse.code = isc->try_config.sd_format->mbus_code;
> @@ -883,180 +888,141 @@ static void isc_try_fse(struct isc_device *isc,
> }
> }
>
> -static int isc_try_fmt(struct isc_device *isc, struct v4l2_format *f,
> - u32 *code)
> +static int isc_try_fmt(struct isc_device *isc, struct v4l2_format *f)
> {
> - int i;
> - struct isc_format *sd_fmt = NULL, *direct_fmt = NULL;
> struct v4l2_pix_format *pixfmt = &f->fmt.pix;
> - struct v4l2_subdev_pad_config pad_cfg = {};
> - struct v4l2_subdev_state pad_state = {
> - .pads = &pad_cfg
> - };
> - struct v4l2_subdev_format format = {
> - .which = V4L2_SUBDEV_FORMAT_TRY,
> - };
> - u32 mbus_code;
> - int ret;
> - bool rlp_dma_direct_dump = false;
> + unsigned int i;
>
> if (f->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
> return -EINVAL;
>
> - /* Step 1: find a RAW format that is supported */
> - for (i = 0; i < isc->num_user_formats; i++) {
> - if (ISC_IS_FORMAT_RAW(isc->user_formats[i]->mbus_code)) {
> - sd_fmt = isc->user_formats[i];
> + isc->try_config.fourcc = isc->user_formats[0]->fourcc;
> +
> + /* find if the format requested is supported */
> + for (i = 0; i < isc->controller_formats_size; i++)
> + if (isc->controller_formats[i].fourcc == pixfmt->pixelformat) {
> + isc->try_config.fourcc = pixfmt->pixelformat;
> break;
> }
> - }
> - /* Step 2: We can continue with this RAW format, or we can look
> - * for better: maybe sensor supports directly what we need.
> - */
> - direct_fmt = find_format_by_fourcc(isc, pixfmt->pixelformat);
> -
> - /* Step 3: We have both. We decide given the module parameter which
> - * one to use.
> - */
> - if (direct_fmt && sd_fmt && sensor_preferred)
> - sd_fmt = direct_fmt;
> -
> - /* Step 4: we do not have RAW but we have a direct format. Use it. */
> - if (direct_fmt && !sd_fmt)
> - sd_fmt = direct_fmt;
> -
> - /* Step 5: if we are using a direct format, we need to package
> - * everything as 8 bit data and just dump it
> - */
> - if (sd_fmt == direct_fmt)
> - rlp_dma_direct_dump = true;
> -
> - /* Step 6: We have no format. This can happen if the userspace
> - * requests some weird/invalid format.
> - * In this case, default to whatever we have
> - */
> - if (!sd_fmt && !direct_fmt) {
> - sd_fmt = isc->user_formats[isc->num_user_formats - 1];
> - v4l2_dbg(1, debug, &isc->v4l2_dev,
> - "Sensor not supporting %.4s, using %.4s\n",
> - (char *)&pixfmt->pixelformat, (char *)&sd_fmt->fourcc);
> - }
> -
> - if (!sd_fmt) {
> - ret = -EINVAL;
> - goto isc_try_fmt_err;
> - }
> -
> - /* Step 7: Print out what we decided for debugging */
> - v4l2_dbg(1, debug, &isc->v4l2_dev,
> - "Preferring to have sensor using format %.4s\n",
> - (char *)&sd_fmt->fourcc);
> -
> - /* Step 8: at this moment we decided which format the subdev will use */
> - isc->try_config.sd_format = sd_fmt;
> -
> - /* Limit to Atmel ISC hardware capabilities */
> - if (pixfmt->width > isc->max_width)
> - pixfmt->width = isc->max_width;
> - if (pixfmt->height > isc->max_height)
> - pixfmt->height = isc->max_height;
> -
> - /*
> - * The mbus format is the one the subdev outputs.
> - * The pixels will be transferred in this format Sensor -> ISC
> - */
> - mbus_code = sd_fmt->mbus_code;
> -
> - /*
> - * Validate formats. If the required format is not OK, default to raw.
> - */
> -
> - isc->try_config.fourcc = pixfmt->pixelformat;
> -
> - if (isc_try_validate_formats(isc)) {
> - pixfmt->pixelformat = isc->try_config.fourcc = sd_fmt->fourcc;
> - /* Re-try to validate the new format */
> - ret = isc_try_validate_formats(isc);
> - if (ret)
> - goto isc_try_fmt_err;
> - }
> -
> - ret = isc_try_configure_rlp_dma(isc, rlp_dma_direct_dump);
> - if (ret)
> - goto isc_try_fmt_err;
> -
> - ret = isc_try_configure_pipeline(isc);
> - if (ret)
> - goto isc_try_fmt_err;
>
> - /* Obtain frame sizes if possible to have crop requirements ready */
> - isc_try_fse(isc, &pad_state);
> -
> - v4l2_fill_mbus_format(&format.format, pixfmt, mbus_code);
> - ret = v4l2_subdev_call(isc->current_subdev->sd, pad, set_fmt,
> - &pad_state, &format);
> - if (ret < 0)
> - goto isc_try_fmt_subdev_err;
> + /* If we did not find the requested format, we will fallback here */
> + pixfmt->pixelformat = isc->try_config.fourcc;
> + pixfmt->colorspace = V4L2_COLORSPACE_SRGB;
> + pixfmt->field = V4L2_FIELD_NONE;
>
> - v4l2_fill_pix_format(pixfmt, &format.format);
> + isc_try_configure_rlp_dma(isc, false);
>
> /* Limit to Atmel ISC hardware capabilities */
> - if (pixfmt->width > isc->max_width)
> - pixfmt->width = isc->max_width;
> - if (pixfmt->height > isc->max_height)
> - pixfmt->height = isc->max_height;
> + v4l_bound_align_image(&pixfmt->width, 16, isc->max_width, 0,
> + &pixfmt->height, 16, isc->max_height, 0, 0);
>
> pixfmt->field = V4L2_FIELD_NONE;
> pixfmt->bytesperline = (pixfmt->width * isc->try_config.bpp_v4l2) >> 3;
> pixfmt->sizeimage = ((pixfmt->width * isc->try_config.bpp) >> 3) *
> pixfmt->height;
>
> - if (code)
> - *code = mbus_code;
> + isc->try_fmt = *f;
>
> return 0;
> +}
>
> -isc_try_fmt_err:
> - v4l2_err(&isc->v4l2_dev, "Could not find any possible format for a working pipeline\n");
> -isc_try_fmt_subdev_err:
> - memset(&isc->try_config, 0, sizeof(isc->try_config));
> +static int isc_set_fmt(struct isc_device *isc, struct v4l2_format *f)
> +{
> + isc_try_fmt(isc, f);
>
> - return ret;
> + /* make the try configuration active */
> + isc->config = isc->try_config;
> + isc->fmt = isc->try_fmt;
> +
> + v4l2_dbg(1, debug, &isc->v4l2_dev, "ISC set_fmt to %.4s @%dx%d\n",
> + (char *)&f->fmt.pix.pixelformat,
> + f->fmt.pix.width, f->fmt.pix.height);
> +
> + return 0;
> }
>
> -static int isc_set_fmt(struct isc_device *isc, struct v4l2_format *f)
> +static int isc_validate(struct isc_device *isc)
> {
> + int ret;
> + int i;
> + struct isc_format *sd_fmt = NULL;
> + struct v4l2_pix_format *pixfmt = &isc->fmt.fmt.pix;
> struct v4l2_subdev_format format = {
> .which = V4L2_SUBDEV_FORMAT_ACTIVE,
> + .pad = isc->remote_pad,
> + };
> + struct v4l2_subdev_pad_config pad_cfg = {};
> + struct v4l2_subdev_state pad_state = {
> + .pads = &pad_cfg,
> };
> - u32 mbus_code = 0;
> - int ret;
>
> - ret = isc_try_fmt(isc, f, &mbus_code);
> + /* Get current format from subdev */
> + ret = v4l2_subdev_call(isc->current_subdev->sd, pad, get_fmt, NULL,
> + &format);

Ah! Haven't you just said we don't care anymore about the subdev
format ? :)

Kidding, I might got a bit lost in the logic, but if I look at your
above isc_try_validate_formats() it seems like an ideal candidate for
.link_validate() media_entity operation.

Just to make sure we're on the same page, here's how it should ideally
look like:
- set format does care about subdev format. It only checks that the
format required from the user is one of the ISC supported one. Ie.
no v4l2_subdev_call()

- as s_stream time your top driver calls media_pipeline_start()

- media_pipeline_start() walks all the entities in the pipeline and
validates the format of connected pads. To validate formats the
__media_pipeline_start() functions calls link_validate() on each
entity. You should in your driver set

static const struct media_entity_operations your_media_entity_ops = {
.link_validate = v4l2_subdev_link_validate,
};

if you want to use the default link validation procedure, or set the
callback to your custom validation function, which can behave more
or less like isc_try_validate_formats()

Does it match your understanding too ?

Thanks
j



> if (ret)
> return ret;
>
> - v4l2_fill_mbus_format(&format.format, &f->fmt.pix, mbus_code);
> - ret = v4l2_subdev_call(isc->current_subdev->sd, pad,
> - set_fmt, NULL, &format);
> - if (ret < 0)
> - return ret;
> + /* Identify the subdev's format configuration */
> + for (i = 0; i < isc->num_user_formats; i++)
> + if (isc->user_formats[i]->mbus_code == format.format.code) {
> + sd_fmt = isc->user_formats[i];
> + break;
> + }
> +
> + /* Check if the format is not supported */
> + if (!sd_fmt) {
> + v4l2_err(&isc->v4l2_dev,
> + "Current subdevice is streaming a media bus code that is not supported 0x%x\n",
> + format.format.code);
> + return -EPIPE;
> + }
> +
> + /* At this moment we know which format the subdev will use */
> + isc->try_config.sd_format = sd_fmt;
> +
> + /* If the sensor is not RAW, we can only do a direct dump */
> + if (!ISC_IS_FORMAT_RAW(isc->try_config.sd_format->mbus_code))
> + isc_try_configure_rlp_dma(isc, true);
>
> /* Limit to Atmel ISC hardware capabilities */
> - if (f->fmt.pix.width > isc->max_width)
> - f->fmt.pix.width = isc->max_width;
> - if (f->fmt.pix.height > isc->max_height)
> - f->fmt.pix.height = isc->max_height;
> + v4l_bound_align_image(&format.format.width, 16, isc->max_width, 0,
> + &format.format.height, 16, isc->max_height, 0, 0);
>
> - isc->fmt = *f;
> + /* Check if the frame size is the same. Otherwise we may overflow */
> + if (pixfmt->height != format.format.height ||
> + pixfmt->width != format.format.width) {
> + v4l2_err(&isc->v4l2_dev,
> + "ISC not configured with the proper frame size: %dx%d\n",
> + format.format.width, format.format.height);
> + return -EPIPE;
> + }
>
> + v4l2_dbg(1, debug, &isc->v4l2_dev,
> + "Identified subdev using format %.4s with %dx%d %d bpp\n",
> + (char *)&sd_fmt->fourcc, pixfmt->width, pixfmt->height,
> + isc->try_config.bpp);
> +
> + /* Reset and restart AWB if the subdevice changed the format */
> if (isc->try_config.sd_format && isc->config.sd_format &&
> isc->try_config.sd_format != isc->config.sd_format) {
> isc->ctrls.hist_stat = HIST_INIT;
> isc_reset_awb_ctrls(isc);
> isc_update_v4l2_ctrls(isc);
> }
> - /* make the try configuration active */
> +
> + /* Validate formats */
> + ret = isc_try_validate_formats(isc);
> + if (ret)
> + return ret;
> +
> + /* Obtain frame sizes if possible to have crop requirements ready */
> + isc_try_fse(isc, &pad_state);
> +
> + /* Configure ISC pipeline for the config */
> + ret = isc_try_configure_pipeline(isc);
> + if (ret)
> + return ret;
> +
> isc->config = isc->try_config;
>
> v4l2_dbg(1, debug, &isc->v4l2_dev, "New ISC configuration in place\n");
> @@ -1064,6 +1030,19 @@ static int isc_set_fmt(struct isc_device *isc, struct v4l2_format *f)
> return 0;
> }
>
> +static int isc_streamon(struct file *file, void *priv, enum v4l2_buf_type bt)
> +{
> + struct isc_device *isc = video_drvdata(file);
> + int ret;
> +
> + ret = isc_validate(isc);
> +
> + if (ret)
> + return ret;
> +
> + return vb2_ioctl_streamon(file, priv, bt);
> +}
> +
> static int isc_s_fmt_vid_cap(struct file *file, void *priv,
> struct v4l2_format *f)
> {
> @@ -1080,7 +1059,7 @@ static int isc_try_fmt_vid_cap(struct file *file, void *priv,
> {
> struct isc_device *isc = video_drvdata(file);
>
> - return isc_try_fmt(isc, f, NULL);
> + return isc_try_fmt(isc, f);
> }
>
> static int isc_enum_input(struct file *file, void *priv,
> @@ -1176,7 +1155,7 @@ static const struct v4l2_ioctl_ops isc_ioctl_ops = {
> .vidioc_dqbuf = vb2_ioctl_dqbuf,
> .vidioc_create_bufs = vb2_ioctl_create_bufs,
> .vidioc_prepare_buf = vb2_ioctl_prepare_buf,
> - .vidioc_streamon = vb2_ioctl_streamon,
> + .vidioc_streamon = isc_streamon,
> .vidioc_streamoff = vb2_ioctl_streamoff,
>
> .vidioc_g_parm = isc_g_parm,
> @@ -1879,7 +1858,7 @@ static int isc_set_default_fmt(struct isc_device *isc)
> };
> int ret;
>
> - ret = isc_try_fmt(isc, &f, NULL);
> + ret = isc_try_fmt(isc, &f);
> if (ret)
> return ret;
>
> diff --git a/drivers/media/platform/atmel/atmel-isc.h b/drivers/media/platform/atmel/atmel-isc.h
> index c2cb805faff3..7081698adddd 100644
> --- a/drivers/media/platform/atmel/atmel-isc.h
> +++ b/drivers/media/platform/atmel/atmel-isc.h
> @@ -297,6 +297,7 @@ struct isc_device {
> struct completion comp;
>
> struct v4l2_format fmt;
> + struct v4l2_format try_fmt;
> struct isc_format **user_formats;
> unsigned int num_user_formats;
>
> --
> 2.25.1
>

\
 
 \ /
  Last update: 2022-01-12 10:21    [W:0.285 / U:0.280 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site